Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Conrad CARRY HDD PRO318
-
Page 1: Hdd Duplicator
V 2.0 PRO318 (1-3) HDD Duplicator User Guide 2014/10/5... -
Page 3: Table Of Contents
Content How to Erase HDD? Content 1. How to Erase? Product Introduction 2. Setting of Erase Function 1. Features Quick Erase 2. Product Overview Full Erase A. System Overview DoD Erase B. LCD Configuration DoD EraseComp 3. Select Random Pattern Function Table Overwrite by Fixed Method Function Table... -
Page 4: Product Introduction
1 Product Introduction 1. Features • High copy speed supports up to 6.6GB/min. • Auto power control to protects your HDD.(HDD only powered during operation.) • Support 2.5" and 3.5" SATA HDD, IDE HDD and SSD. (IDE HDD needs convertor) •... -
Page 5: Product Overview
Product Introduction 1 2. Product Overview A. System Overview Red : Fill Port 1 Flashing Green : Operating (Source) Remain Green : Pass Yellow : Power Supplying Port 4 (Target 3) Port 2 Port 3 (Target 1) (Target 2) B. LCD Configuration Total Size Function Target HDD... -
Page 6: Function Table
2 Function Table Function Table Function Description 1. Copy Copy data from source HDD to targets. (there are four copy modes for selection at function 6.1) 2. Compare Comparison between the source and targets to make sure copy accuracy. 3. Copy+Compare Execute compare function automatically after copy. - Page 7 Function Table 2 6.4.2.1 Disable 6.4.2 Erase Master Disable erase source HDD. Setup to erase source HDD or 6.4.2.2 Enable not. Enable erase source HDD. 6.4.3.1 ONE Byte A random character to be written into every byte. 6.4.3 Erase Pattern 6.4.3.2 Big Random Data 6.4 Advanced Setup A set of random character to be...
-
Page 8: How To Start Duplicating Hdd
3 How to Start Duplicating HDD How to Start Duplicating HDD? 1. Start Duplication Step 1 Prepare a source HDD and target HDD (*It is strongly recommended to the size of source and target are the same) Source HDD Target HDD Note ㅦ... -
Page 9: Set-Up Before Start Duplication
How to Start Duplicating HDD 3 Step 3 Use ▲▼ to select "1. Copy" then press "OK". Duplication will proceed. Note When all the target HDD ports are plugged, duplicator would start copying automatically. If not all are plugged, the number of targets shows on LCD. Press "OK" to start. The information below shows on LCD during duplication. -
Page 10: System And Files
3 How to Start Duplicating HDD System and Files (Quick Copy or Compare) It will copy source HDD's System and Files instead of the whole HDD. The system will analyze the source HDD and identify the data area to copy. As long as the source HDD's data within the target HDD's space, the copy will be processed. -
Page 11: Whole Hdd
How to Start Duplicating HDD 3 Source Duplication Target Partition 1(150G) Data 30G Partition 1(200G) Data 90G 500GB 500GB Only 350 GB partition area will be copied, it takes 48 mintues. Note Duplication time is affected by "transfer speed of HDD". Whole HDD It is to copy the whole source HDD, no matter of the content, format, partition or empty space. -
Page 12: Percentage(%)
3 How to Start Duplicating HDD Percentage(%) Copy the percentage selected of source HDD. Note Duplication time is affected by "transfer speed of HDD". Below is one example of copy area selection e.g. There are two partitions in one 500GB HDD. Data and OS(120GB) are saved in the partition. Note ㅦ... -
Page 13: ❷ Set Tolerance Of Bad Track
How to Start Duplicating HDD 3 ❷ Set Tolerance of Bad Track Select function 6.2 Skip Error to set the number of error you accept to skip during copy process. If the HDD is very critical for content correctness, it is strongly recommended to keep the Skip Error to be "0". -
Page 14: How To Confirm Copy Accuracy
4 How to Confirm Copy Accuracy? How to Confirm Copy Accuracy? 1. To Confirm Accuracy by Compare Function Step1 Prepare source HDD and target HDD. Source HDD Target HDD Step 2 Place source HDD at source port, targets HDD to other ports. Step 3 Use ▲▼... -
Page 15: Setting Of Compare Function
How to Confirm Copy Accuracy? 4 2. Setting of Compare Function It is able to set compare area of HDD at function 6.1 There are four different compare area for selection : ① System and Files, ② All available partition area, ③ Whole HDD, ④ Percentage Compare. Note It is recommended to execute Compare after Copy to confirm the accuracy. -
Page 16: How To Erase Hdd
5 How to Erase HDD? How to Erase HDD? Note Please notice the data within the HDD will be erased after executing the function. 1. How to Erase? Step1 Prepare the HDD for erasure. Step 2 Insert the HDD into target port. Note Function 6.4.2 Erase Master is to determine erase source HDD or not. -
Page 17: Setting Of Erase Function
How to Erase HDD? 5 Step 3 Use ▲▼ to select the desired erase method, then press "OK". Data Erase will proceed. 2. Setting of Erase Function There are four erase methods: Quick Erase, Full Erase, DoD Erase, and DoD EraseComp. Quick Erase The function will ONLY erase the index of the HDD. -
Page 18: Dod Erase
5 How to Erase HDD? DoD Erase This is to comply with the U.S.A. Department of Defense (DoD 5220) standard to fully erase the HDD three times bit by bit to rewrite HDD to guarantee the data was deleted. It will damage the data in HDD, please make sure you have backup all important data before using this function. -
Page 19: Select Random Pattern
How to Erase HDD? 5 3. Select Random Pattern Overwrite by Fixed Method Overwrite by Random Method... -
Page 20: Update Bios
6 Update BIOS Update BIOS 1. How to Update BIOS? ※ Update by HDD Step 1 Prepare one HDD and connect it to source port, then select function 5.2.2 Create update HDD. Step 2 Format the HDD. Note ㅦ Before updating firmware, one FAT, 2GB partition will be formatted in the HDD. That would reduce searching time, and speed up firmware update. - Page 21 Update BIOS 6 Step 4 Insert HDD into source port (first port), select function 5.2.1 Update BIOS. Update would complete in one minute.
-
Page 22: Specification
Specification Specification Product Name Carry Mini HDD Dupe Product Number PRO318 Targets HDD Interface SATA, IDE(optional) Display 2x16 Monochrome LCD Control Button 4 push buttons Compatible HDD All major brand of 2.5",3.5" SATA and IDE HDD and SATA SSD 1. System and Files 2.