HISTORY INFORMATION FOR THE FOLLOWING MANUAL: EX2K SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KDL-26L5000 RM-YD028 KDL-26L5000 RM-YD028 CANADA KDL-26L5000 RM-YD028 MEXICO KDL-32L5000 RM-YD028 KDL-32L5000 RM-YD028 CANADA KDL-32L5000 RM-YD028 MEXICO ORIGINAL MANUAL ISSUE DATE: 12/2008 REVISION DATE SUBJECT 12/2008 No revisions or updates are applicable at this time.
Page 2
EX2K SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KDL-26L5000 RM-YD028 KDL-26L5000 RM-YD028 CANADA KDL-26L5000 RM-YD028 MEXICO KDL-32L5000 RM-YD028 KDL-32L5000 RM-YD028 CANADA KDL-32L5000 RM-YD028 MEXICO KDL-32L5000 RM-YD028 LCD DIGITAL COLOR TELEVISION 9-883-809-02...
A Board Schematic Diagram (9 of 17) ........33 1-6-1. Brackets and Spine Removal A Board Schematic Diagram (10 of 17) ........ 34 (KDL-26L5000 Only) ..........16 A Board Schematic Diagram (11 of 17) ........ 35 1-6-2. Brackets and Spine Removal A Board Schematic Diagram (12 of 17) ........
Components identifi ed by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identifi...
Les composants identifi es par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de pieces sont d’une importance critique pour la securite du fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony.
KDL-26L5000/32L5000 SAFETY-RELATED COMPONENT WARNING There are critical components used in LCD color TVs that are important for safety. These components are identifi ed with shading and mark on the schematic diagrams and the electrical parts list. It is essential that these critical parts be replaced only with the part number specifi...
Page 9
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com KDL-26L5000/32L5000...
KDL-26L5000/32L5000 SAFETY CHECK-OUT The AC leakage from any exposed metal part to earth ground and After correcting the original service problem, perform the following from all exposed metal parts to any exposed metal part having a safety checks before releasing the set to the customer: return to chassis, must not exceed 0.5 mA (500 microamperes).
KDL-26L5000/32L5000 SELF-DIAGNOSTIC FUNCTION The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED indicator will automatically begin to fl ash. The number of times the LED fl ashes translates to a probable source of the problem. A defi nition of the STANDBY LED fl ash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 12
KDL-26L5000/32L5000 LED Indicators 1. TV must be in standby mode. (Power off). 2. Press the following buttons on the Remote Commander within a second of each other: Channel 5 Volume - TV POWER . DISPLAY The Self Check list displays.
KDL-26L5000/32L5000 SECTION 1: DISASSEMBLY 1-1. REAR COVER REMOVAL Remove 12 screws from Rear Cover Remove 1 screw from Side Jack position Remove 2 screws from Terminal position Remove 2 screws from Rear Cover 1-2. SWITCH UNIT REMOVAL (CONTAINS H1 BOARD)
KDL-26L5000/32L5000 1-3. A BOARD AND G2BE (POWER SUPPLY) BOARD REMOVAL Lift top and bottom latches from Side Jack Bracket to unhook from Main Bracket Disconnect 7 connectors from A Board Main Bracket Side Jack Cover Remove 9 screws from A Board...
KDL-26L5000/32L5000 1-6. BRACKETS AND SPINE REMOVAL 1-6-1. BRACKETS AND SPINE REMOVAL (KDL-26L5000 ONLY) Remove 1 screw from Main Bracket and Bezel Remove 2 screws from Main Bracket and LCD Panel Main Bracket Remove 2 screws from Spine Remove 1 screw from Bottom Bracket...
KDL-26L5000/32L5000 1-7. H2 BOARD AND LCD PANEL REMOVAL Disconnect LVDS connector from T-con Remove 2 screws from bottom of panel and release LCD panel from Bezel Disconnect 1 connector from Inverter Board Disconnect 1 connector from H2 Board Remove 1 screw from H2 Board...
KDL-26L5000/32L5000 1-8. BALANCER (MT INVERTER) BOARD REMOVAL (KDL-26L5000 ONLY) Remove 6 screws from Board cover Pull out the Board from Lamp socket LCD Panel Cover Balancer Board REMOVE SCREWS SECURING SHIELD REMOVE CONNECTOR AND PULL BOARD TO THE RIGHT INVERTER BOARD REMOVAL Only remove the screws securing the inverter cover which may be metal or plastic.
KDL-26L5000/32L5000 SECTION 2: SERVICE ADJUSTMENTS 2-1. VIEWING SERVICE ADJUSTMENT DATA There are no adjustments necessary for these models. All data has been set for optimal viewing for our customers. The following sections are for informational purposes only. 2-2. ACCESSING SERVICE ADJUSTMENT MODE 1.
KDL-26L5000/32L5000 SECTION 3: DIAGRAMS 3-1. CIRCUIT BOARDS LOCATION 3-2. PRINTED WIRING BOARDS AND All voltages are in V. SCHEMATIC DIAGRAMS INFORMATION S : Measurement impossibility. : B+line. All capacitors are in μF unless otherwise noted. pF : μμF 50WV or : B-line.
Page 23
KDL-26L5000/32L5000 REFERENCE INFORMATION Terminal name of semiconductors in silk screen printed circuit ( RESISTOR CAPACITOR : RN METAL FILM : TA TANTALUM Circuit Device Printed symbol Terminal name : RC SOLID : PS STYROL Collector Transistor : FPRD NONFLAMMABLE CARBON...
SCREW, +PSW M5X16 (KDL-26L5000(US/CND) ONLY) (SCREWS TO ATTACH TABLE-TOP STAND TO LCD TV) 4-133-596-01 LABEL, INFORMATION (26 MX) For product protection and safety reasons, Sony strongly recommends (KDL-26L5000(MX) ONLY) that you use the screws provided with the TV 4-132-198-01 LABEL, INFORMATION (32)
ONLY) with part number specifi ed. numero specifi e. See Appendix A: Encryption Key Components in the back of this manual. 4-2. CHASSIS (Check the Sony Electronics Service Information website for any additional service related issues for this model.) 4-382-854-01 SCREW, +PSW M3X8 REF. NO.
See Appendix A: Encryption Key Components in the back of this manual. 4-3. BEZEL ASSEMBLY AND LCD PANEL (Check the Sony Electronics Service Information website for any additional service related issues for this model.) 7-685-662-29 SCREW, +BVTP2 4X14...
Page 53
AC POWER SUPPLY CORD WITH CONN (SCREWS TO ATTACH TABLE-TOP STAND TO LCD TV) 3-876-008-01 BAG, PROTECTION (40) For product protection and safety reasons, Sony strongly recommends 3-876-009-01 BAG, PROTECTION STAND (40) that you use the screws provided with the TV.
MUST BE RETURNED to Sony. b) and if the core charge is NOT covered under the product warranty, the defective un-repaired or modifi...
Page 55
In an effort to reduce the size of this pdf fi le the tiled schematics are not attached to this Service Manual. To receive a complete set of the tiled schematics for this manual please submit a request to the Service Promotion Department at Service_Promotion@am.sony.com.