Related Manuals for EarthQuake 7055 6 HP BRIGGS
Summary of Contents for EarthQuake 7055 6 HP BRIGGS
-
Page 1: Operating Instructions
OPERATING INSTRUCTIONS & PARTS EXPLOSIONS SRT ROTOTILLERS 7055 6 HP BRIGGS 7155 6 HP BRIGGS 7065V 6.5 HP VIPER ARDISAM .com OMSRT07 Rev. 2/5/07 © Copyright 2007 Ardisam, Inc. All Rights Reserved. Printed in USA. -
Page 2: Table Of Contents
SRT Models INTROdUCTION WARRANTY ThANk YOU . . . for purchasing an Earthquake® forward rotating rear-tine rototiller ONE YEAR lImITEd WARRANTY from Ardisam, Inc. We have worked to ensure that this rear-tine The Ardisam, Inc., Manufacturing Company warrants rototiller meets high standards for usability and durability. With proper this rototiller to be free from defects in material or care, your rototiller will provide many years of service. -
Page 3: Safety
• Carefully follow all assembly instructions. • Maintain the tiller according to directions and schedule included WARNING in this Earthquake operator’s manual. WARNING INdICATES A SERIOUS INjURY OR FA- • Ensure that anyone who uses the tiller is familiar with all TAlITY COUld RESUlT IF ThE SAFETY INSTRUC- controls and safety precautions. -
Page 4: Maintenance And Storage
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models c. Fill fuel tank outdoors with extreme care. Never fill fuel ImPORTANT tank indoors. ThE RIGhT ANd lEFT SIdES OF d. Replace gasoline cap securely and clean up spilled fuel YOUR ROTOTIllER ARE dETER- before restarting. -
Page 5: Safety
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models SAFETY dECAlS This rototiller unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing. Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operated this equipment safely and effectively, we have placed several safety labels on the tiller to remind you of this important information while you are operating the unit. -
Page 6: Unpacking And Assembly
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models UNPACkING ANd ASSEmBlY ImPORTANT Your rototiller comes fully assembled except for a few parts. The fol- ThE RIGhT ANd lEFT SIdES OF YOUR lowing instructions will help you unpack your tiller and assemble and ROTOTIllER ARE dETERmINEd FROm adjust your tiller’s depth regulator lever, cable tension and handlebar ThE OPERATING POSITION AS YOU... -
Page 7: Features
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models FEATURES All SRT mOdElS forward drive safety control lever reverse drive safety control lever forward & reverse cable bumper guard (Model 7155 ) depth regulator lever detent pin belt guard wheel lock pin (Model 7055, 7065V) or wheel lockout (Model 7155) recoil start serial number plate... -
Page 8: Operation
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models OPERATION CAUTION PRE-START INSPECTION PlEASE dO NOT START YOUR TIllER UNTIl YOU hAvE REAd ThE mANUAl ThAT CAmE 1. Make sure all safety guards are in place and all nuts and bolts WITh YOUR ENGINE, ANd ThE SECTIONS IN ThIS are secure. -
Page 9: Operation
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models IdlE SPEEd WARNING Use the “low” position on the throttle lever to reduce stress on the TEmPERATURE OF mUFFlER ANd NEAR BY AREAS engine when tilling is not being performed. Lowering the engine speed mAY ExCEEd 150°... -
Page 10: Drive Safety Control Levers
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models dRIvE SAFETY CONTROl lEvERS CAUTION FORWARd lEvER dO NOT OPERATE BOTh “FORWARd” ANd Engages wheels and tines into forward. “REvERSE” dRIvE SAFETY CONTROl lEvERS AT Pulling the drive safety control lever labeled (FORWARD) toward the ThE SAmE TImE. -
Page 11: Handlebar Height Adjustment
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models WhEEl lOCk PINS (7055, 7065v) WARNING Place wheels in tilling position. NEvER START ENGINE OR OPERATE TIllER WITh 1. Remove lock pin. Align hole in axle with hole in wheel hub. WhEElS IN FREE-WhEEl POSITION. ThE FREE- 2. -
Page 12: Depth Regulator Lever
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models dEPTh REGUlATOR lEvER WARNING Tilling depth is controlled by the height of the depth regulator lever. dO NOT AdjUST TIllING dEPTh UNlESS dRIvE To adjust tilling depth. SAFETY CONTROl lEvERS ARE RElEASEd TO 1. -
Page 13: Tilling Tips
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models TIllING TIPS WARNING The key to successful tilling is to begin with a shallow cut on the ExTREmE CAUTION mUST BE TAkEN IN SElECT- first pass, and then work an inch or two deeper on each successive ING TIllING dEPTh. -
Page 14: Maintenance & Storage
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models mAINTENANCE ANd STORAGE mAINTENANCE SChEdUlE Your rototiller has been designed and produced by the industry’s leading manufacturer of outdoor power equipment to provide you with years of reliable operation. Keeping your tiller in top running condition will prolong its life, and help you obtain optimum performance. Please read this normal care schedule, and note the recommended care operating intervals to extend the life of your unit. - Page 15 OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models ChANGE FORWARd/REvERSE BElT CAUTION 1. Turn off engine. Engine must be cool. dO NOT OPERATE TIllER BEFORE REAdING 2. Remove spark plug wire and secure from spark plug. ThE ENGINE mANUAl PROvIdEd IN ThE PARTS 3.
