Alarm Mode; Using The Alarms - Casio 2763 Operation Manual

Alarm Mode

Using the Alarms

You can set up to five independent daily alarms. An alarm sounds
for 10 seconds when an alarm time is reached.
❚ To view the alarm time or target alarm time
In the Alarm Mode, press the B B B B B button to cycle through
the alarm screens in the sequence shown below.
• The alarm number appears first, followed by the current alarm
time setting.
Alarm Time
Alarm Number
Alarm 1 Alarm 2 Alarm 3
(AL1) (AL2) (AL3)
Hourly Time
Snooze Alarm Target Alarm
Signal
(AL5) (AL4)
(:00)
5.
Use the D D (+) and B D D D B B (–) B B
buttons to change the
minute setting.
• Holding down either button
scrolls the setting at high
speed.
6.
When setting is the way
you want, press the A A A A A
button.
• This exits the setting screen.
• The alarm you set is turned
on automatically whenever
you change its settings.
• The display also will exit the
setting screen automatically if
you do not perform any
operation for about two or
three minutes.
Operation Guide 2763
Types of Alarms
• Daily Alarms (AL 1, AL 2, AL 3)
The watch beeps for 10 seconds when the alarm time is
reached.
• Target Alarm (AL 4)
With a target alarm, the time remaining until the alarm time
counts down on the display. The watch beeps for 10 seconds
when the alarm time is reached.
• Snooze Alarm (AL 5)
With the snooze alarm, the watch beeps for 10 seconds when
the alarm time is reached, and up to seven times at
five-minute intervals thereafter. Pressing any button stops the
beeper, but the alarm will sound again after five minutes.
About the Target Alarm Time Screen
When your turn on the target alarm (AL 4), the display shows the
alarm time momentarily and changes to show how much time
remains until the target alarm time.
Alarm Number Alarm Time
❚ To turn an alarm on or off
(Back)
1.
B B
In the Alarm Mode, use the B B B button to display the
screen for the alarm (AL 1 through AL 5) you want to
turn on or off.
2.
(Forward)
Press the A A button to toggle the displayed alarm on or A A A
off.
• Turning on an alarm also causes its "on" indicator to appear.
The snooze alarm screen also has a snooze indicator (SNZ).
Alarm 1 Screen Snooze Alarm Screen
Snooze Indicator
Shows "on" when the alarm is on.
Shows "oF" when the alarm is off.
• Note that the "on" and "oF" indicators appear in the Alarm
Mode only. The snooze indicator (SNZ) remains on the display
in all modes.
❚ To set an alarm time
1.
In the Alarm Mode, use the
B B B B button to scroll B
through the alarm screens
(AL1 to AL5) until the one
you want is displayed.
2.
Hold down the A A A A button A
for about two seconds
until the hour digits of the
alarm time start to flash.
• This is the setting screen. At
this time the displayed alarm
turns on automatically. If you
have the snooze alarm
displayed (AL 5), the snooze
indicator (SNZ) also appears
at this time.
Remaining Time
❚ Stopping the Alarm Beeper
Pressing any button while the beeper is sounding stops it.
• In the case of the snooze alarm the alarm will sound again in
about five minutes. The snooze indicator flashes while the snooze
alarm is active (indicating that the alarm will sound again).
• The snooze alarm will be canceled automatically when any of the
following occurs while the SNZ indicator is flashing on the display.
• If you turn off the snooze alarm in the Alarm Mode
• If you enter the Alarm Mode, display the snooze alarm screen,
and then display the setting screen.
• If you enter the Timekeeping Mode and then display the setting
screen.
❚ To test the alarm
In the Alarm Mode, hold down the B button to sound the alarm.
3.
D D D (+) and B B B B (–)
Use the D D B
buttons to change the
hour setting.
• Holding down either button
scrolls the setting at high
speed.
• When setting the hour, make
sure you specify AM (no
indicator) or PM (P) correctly
when using 12-hour
timekeeping, or that you
specify the correct 24-hour
Hour
time.
• Alarm mode times are
displayed in the same format
(12-hour or 24-hour) that you
selected in the Timekeeping
Mode.
4.
C C
Press the C C C button so the
minute setting flashes.
Using the Hourly Time Signal
The hourly time signal causes the watch to beep every hour on the
hour.
❚ To turn the hourly time signal on and off
1.
In the Alarm Mode, use the B
screen for the hourly time signal (SIG:00).
2.
A button to toggle the hourly time signal on A A
Press the A A
or off.
• Turning on a the hourly time signal causes its "on" indicator to
appear.
Hourly Time Signal Screen
Shows "on" when the hourly time signal is on.
Shows "oF" when the hourly time signal is off.
• Note that the "on" and "oF" indicators appear in the Alarm
Mode only.
(Back)
(Forward)
Minute
B button to display the B B B
7