Table of Contents
Advertisement
Quick Links
1 : 8 SCALE NITRO-POWERD 4WD RACING TRUCK
This radio control model car is not a toy! Before beginning assembly, please read this manual thoroughly.
本產品為高性能模型非一般玩具，組裝與操作前，請詳閱本產品說明書。
The contents are subject to change without prior notice due to product improvements and specificatrion changes.
本套件所附之零件可能跟圖示有所差異。因產品後續之設計研發或功能不斷改善之因，我們將保留產品規格變更權力，不再另行通知使用者。
Instruction Manual & Parts Catalogue
Thunder Tiger Corporation guarantees this model kit to be free from defects in both material and workmanship. The total monetary value under
warranty will in no case exceed the cost of the original kit purchased. This warranty does not cover any components damaged by use or modification.
Part or parts missing from this kit must be reported within 60 days of purchase. No part or parts will be sent under warranty without proof of purchase.
To receive part or parts under warranty, the service center must receive a proof of purchase and/or the defective part or parts. Should you find a
defective or missing part, contact the authorized Thunder Tiger Service/Distributor nearest you. Under no circumstances can a dealer or distributor
accept return of a kit if assembly has started.
本公司對於製造過程中產生之瑕疵，負完全品質保證責任。
保證事項僅限於產品本身與隨產品所附之零配件。
品質保證不包含下列事項
因使用、組裝或調整本產品所發生之損壞。
其他所有非產品本身品質所造成之損壞。
1 : 8
引擎動力四驅競賽卡車
操作說明書及零件包型錄
WARRANTY
品質保證事項
No.6241-F
Advertisement
Table of Contents
Related Manuals for THUNDER TIGER 6241-F
Summary of Contents for THUNDER TIGER 6241-F
- Page 1 品質保證事項 Thunder Tiger Corporation guarantees this model kit to be free from defects in both material and workmanship. The total monetary value under warranty will in no case exceed the cost of the original kit purchased. This warranty does not cover any components damaged by use or modification.
-
Page 2: Table Of Contents
前言 Thank you for purchasing this Thunder Tiger product. This manual contains the steps and instructions required to assemble your car. Please read this manual completely before attempting to start maintenance. Follow the directions in this manual closely to reduce problems during operation. -
Page 3: Important Notes & Warning 重要注意事項
2. Thunder Tiger assumes and accepts no responsibility for personal and/or property damages resulting from the use of improper building materials, equipment and operations. By the act of assembling or operating this product, the user accepts all resulting liability. -
Page 4: Items Required For Operation 周邊配件
ITEMS REQUIRED FOR OPERATION 周邊配件 Screw Drivers, Lexan Body Reamer, Hobby Knife, No.2430 Glow Fuel, Methanol 10% to 30% Lexan Scissors. PRO-START Engine Starter Nitro 5% to 18% Caster / Synthetic Oil 十字起子、一字起子、挖孔器、車殼剪、美工刀 引擎啟動器 模型專用燃料(含10%~30%硝基甲烷、 5%~18%潤滑油) Tools Included 附屬工具 Hex Drive Starting Shaft Battery Box 六角引擎啟動棒... -
Page 5: Unrapping The Truck From Box And Installing The Tire
UNRAPPING THE TRUCK FROM BOX AND INSTALLING THE TIRE 從包裝盒中取出車輛，安裝輪胎 a. Remove the truck, radio, and accessories from box. b. Thread antenna wire through the tubing, and then install the antenna tube onto the box top hole(Do not cut or shorten antenna wire). c. -
Page 6: Radio Operation 遙控器操作
RADIO OPERATION 遙控器操作 a. When turning radio on, first turn on the transmitter and keep the transmitter antenna pointing straight up. b. Then, turn on the receiver. When turning off, first turn the receiver off, then the transmitter off. c. To reverse the functions of servos, use the small, white servo reverse switches located on the back of the pistol transmitter. To trim the servos on pistol transmitter, use the trim switches on side of the steering wheel (the ST. -
Page 7: Transmitter Controls 發射機各部功能簡介
TRANSMITTER CONTROLS 1. Transmitter Antenna: Straighten up the antenna before operating the model. 2. Battery Level Indicator: Three LEDs indicate the battery voltage level. If the Red LED flashes, please replace the batteries. 3. HI/LO Throttle ATV (Adjustable Travel Volume): Allows you to independently preset the maximum travel of the throttle servo either side (high / low) of neutral. -
Page 8: Binding Process 安全校頻配對步驟
