INSTRUCTION MANUAL Thank you for purchasing this product. For correct use and application, please read this instruction manual thoroughly. SV-420 / SV-430 REAR-VIEW SYSTEM FOR VEHICLE PRINTED IN KOREA * Design and specifi cations could be changed without notices. ver. 1.0...
SAFEGUARD INSTRUCTIONS REAR-VIEW SYSTEM FOR VEHICLE Please pay attention to the warnings and cautions listed in order to prevent the potential risks. “WARNING” and “CAUTION” symbols are divided according to the different level of risk. This information is for preventing damage or shorten the life time of the products.
Page 4
WARNING Do not put the product in place where sudden temperature increasing and should use on optimum voltage, temperature and humidity. Do not place near of air bag effective range. - It may cause malfunction of air bag or accident, injury due to hitting monitor by air bag. Keep clean dust on power socket.
FUNCTION OF EACH PART REAR-VIEW SYSTEM FOR VEHICLE [ CM-430 MONITOR ] 4.3” TFT LCD (480x272) 1. Display 5. Speaker Max. 0.5W(MONO) 2. MENU Menu setting and change 6. Cable Guidance 3. Volume Volume setting 7. Bracket Stand Bracket connect part 4.
FUNCTIONS REAR-VIEW SYSTEM FOR VEHICLE [ CM-430 MONITOR ] 1. Power ON/OFF 1) POWER ON : If you push, POWER ON. (STAND BY state is OFF) 2) POWER OFF : If you push again, POWER OFF. 2. Button function MENU button The menu changes [BRIGHTNESS] - [CONTRAST] - [COLOR] - [TINT] - [DIMMER] - [LANGUAGE] - [MONITOR] - [RESET] every push [MENU] button.
Page 8
·[COLOR] : Density adjusting on screen color On Color setting mode, △▽ buttons control density of screen color. (0~100) [0 : Low density / 100 : High density] COLOR ·[TINT] : Screen color adjusting On Tint setting mode △▽ buttons control screen color. (0~100) TINT ·[DIMMER] : Automatic brightness adjusting On Dimmer setting mode, the menu changes [DAY] - [NIGHT]...
INSTALLATION REAR-VIEW SYSTEM FOR VEHICLE MONITOR INSTALLATION 1. Remove protecting tape from below of stand and attach stand with double stick tape. 2. Fix a stand with enclosed 3 screws. 3. Connect stand and monitor.
Page 10
SV-420 CAMERA INSTALLATION (CM-200) 1. Determine a position and direction of instal- lation and attach a camera bracket using double stick tape and screws. 2. Connect a camera and sun visor with bracket on vehicle and fix them with screws.
CABLE CONNECTION REAR-VIEW SYSTEM FOR VEHICLE [ CM-430 MONITOR ] CM-200 CM-36 Extension Cable (for Camera) CAMERA Extension Cable (for CAMERA) Monitor Cable Extension Cable (for TRG) DC IN (12V~24V) Before making the connection, disconnect the ground terminal of the car battery to avoid short circuiting.
SPECIFICATION REAR-VIEW SYSTEM FOR VEHICLE CM-430 (MONITOR) <LCD Panel> LCD size 4.3” Image ratio 16 : 9 Resolution 480 x 3(RGB) x 272 Brightness 400cd Contrast range 600 : 1 Active area 95.04(W) x 53.86(H) mm Viewing angle 80(L) / 80(R) / 65(T) / 52(B) <Monitor>...
Page 13
CM-200 (CAMERA) Image sensor 1/3” 960H color CCD Viewing angle 168(D) / 125(H) Min. Illumination 0.1Lux (F=2.0) Resolution 700 TV Lines Operating voltage DC12V / 90mA Operating temperature -30°C ~ 70°C Dimension 36.6(W) x 27(H) x 38.2(D) mm Weight 80g (Body only) CM-36 (CAMERA) Image sensor 1/3”...
Need help?
Do you have a question about the SV-420 and is the answer not in the manual?
Questions and answers