Page 1
SLV-ED10ME/ED10MPS/ED10PS/ED10SG/ED40ME/ED40PS/ED40SG/ED60ME/ ED60PS/ED60SG/ED70MN/EZ10AZ/EZ40AZ/EZ60AZ/EZ70AS/EZ70NZ 3 7 63 1515 0 RMT-V245/V245A/V245C/V247/V247C/V247D/V248C SERVICE MANUAL Australian Model SLV-EZ10AZ/EZ40AZ/EZ60AZ/EZ70AS E Model SLV-ED10MPS/ED10PS/ED40PS/ED60PS/ED70MN ME Model SLV-ED10ME/ED10SG/ED40ME/ ED40SG/ED60ME/ED60SG Newzealand Model SLV-EZ10AZ/EZ40AZ/EZ60AZ/EZ70NZ S MECHANISM Photo: SLV-ED70MN • Refer to the SERVICE MANUAL of VHS MECHANICAL ADJUSTMENTS VI for MECHANICAL ADJUSTMENTS.
Page 2
LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
http://www.xiaoyu163.com 3 7 63 1515 0 SERVICE NOTE 1. DISASSEMBLY • This set can be disassembled in the order shown below. Note: Pages in indicated pages in the SERVICE MANUAL. Pages in indicated pages in the VHS MECHANICAL ADJUSTMENT MANUAL VI. Upper case (Page 2-1) Front Panel...
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 SECTION 1 This section is extracted from SLV-ED70MN 3 7 63 1515 0 instruction manual. (3-865-382-11) GENERAL L 13942296513 u163 http://www.xiaoyu163.com...
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 SECTION 2 3 7 63 1515 0 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 2-1. UPPER CASE REMOVAL 2-3. REAR PANEL REMOVAL 3 Upper case 7 Rear panel 1 Two tapping screws 6 Two claws 1 Power cord 2 Two tapping screws (CN101)
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 SECTION 4 3 7 63 1515 0 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING For schematic Diagram: • Caution when replacing chip parts. BOARDS AND SCHEMATIC DIAGRAMS. New parts must be attached after removal of chip. (In addition to this, the necessary mote is printed Be careful not to heat the minus side of tantalum capacitor, in each block.)
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 3 7 6 3 1 5 1 5 0 MA-350 (VIDEO, AUDIO, I/O, SERVO/SYSTEM CONTROL, TUNER) PRINTED WIRING BOARD There are few cases that the part isn't mounted in this model is printed on this diagram. –...
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 3 7 6 3 1 5 1 5 0 NK-11 (NICAM) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: NK-11 board; 2,000 series – – SLV-ED70/EZ70: NZ – There are few cases that the part isn't mounted in this model is printed on this diagram. NK-11 NK-11 BOARD(SIDE B)
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 3 7 6 3 1 5 1 5 0 GK-12 (ZVEI TONE) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: GK-12 board; 1,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram. –...
Page 46
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 3 7 6 3 1 5 1 5 0 DM-85 (MODE CONTROL) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: DM-85 board; 2,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram. –...
Page 47
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 3 7 6 3 1 5 1 5 0 MF-317 (MODE CONTROL, FRONT IN) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: MF-317 board; 2,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram. –...
Page 48
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 3 7 6 3 1 5 1 5 0 KK-19 (EASY TIMER) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: KK-19 board; 2,000 series – – SLV-ED40/ED60/ED70/EZ40/EZ60/EZ70 – There are few cases that the part isn't mounted in this model is printed on this diagram. KK-19 BOARD EASY TIMER...
Page 49
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 3 7 6 3 1 5 1 5 0 DS-85 (MODE CONTROL), KK-18 (EASY TIMER) PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS – Ref. No.: DS-85 Board, KK-18 board; 1,000 series – – SLV-ED10/EZ10 – There are few cases that the part isn't mounted in this model is printed on this diagram. DS-85 KK-18 BOARD...
Page 50
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 3 7 6 3 1 5 1 5 0 RJ-82 (ADDITIONAL REAR IN/OUT) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: RJ-82 Board board; 1,000 series – – SLV-ED40/ED60/ED70/EZ60/EZ70 – There are few cases that the part isn't mounted in this model is printed on this diagram. CNJ951:ED40/ED60/ED70/EZ70:AS LINE-3 IN(SAT IN) RJ-82...
Page 51
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 3 7 6 3 1 5 1 5 0 HS-921SF/921SF1 (POWER SUPPLY) PRINTED WIRING BOARD – Ref. No.: HS-921SF/921SF1 board; 3,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram. –...
Page 53
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 3 7 6 3 1 5 1 5 0 SR-708/718 (POWER SUPPLY) PRINTED WIRING BOARD – Ref. No.: SR708/718 board; 4,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram. –...
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 SECTION 6 3 7 63 1515 0 ERROR CODES Table 6-2. Mode Codes in Case of Error This set displays an error code, and a mode code in case of error on the display tube, if the operation stopped by error. Code Description The following provides description concerned.
http://www.xiaoyu163.com SLV-ED10/ED40/ED60/ED70/EZ10/EZ40/EZ60/EZ70 SECTION 7 3 7 63 1515 0 ADJUSTMENTS 2-1-3. Set-up of Adjustment During the adjustment, see the Parts Arrangement In this adjustment, PAL or NTSC pattern generator is connected Diagram for Adjustments on Page 7-6. with LINE input signal terminal. When checking with tuner, con- nected AERIAL terminal.
http://www.xiaoyu163.com 3 7 63 1515 0 2-1-6. Adjusting Sequence 2-3. SERVO SYSTEM ADJUSTMENT Make the electrical adjustment in the following sequence. 2-3-1. RF Switching Position Adjustment Power supply adjustment (MA-350 BOARD) Purpose: Adjust the interval between A ch and B ch of tape playback out- put.
http://www.xiaoyu163.com 3 7 63 1515 0 2-4. AUDIO SYSTEM ADJUSTMENTS RF SWP • Adjust both Lch and Rch. [Connection] Audio Audio level meter or generator distortion meter 600 Ω 47 kΩ Attenuator AUDIO LINE IN Feed signal both AUDIO LINE OUT channelssimultaneously.
http://www.xiaoyu163.com 3 7 63 1515 0 3. Overall Level Characteristic and Distortion Factor 2-4-2. Normal Audio System Adjustment Check • Make adjustment in the SP mode, unless otherwise specified. Purpose: Use a normal VHS cassette for an adjustment tape. Check the record level, play level, and distortion factor against the •...
http://www.xiaoyu163.com 3 7 6 3 1 5 1 5 0 4. Overall Level Characteristic and Distortion Factor 2-5. TUNER SYSTEM ADJUSTMENT 2-6. PARTS ARRANGEMENT DIAGRAM FOR ADJUSTMENTS Check Purpose: [Connection] MA-350 BOARD (Side A) Check the record level, play level, and distortion factor against the reference input.
http://www.xiaoyu163.com 3 7 63 1515 0 8-1-2. CHASSIS ASSEMBLY (ED10/EZ10) supplied supplied L 13942296513 supplied supplied supplied The components identified by mark ! or dotted line with mark ! are criti- cal for safety. Replace only with part number speci- fied.
http://www.xiaoyu163.com DM-85 DS-85 GK-12 3 7 63 1515 0 8-2. ELECTRICAL PARTS LIST NOTE: The components identified by • Due to standardization, replacements in the • Items marked “*” are not stocked since they mark ! or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.