BINDING PROCESS 安全校頻配對步驟 A binding feature is included in the ACE RC Cougar 2.4GHz spread spectrum system to ensure the transmitter and receiver bind properly and prevent interference from other controllers. To manually bind Tx/Rx, please proceed as per the following steps: a. -
Page 9: F/S-Fail Safe 防暴衝設定
F/S-FAIL SAFE 防暴衝設定 How to Set the Fail Safe (F/S) Position a. After binding the transmitter and receiver, you can continually set up the F/S position. Turn on the transmitter power and then receiver power. b. Press the “Binding SW” button on the receiver. 10 seconds later, the LED will turn green flash on the receiver. (Caution! Don't release the “Binding SW”... -
Page 10: Operating Radio Steering Function 遙控器設定－轉向
OPERATING RADIO STEERING FUNCTION 遙控器設定－轉向 a. Check the radio steering functions. With the radio transmitter and receiver on, turn the steering wheel/stick to the left. The front tires/wheels should turn left accordingly. If not, flip the steering servo reverse switch. b. -
Page 11: Adjusting The Throttle Linkage 油門及煞車連桿調整
ADJUSTING THROTTLE / BRAKE LINKAGE 油門及煞車連桿調整 a. To set the throttle/brake linkage, first the radio should be on and neutral; thus, the servo is at neutral position. b. With the servo at neutral, turn and adjust plastic brake adjustment nut at the end of the linkage until there is a 1/16"(1.5mm) gap between the spring and the brake lever when the spring is not compressed. -
Page 12: Adjusting Carburetor 化油器調整
ADJUSTING CARBURETOR 化油器調整 a. To set the high speed needle (large needle sticking out from the carburetor body), turn the screw as pictured. Initial high speed needle setting should be 3 turns (close the needle completely, then back out 2 1/2 turns). Clockwise turn will provide leaner setting (lower fuel to air mixture), and counterclockwise turn will provide richer setting (higher fuel to air mixture). -
Page 13: Preparing The Engine For Starting 引擎整備工作
(and it needs recharging). If it does not light up or the plug element looks distorted, then the glow plug is bad (replace with new one). After checking, reinstall the glow plug. The glow plug used for this engine can be: Thunder Tiger 9281, McCoy #9 / #59, Novarossi C4S / C5S / C6S,OS #8 / #A3 / #A5, and Picco P6S / P7S. -
Page 14: Stopping Engine 停止引擎
STOPPING THE ENGINE 停止引擎 a. Bring your truck to a complete stop and idle. Then, Remove the body clips and body. b. Using needle-nose pliers or a clothespin, pinch off the fuel line just before the carburetor until the engine stops (1-2 seconds). DO NOT ATTEMPT TO STOP THE MOTOR BY TOUCHING OR GRABBING THE FLYWHEEL! These motors have a lot of torque and serious injury could occur from stopping the engine in this manner. -
Page 15: Storing Your Car 保養建議
STORING YOUR CAR 保養建議 To keep your truck in good working condition, there are a few steps that need to be followed: a. Remove the fuel from the tank. Both your truck and squeeze bottle should always be stored free of fuel. •... -
Page 16: Ride Height
Front & Rear Toe-In / Toe-Out 前後輪束角調整 Notch a. Use a 1.5mm Allen wrench as shown to adjust the front & rear toe-in. b. Lengthening the Turnbuckles will increase the amount of toe-in, shortening them 刻槽向內 will increase the amount of toe-out. c. -
Page 17: Troubleshooting 常見問題與解決方法
TROUBLESHOOTING 常 見 問 題 與 解 決 方 法 If you have trouble starting or keeping your RTA4 running, here's a quick checklist of what to look for first. 如果您的 RTA4 有行駛上的問題，您可以參考下的說明。 如果問題無法解決，請與購買經銷商聯絡。 Description 問題 Problem 可能原因 Solution 解決方法 Engine will not Out of fuel 油箱沒油... -
Page 22: Rta4 Monster Truck Spare Parts List 零件表
RTA4 RACING TRUCK SPARE PARTS LIST 零件表 PD01-0010 9708B CLUTCH BELL, 23T AIR FILTER, 21 BLACK 離合器罩, 23T 空氣濾清器(黑) AA1813 PD01-0012 AD2555 PD01-0008 PD02-0014 FLYWHEEL SHIM (0.5mm) FLYWHEEL COLLET, 21 CLUTCH HARDWARE CLUTCH SHOES(4) CTR TRANSMISSION CASE 飛輪墊片(0.5mm) 飛輪固定座 離合器罩配件 離合器甩片(4) 齒輪箱本體... - Page 23 RTA4 RACING TRUCK SPARE PARTS LIST 零件表 PD1442 PD1444 PD1446 PD1447 PD1448 CTR TRANS SHIM & CLIP FWD/REV DRIVE GEARS FWD/REV SHIFT GEARS FWD/REV CLUTCH HUB FWD/REV MAIN SHAFT E型扣環 & 墊片 齒輪 最終齒輪組 定位甩片座組 動力輸出軸 PD1449 PD1450 PD1451 PD1452 PD1453 REV IDLE GEAR &...
