FlEXSYS F212 User Manual page 6

Object and Liquid Entry
The apparatus must be placed in inappropriate position. Care should be taken so that objects do not
fall and liquids are not spilled into the enclosure through cooling grid with consequent electrical
danger.
Ventilation
The appliance should be situated so that its location or position does not interfere with its proper
ventilation. Do not block or cover any openings of the grid ventilation or heatsink. Install the apparatus
at a distance that ensures a good ventilation between devices.
Heat
Do not install the appliance near any source of heat.
Accessories and installation
For a safe installation, do not make any holes in the external chassis for the application of additional
brackets. In case of particular installations not described in this manual, contact technical service for
accessories specified by the manufacturer.
Follow the instructions
All operations and instructions in this user manual should be followed for a correct operation and
function of appliance. Pay attention in particular to:
- Never force the control elements (switches, controls, etc.).
- Do not force the amplifier to work in overload for extended periods of time.
Cleaning
Clean only with a dry cloth. Do not use solvents, alcohol, benzene or volatile substances for cleaning
the exterior parts.
CONNECTION
CAUTION
- For connecting the appliance, use only qualified and experienced personnel having sufficient
technical knowledge or specific instructions for making the connections correctly and thus
preventing electrical dangers.
- To prevent the risk of electrical shock, the appliance must only be supplied from the mains after
all connections have been completed.
- Before powering up the appliance, it is advisable to re-check all the connections.
- The entire sound system must be designed and installed in compliance with the current
standards and regulations regarding electrical systems.
SUGGESTIONS
CAUTION
To prevent inductive phenomena from giving rise to hum or disturbance which would jeopardize
efficient appliance operation, the cables that transmit microphone signals or line level signals (e.g. 0
dB/V) must be screened and should not be run in the vicinity of:
1) Equipment that produces strong magnetic fields (e.g. large power supply transformers)
2) Electrical energy conductors
3) Lines that supply speakers.
9
DESCRIPTION
The FLEXSYS series bi-amped speakers are equipped with
®
DIGIPRO series class D amplifier. This high-efficiency
amplifier delivers high output power in a compact size at low
weight. Thanks to its high efficiency the cooling of the
amplifier module is obtained statically, thus avoiding the use
of a fan.
The power supply circuits of the DIGIPRO amplifier has
been conceived to work in full-range mode; thanks to the
SMPS (Switched-Mode Power Supply) technology with PFC
(Power Factor Correction) the operation with supply voltages
between 100 Vac and 240Vac is guaranteed by ensuring the
same sound performances even with floating and non-
stabilized power supply systems.
FLEXSYS F212 (2 ways)
The F212 bi-amped active speaker is equipped with a
®
DIGIPRO amplifier which delivers 500W RMS for the bass
section and 250W RMS for the high frequency section.
The F212 active two-way speaker features two 12" (voice coil
2.5") woofers and a neodymium 1"(voice coil 1.75")
compression driver. The phase plug attached to the front of
the upper 12" woofer avoids the vertical phase modulation
which usually take place in this type of configuration and
ensures a precise horizontal coverage of the medium
frequencies.
The speaker is made of 15mm birch ply wood, the 4 handles,
the 12 M10 threads located on the sides and the back of the
speaker are enabling easy transport and installation.
The trapezoidal-shaped housing (20° angle) allows the side-
by-side setup of several speakers in cluster configuration. For
side-by-side installation, the horn must be turned (40° x 60°)!
The bottom features a adjustable foot (in height) to inclinate
the tilt angle up to a max. of 5°. This allows to direct the sound
radiation without using additional supports.
In the bottom of the box there is a standard pole mount cup
(D36mm) made of aluminium
FLEXSYS F315 (3 ways)
The F315 active speaker is equipped with a DIGIPRO
amplifier delivering 500W RMS for the bass section featuring
a 15" woofer (voice coil 3") and 500W RMS for the mid-high
section featuring a passive filter driving a 6" midrange (voice
coil 2") and a 1" compression driver (voice coil 1.5").
The speaker is made of 15mm birch ply wood, the 4 handles,
the 12 M10 threads located on the sides and the back of the
speaker are enabling easy transport and installation
The 15" woofer and the midh-high section with horizontal 90°
coverage is the ideal solution for all demanding full-range
applications .
In the bottom of the box there is a standard pole mount cup
(D36mm) made of aluminium
®
®
10