Page 1
A3G Green Rotary Laser INSTRUCTION MANUAL...
Page 2
SAFETY Please read this instruction manual before operating this product. Please store this instruction manual in the carry case for future reference. CAUTION: Class 3 Laser Product Do not stare directly into the laser beam from apertures. Do not disassemble the instrument or attempt to perform any internal servicing as this will void your warranty.
Please ensure the following items are included with your laser. If anything is missing please contact your retailer. 90° INCHES SLEEP 45° 10° 180° Remote control Detector and clamp 2x Laser targets Laser glasses Carry case General A3G Charger Rechargeable battery pack...
USING YOUR LASER Power Supply ‣ The General A3G is supplied with a rechargeable Ni-MH battery pack that is located in the base of the unit. ‣ It is recommended that the battery pack be completely charged before use. ‣ Charging time is approximately 5 hours.
Page 9
Horizontal Set Up ‣ Select a place as close as practical to the work site. Ensure the location is clear of traffic. ‣ Attach the laser to a tripod and place on a level surface. Ensure the unit is secured correctly and tightened in position. Vertical Set Up ‣...
Page 10
Operation ‣ To turn the unit on press the power button. Self levelling will commence and the laser will begin to rotate. ‣ If the unit is outside the self levelling range the unit will not level causing the laser beam to flash continuously. Speed Control ‣...
Page 11
Tilt Alarm ‣ Once the unit has been levelled off the tilt alarm can be enabled by pressing the tilt alarm button. The tilt alarm indicator light will flash for approximately 15 seconds. Once the light is constant the alarm is enabled. ‣...
Page 12
Using your detector ‣ Switch the detector on by pressing the power button. The speaker will beep once indicating the unit is operating. ‣ The LCD screen will display the battery level, detection mode and speaker function. ‣ To change between coarse and fine mode press the coarse / fine mode button ‣...
Page 13
Using your remote ‣ Ensure the unit is turned on and the laser is rotating. ‣ Press the speed control button to increase or decrease the speed of the lasers rotation. ‣ To focus the laser beam between two points press the scanning mode button.
CHECKING CALIBRATION Before doing any precision levelling it is advised to check the calibration of the unit. ‣ Set up the laser on a tripod at about 30m facing a wall or staff with a detector. ‣ Allow the unit to level. ‣...
TROUBLE SHOOTING Laser does not turn on ‣ Check the batteries. They may be in the wrong way or need replacing. ‣ Check the battery compartment for signs of damage. Ensure they are clean and not bent. ‣ Connect the main power adaptor. Laser turns on but does not rotate ‣...
Page 16
Detector does not detect the laser beam ‣ Check the batteries. They may be in the wrong way or need replacing. ‣ Check that the laser is operating correctly. Detector speaker is not functioning ‣ Check sound is on. ‣ Check the laser is operating correctly and producing a beam.
‣ The supplied charger is specific to this product. Do not purchase or use any other type of charger or power adaptor. ‣ Although the A3G has an IP65 rating always ensure to clean the instrument with a dry, soft cloth after use in dusty, damp or wet conditions before storing.
WARRANTY The General A3G comes with a 3 year manufacturers warranty. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
SPECIFICATIONS Specifications General A3G Product code 70012 Warranty 3 Years Accuracy ±2mm at 30m Range 300m Levelling range ±9% / ±5° Laser class 3 Green Battery life 20 hours Battery type 4x C (sealed pack) IP rating Weight (kg) 1.85...