- Page 24 RTA4 RACING TRUCK SPARE PARTS LIST 零件表 PD1483 PD1487 PD1488 PD1489 PD1490 DIFF CASE/BULKHEAD ORING, TUBE & OUTLET FWD/REV CLUTCH HOU. CHASSIS CHASSIS GUARD & COVER 差速箱本體 O型環, 接頭及排氣管 驅動輪組 車底板 側板 & 檔板 PD1491 PD1492 PD1493 PD1494 PD1497 ROLL BAR ROLL BAR MOUNTS UP SUSP.
- Page 25 RTA4 RACING TRUCK SPARE PARTS LIST 零件表 PD1650 1116 PD1714 PD1715 PD1740 FUEL TANK ACC 5-WAY SOCKET TOOL NUT WRENCH, 5.5/7/8mm BALL HEX DRIVE SHAFT, 6mm DRIVE CUP SET SCREW 油箱配件組 五向十字扳手組 十字扳手 啟動棒 驅動軸套固定螺栓 PD1743 PD1749 PD1755 PD6336 PD6340 MGT SHOCK BODY AND CAP MGT DIFFERENTIAL OUTDRIVES AND GASKETS SPUR GEAR, 46T...
-
Page 26: Rta4 Monster Truck Optional Parts List 選購零件表
RTA4 RACING TRUCK OPTIONAL PARTS LIST 選購零件表 PD1301 AL LOCK NUT/BLUE, M3 AA2110-R PD01-0011 PD1304 AL LOCK NUT/BLUE, M4 PD1582 PD1583 CYLINDER HEAD, 28B (R) CLUTCH BELL, 26T PD1761 AL LOCK NUT/BLUE, M5 SERVO SAVER, HITECH SERVO SAVER, JR 汽缸蓋(紅) 離合器罩, 26T 止鬆螺帽零件包(藍) 轉向伺服機臂, HITECH... - Page 27 RTA4 SPARE PARTS LIST 零件表 1116 5-WAY SOCKET TOOL 五向十字扳手組 PD1457 SLIPPER FRICTION PEGS 摩擦子 9708B AIR FILTER, 21 (BLACK) 空氣濾清器(黑) PD1458 SLIPPER HARDWARE 滑動套件 AA1813 FLYWHEEL SHIM (0.5mm) 飛輪墊片(0.5mm) PD1460 CTR TRANS CASE SCREWS 齒輪箱螺絲 AD2555 FLYWHEEL COLLET, 21 飛輪固定座...
- Page 28 RTA4 SPARE PARTS LIST 零件表 PD1562 LOCK NUT(20), FLANGE M4 凸緣止鬆螺帽 PD1711 CT P.M SCREW(20), M2.6x12 平頭十字螺絲組(20), M2.6x12 PD1563 LOCK NUT(20), FLANGE M5 尼龍墊圈螺帽 PD1712 BT P.T. SCREW(20), M2.6x8 圓頭十字自攻螺絲(20), M2.6x8 PD1565 SET SCREW(20), 4x5mm 無頭內六角螺絲(20), 4x5mm PD1714 NUT WRENCH, 5.5/7/8mm 十字板手...
Need help?
Do you have a question about the 6241-F and is the answer not in the manual?
Questions and answers