Bosch GPO 12 CE Professional Original Instructions Manual page 24

24
| English
d. Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e. Maintain power
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
5) Service
a. Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
b. If the power cord is damaged, the power
cord shall be replaced by manufacturer,
service or qualified person to avoid the risk
of electrical shock.
c. In case of consuming of the carbon brushes
to send the tool by assistance authorized
technique for substitution. Carbon brushes
are of specify them cause damages to the
motor of the tool.
Safety Warnings for Polishers
Safety warnings common for sanding with sand-
ing discs working with polishing.
a. This power tool is intended to function as a
sander and polisher. Read all safety warn-
ings, instructions, illustrations and speci-
fications provided with this power tool.
Failure the follow all instructions listed below
may result in electric shock, fire and/or serious
injury.
b. Operations such as grinding or cutting-
off are not recommended to be performed
with this power tool. Operations for which
the power tool was not designed may create a
F 000 622 334 | 01.2011
tools. Check for
hazard and cause personal injury.
c. Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because the
accessory can be attached to your power tool,
it does not assure safe operation.
d. The rated speed of the accessory must be at
least equal to the maximum speed marked
on the power tool. Accessories running faster
than their rated speed can break and fly apart.
e. The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or
controlled.
f. The arbor size of wheels, flanges, backing
pads or any other accessory must properly
fit the spindle of the power tool. Accessories
with arbor holes that do not match the
mounting hardware of the power tool will run
out of balance, vibrate excessively and may
cause loss of control.
g. Do not use a damaged accessory. Before
each use, inspect the accessory such as
abrasive wheels for chips and cracks,
backing pads for cracks, tears or excess
wear, wire brushes for loose or cracked
wires. If power tool or accessory is
dropped, inspect for damage or install an
undamaged accessory. After inspecting and
installing an accessory, position yourself
and bystanders away from the plane of the
rotating accessory and run the power tool
at maximum no-load speed for one minute.
Damaged accessories will normally break
apart during this test time.
h. Wear personal
Depending on
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and shop apron capable
of stopping small abrasive or workpiece
fragments. The eye protection must be
capable of stopping flying debris generated by
various operations. The dust mask or respirator
must be capable of filtrating particles generated
by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
i. Keep bystanders a safe distance away
from the work area. Anyone entering the
work area must wear personal protective
equipment. Fragments of workpiece or of
a broken accessory may fly away and cause
injury beyond immediate area of operation.
protective equipment.
application, use face
Bosch Power Tools