-
Page 16: Engine Maintenance
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models ENGINE mAINTENANCE ImPORTANT Refer to the engine manual included in your parts packet for information on engine maintenance. Your engine manual provides ENGINE IS ShIPPEd FROm FACTORY WIThOUT OIl. detailed information and a maintenance schedule for performing the YOU mUST Add ENGINE OIl BEFORE STARTING following tasks: ENGINE. -
Page 17: Clean Tine Axle Shaft
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models lUBRICATION WARNING Proper lubrication of moving mechanical parts is critical for proper dO NOT STORE TIllER IN AN UNvENTIlATEd care and maintenance. Oil the moving parts shown at 10 hour intervals AREA WhERE FUEl FUmES mAY REACh FlAmE, using a 30 weight oil. -
Page 18: Troubleshooting And Repair
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models TROUBlEShOOTING ANd REPAIR WARNING TROUBlEShOOTING GUIdE PRACTICE SAFETY AT All TImES. ENGINE mUST BE While normal care and routine maintenance will extend the life of TURNEd OFF ANd AllOWEd TO COOl, ANd SPARk PlUG WIRE mUST BE dISCONNECTEd ANd SECUREd your rototiller, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. - Page 19 OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models PROBlEm REmEdY/ACTION Belts squeal in neutral and/or reverse • Adjust forward belt guide: - turn engine off and allow muffler to cool - disconnect spark plug wire and secure from spark plug - remove belt guard - pull down on drive safety control levers - manually bend forward belt guide so there is 1/16 inch or less clearance between belt guide and belt...
-
Page 20: Parts Explosions
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models SRT hANdlEBAR PARTS ExPlOSION 53650(2) 53632 53614 53631(2) 53613 53612 53606(2) 53620 53607(4) 53629 60G56 53630(2) 53624 2104(4) 53679 90139(2) 53618(2) 90138(4) 48762(2) 2104(2) Page 0 800-345-6007... - Page 21 OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models SRT hANdlEBAR PARTS lIST PART # dESCRIPTION QTY. 2104 Nut Hex Two-Way 3/8-16 48762 Bolt 3/8-16 x 1” Carriage Bolt 5/16-24x1” HH GR5 53606 Nut-Nyloc, #10 53607 Nut-Jam, 5/16-24 53612 Link 11-5/8” long 53613 Link 9-1/2”...
- Page 22 OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models SRT TINES & hOOd PARTS ExPlOSION 509(2) 415A 504(2) 417(2) 1504(2) 1501(4) 1900LCRT 69170 53699 1501(2) 1511(3) 1508 1507 2001(2) 1900RCRT 719(2) 2104(2) 1103(2) 1501 1710(2) 1500L, 1500P 53698 1507 1514 1515 48406 53640 1516(3) Models 7155...
- Page 23 OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models SRT TINES & hOOd PARTS lIST PART # dESCRIPTION QTY. PART # dESCRIPTION QTY. 1103 Lock Pin 5/16” x 1-3/4” Tail Mount Depth Regulator 1103A Wheel Lockout Knob (7155) 415A Hood Assembly 1103B Butterfly Lockout (7155) Bolt 5/16-18 x 1/2”...
- Page 24 OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models SRT mOTOR mOUNT PARTS ExPlOSION 2104 1408 WF38(2) 53638 53682 53649 48144B 1423(4) 53622 WF516 (4) 53617 60501, 60365 53637 WF516 WF516 2104 1408 WF38(2) 48144B 504(2) 1416 WF516 1418 53696B WF516 802(2) 741, 742 504(2) 1407(2)
- Page 25 OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models SRT mOTOR mOUNT PARTS lIST PART # dESCRIPTION QTY. PART # dESCRIPTION QTY. 1407 Forward Arm Spring 53648 Bumper Guard (7155) 1408 Forward Pulley Idler 53649 Belt Guard 1416 Clevis Pin 53682 Reverse Tine Weldment 1418 Cotter Pin 5/64”...
- Page 26 OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models SRT WhEEl & TIllER ShAFT PARTS ExPlOSION & PARTS lIST PART # dESCRIPTION QTY. PART # dESCRIPTION QTY. 1500L Transmission Complete, Lockout 1801 Tine Shaft (7155) 1803 Gear-Worm, Brass, 30 Tooth, Tiller 1500P Transmission Complete, Lock Pin Shaft 1506...
-
Page 27: Parts Explosions
OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS SRT Models 000 hIllER/FURROWER kIT INSTAllATION (OPTIONAl ACCESSORY)* Thank you for purchasing a hiller/furrower attachment for your rototiller. You will be pleased with the many work saving uses you can accomplish with this handy tool. To assemble, attach furrower to bracket and then wings to furrower. -
Page 28: Cumberland, Wisconsin
ARDISAM .com Visit www.ardisam.com and discover more innovations that will benefit you throughout the year. Earthquake, Division of Ardisam, Inc. 1690 Elm Street; P.O. Box 666 Cumberland, Wisconsin 54829 800-345-6007 · Fax (715) 822-2223 E-mail: info@ardisam.com...