Terminal Function Of Ics; Ic2300 (Rfkwmpt480Ga): Ic Microprocessor - Panasonic SA-PT480PH Service Manual

19 Terminal Function of ICs

19.1. IC2300 (RFKWMPT480GA): IC
MICROPROCESSOR
Pin TERMINAL NAME
No.
1 EDA
2 ECK
3 ASS_MUTE
4 ECO_CTRL
5 RMT
6 ECHO_LVL1
7 ECHO_LVL2
8 BYTE
9 CNVSS
10 XCIN(32K)
11 XCOUT(32K)
12 RESET
13 XOUT
14 VSS
15 XIN
16 VCC
17 CEC
18 ECHO_MUTE
19 SYNC
20 FX_INT
21 FLD_STB
22 TUN_SDIO
23 LED_CTRL
24 TUN_SDCLK
25 DC_DET1
26 DC_DET2
27 FLD_OUT
28 FLD_CLK
29 DAP/DSP_I2CCLK
30 DAP/DSP_I2CDAT
31 DBG_TX
32 DBG_RX
33 SCLK
34 DAP_MUTE
35 UART_TX
36 UART_RX
37 TUN_RST
38 iPhone_DAT
39 iPhone_CLK
40 iPhone_RST
41 EPM
42 TUN_GPIO
43 FX_DET
44 FX_DI
45 FX_SCS
46 CE
47 FX_DO
48 FX_CLK
49 iPod_VIDEO_SEL
I/O Description
O EEPROM IC Data Signal
O EEPROM IC Clock Signal
O Bypass Auto Speaker Circuit
O Control Voltage Supply of D-
AMP (For Echo Mode)
I Remote Control Signal
I/O Echo Control level 1
I/O Echo Control level 2
I External data bus width select
input
I Micon Programming-Processor
/ Single Chip Mode
I Clock In (32KHz)
O Clock Out (32KHz)
I Microp Reset Signal
I Clock In
- GND
O Clock Out
- VCC +3.3V
I CEC IN/OUT PORT
O Bypass Echo Circuit
I AC Sync Signal
I Interrupt from Wireless module
O FL Display Strobe Signal
O Tuner I2C Data
O Power On LED control
O Tuner I2C Clock
I Power Supply Failure Detection
(F76)
I D-Amp and Fan Failure Detec-
tion (F61)
O FL Display Data Out Signal
O FL Display Clock Signal
I/O I2C Clock to DSP / DAP
I/O I2C Data to DSP / DAP
O UART TX for Debug
I UART RX for Debug
I Clock Signal (For Flash Writing)
O DAP Master mute
I/O iPod UART Transmitter Data
I iPod UART Receiver Data
I/O Tuner Reset Signal
I I2C Data to iPod IC (Software
I2C control)
I I2C Clock to iPod IC (Software
I2C control)
O Reset Signal to iPhone
L For Downloading Purpose (with
pull down)
I Tuner General Purpose IO
H Wireless Detection
- Not in use
- Not in use
I For Downloading Purpose (with
pull up)
- Not in use
- Not in use
O Selection of Composite Output
from iPod or Back End
50 PCONT
51 RGB_H
52 VMUTE2
53 VMUTE
54 YC_H
55 SCART_MUTE
56 UNLOAD_SW
57 INNER_SW
58 TRAY_CCW_L
59 TRAY_CW_H
60 DVD_MUTE
61 SEL_A
62 VCC
63 FX_BUNDLE_CS
64 VSS
65 HP_MUTE
66 NRST
67 VCOMP_MUTE
68 WIDE1
69 DSP_RESET
70 DSP_MUTE
71 DAP_RST
72 iPod_CTRL_SW
73 WL_OFF_SW
74 iPod_DET
75 VOL0_CTRL
76 ADC_RESET
77 DVD_CMD
78 DVD_STAT
79 DVD_CLK
80 iPod_OC
81 DAC_MUTE1
82 BATT_PCONT
83 iPod_ACC
84 DAC_RESET
85 DAC_MUTE
86 MIC_SW
87 MD3
88 MD2
89 APD
90 SEL_B
91 KEY2
92 KEY1
93 ASS_INPUT
94 DAC_RESET1
95 DES2
96 AVSS
97 DES1
98 VREF
99 AVCC
100 ECS
143
O System Power Control
- Not in use
- Not in use
I/O Video Mute Control
- Not in use
- No Connection
I DLS6E Unload Switch Signal
I DLS6E Inner Switch
O DLS6E Tray Close Signal
O DLS6E Tray Open Signal
I Mute Signal from DVD Module
(Reverse logic of ZFLAG)
O Analog Input Selector Control A
- +3.3V System Supply
I Chip Select for Wireless Bun-
dled model for Smart Setup
- System Ground
- No Connection
- DAC Reset signal (from DV)
- No Cennection
- No Connection
O DSP Reset Signal
O DSP Mute Signal
O DAP Reset
O iPod Control Switch
O Not in use
I iPod Insertion Detection
O Volume Control
O ADC Reset Signal
O DVD Command
I DVD Status
I DVD Clock
I iPod Overcurrent Protection
- Not in Use
I/O iPod Charging Power Control
I iPod Authorisation IC
- Not in use
- Not in use
I MIC Plug in Detection
I DVD Panel Code Digit 3
I DVD Panel Code Digit 2
I Detect Auto Power Down Level
O Analog Input Selector Control B
I Keyline 2: 1st key is OPEN/
CLOSE
During STOP mode, act as KI1
After wake up, act as AN5
I Keyline 1: 1st key is POWER
During STOP mode, act as KI0
After wake up, act as AN4
- Not in use
- Not in Use
I Model Selector
- Analog GND
I Series Selector
- Voltage Reference +3.3V
- Analog +3.3V Supply
O EEPROM IC Chip Select