Using your GP-20’s Electrocouplers Using your GP-20’s magnetic uncouplers A note on Magne-Traction Your GP-20’s Railsounds system—the basics Experiencing the range of your GP-20’s Railsounds system Notes on Railsounds Installing the Lionel no. 610-5906-001 sound activation button TrainMaster Command operations...
GP-20 on track while passing swiftly through curves. Power up your GP-20 with your transformer. • Your GP-20 is designed to operate on 7-18 volts alternating cur- rent. Virtually all Lionel and Lionel-compatible alternating-current transformers are suitable; we recommend the TrainMaster Command model railroad control system.
Note! open manually or by using a remote-con- trol track section Remote-control track section Using your GP-20’s Electrocoupler in the TrainMaster Command environment button on your CAB-1 remote, and that f your Lionel GP-20 is equipped with coupler opens. front and rear Electrocouplers it...
SIGNAL position illustration on before powering up page 13 for their Install a 9-volt alkaline battery in your GP-20. Remove the the locomotive. See location), lift off four mounting crews, lift off the body, connect the battery page 12 for the GP-20’s...
Transformer operations Experiencing the range of your GP-20’s Railsounds system within 3 seconds, decrease track voltage ith Railsounds, you experience to the desired speed level, press DIR on the sounds of real railroading your CAB-1 remote or transformer, and like never before. Simply put, it’s the...
(for bell) (for horn) The no. 610-5906-001 sound activation button (available separately) works with any Lionel AC transformer except no. 6-4690 Type MW. Note! Transformers made by other manufacturers may not be compatible with Railsounds.
• All Command-equipped Lionels come factory-programmed with an ID# of “1.” To change the ID# of your GP-20, see page 12. Move ‘em out! • Throttle up or press any command button on CAB-1. Your GP-20...
Running your GP-20 in the TrainMaster Command environment our Command-equipped GP-20 Example address Locomotive #1 locomotive comes factory-pro- grammed with an ID# of “1.” To get PowerMasters set to CMD or traditional your GP-20 locomotive in action, set power supplies ON FULL PowerMasters to CMD or set all power supplies on full.
TARTUP SEQUENCE COMMENCES Lowers the volume of Rail- Turns strobe light off. sounds. S OUND VOLUME DECREASES Activates the Railsounds shut- Turns strobe light on. down sequence. Just like the real thing, your GP-20’s RPMs must be at idle for...
For quick remote-control of volume SET; the GP-20 will stop. The head- below the master setting—like mut- light will flash, indicating it’s in the ing—use the CAB-1 numeric key- SET mode.
Maintaining and servicing your GP-20 locomotive Lubricating your GP-20 locomotive grease or oil on the GP-20’s wheels, elp your Lionel GP-20 locomotive contact rollers, or your track. lead a long and productive life on You’ll know your GP-20 requires your railroad by maintaining it properly.
Maintaining and servicing your GP-20 locomotive Lubricating your GP-20’s Pullmor motor armature shaft hole. our GP-20 locomotive will require Finish the job by reinstalling the occasional lubrication of its Pullmor body shell and reinserting the four cab motor armature. If you hear excess noise mounting screws.
Replacing your GP-20’s lamps connected to the shell. our GP-20 locomotive is illuminat- Locate the assembly containing the ed by two 12-volt lamps. One illu- expired lamp. It’s held in position by a minates the rear lights and the other illu- retaining clip;...
Website @ www.Lionel.com motors and structural components, except for If you prefer to send it back to Lionel L.L.C. for light bulbs, is warranted to the original con- factory repair, you must first call 810-949-4100 or...