Page 1
SLV-ED1ME/ED1PS/ED1SG/ED2SA/ED3AF/ED4ME/ED4PS/ED4SG/ED5ME/ ED6ME/ED6PS/ED6SG/ED7FS/ED7MI/ED7MN/EZ1AZ/EZ4AZ/EZ7AS/EZ7NZ RMT-V245A/V245B/V247/V247A/V248A SERVICE MANUAL African Model SLV-ED3AF Australian Model SLV-EZ1AZ/EZ4AZ/EZ7AS E Model SLV-ED1PS/ED4PS/ED6PS/ED7MN/ED7FS French Model SLV-ED7FS Hong Kong Model SLV-ED7MI Irish Model SLV-ED7MI ME Model Photo: SLV-ED1 SLV-ED1ME/ED1SG/ED4ME/ED4SG/ ED5ME/ED6ME/ED6SG/ED7MI Newzealand Model SLV-EZ7NZ S MECHANISM South Afrifca Model SLV-ED2SA/ED7MI UK Model •...
Page 2
LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
• Feature Difference SLV- ED 1 ED 2 ED 3 ED 4 ED 5 ED 6 FEATURE HEAD/CH NTSC (3.58) (REC/PB) (4.43) (REC/PB) SECAM (REC/PB) ME-SECAM (REC/PB) REC (NTSC) (SP/EP) (PAL) (SP/LP) PLAY (NTSC) (SP/LP/EP) g/G/G g/G/G g/G/G (PAL) (SP/LP) g (3pin g (3pin g (3pin RCA REAR LINE IN/OUT Y.B.B) Y.B.B) Y.B.B)
SERVICE NOTE 1. DISASSEMBLY • This set can be disassembled in the order shown below. Note: Pages in indicated pages in the SERVICE MANUAL. Pages in indicated pages in the VHS MECHANICAL ADJUSTMENT MANUAL VI. Upper case (Page 2-1) Front Panel Pinch Press Ground Shaft RJ-80 Board...
SLV-ED1/ED2/ED3/ED4/ED5/ED6/ED7/EZ1/EZ4/EZ7 SECTION 2 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 2-1. UPPER CASE REMOVAL 2-3. REAR PANEL REMOVAL 7 Rear panel 3 Upper case 6 Two claws 1 Two tapping screws 1 Power cord 2 Two tapping screws (CN101) 2 Harness 4 Claw...
SLV-ED1/ED2/ED3/ED4/ED5/ED6/ED7/EZ1/EZ4/EZ7 SECTION 6 ERROR CODES Table 6-2. Mode Codes in Case of Error This set displays an error code, and a mode code in case of error on the display tube, if the operation stopped by error. Code Description The following provides description concerned. EJECT (POWER ON) Display tube (lower 5 digits) EJECT (POWER OFF)
SLV-ED1/ED2/ED3/ED4/ED5/ED6/ED7/EZ1/EZ4/EZ7 SECTION 7 ADJUSTMENTS 2-1-3. Set-up of Adjustment During the adjustment, see the Parts Arrangement In this adjustment, PAL or NTSC pattern generator is connected Diagram for Adjustments on Page 7-6. with LINE input signal terminal. When check to tuner, connected AERIAL terminal.
2-1-6. Adjusting Sequence 2-3. SERVO SYSTEM Adjustment Make the electrical adjustment in the following sequence. 2-3-1. RF Switching Position Adjustment Checking power supply (MA-323 Board) Purpose: Adjust the interval between A ch and B ch of tape playback out- put. Servo system adjustment Improve the interchangeability with other tapes and sets.
2-4. AUDIO SYSTEM ADJUSTMENTS RF SWP • Adjust both Lch and Rch. [Connection] Audio Audiolevel meter or generator distortion meter 600 Ω 47 kΩ Attenuator AUDIO LINE IN Feed signal both AUDIO LINE OUT channelssimultaneously. Fig. 7-2-5. Fig. 7-2-4. 2. Frequency Responce Check 2-4-1.
3. Overall Level Characteristic and Distortion Factor 2-4-2. Normal Audio System Adjustment Check • Make adjustment in the SP mode, unless otherwise specified. Purpose: Use a normal VHS cassette for an adjustment tape. Check the record level, play level, and distortion factor against the •...
4. Overall Level Characteristic and Distortion Factor 2-5. PARTS ARRANGEMENT DIAGRAM FOR ADJUSTMENTS Check Purpose: MA-323 BOARD (Side A) Check the record level, play level, and distortion factor against the reference input. CN501 Mode REC and PB (SP mode) Signal 400 Hz, –7.5 dBs Measurement point Audio output terminal...
8-1-2. CHASSIS ASSEMBLY (ED1/ED2/EZ1) supplied supplied supplied supplied The components identified by mark ! or dotted line with mark ! are criti- cal for safety. Replace only with part number speci- fied. Ref. No. Part No. Description Remark Ref. No. Part No.
8-1-4. CHASSIS ASSEMBLY (EXCEPT ED1/ED2/EZ1) ED7: MI, MN/ EZ7NZ ED3/ED7FS supplied supplied supplied supplied supplied EXCEPT EZ4/EZ7 supplied supplied The components identified by mark ! or dotted line with mark ! are criti- cal for safety. Replace only with part number speci- fied.
DM-76 DS-80 MA-323 8-2. ELECTRICAL PARTS LIST NOTE: The components identified by • Due to standardization, replacements in the • Items marked “*” are not stocked since they mark ! or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.