Sony HCD-RV7 Service Manual page 58

HCD-RV7/RV8
QQ
3 7 63 1515 0
Pin No. Pin Name
111 CLOK
112 L SENS
113 SENS
114 L SLCK
115 SCLK
116 VDD3
117 ATSK
118 XUGF
119 XPCK
120 L GFS
121 GFS
122 VSS3
123 L CDC2PO
124 C2PO
125 L SCOR
126 SCOR
127 COUT
128 VDD4
129 MIRR
130 DFCT
131 L FOK
TE
L 13942296513
132 FOK
133 MDP
134 VSS4
135 SSTP
136 FSTO
137 SFDR
138 SRDR
139 VDD5
140 TFDR
141 TRDR
142 FFDR
143 FRDR
144 VSS5
145 WFCK
146 WDCK
147 ASYE
148 VDD6
149 XTAI
150 XTAO
151 VSS6
www
152 TES1
153 TEST
154, 155 RESERVE .
156 AVD0
157 IGEN
58
http://www.xiaoyu163.com
I/O
I
Serial data transfer clock signal input
I
SENS signal input
O
SENS signal output
O
SENS serial data readout clock signal output
I
SENS serial data readout clock signal input
—
Digital power supply terminal (+2.5V) (for CD-DSP block)
I/O
Input/output terminal for anti-shock Not used
O
XUGF signal output terminal Not used
O
XPCK signal output terminal Not used
I
Guard frame sync signal input
O Guard frame sync signal output
—
Digital ground terminal
I C2 pointer signal input
O
C2 pointer signal output
I Subcode sync (S0+S1) detection signal input
O
Subcode sync (S0+S1) detection signal output
O Numbers of track counted signal output terminal Not used
—
Digital ground terminal (for CD-DSP block)
I/O Mirror signal input/output terminal Not used
I/O
Defect signal input/output terminal Not used
I/O
Focus OK signal input/output
I/O
Focus OK signal input/output
O
Spindle motor servo drive signal output
—
Digital ground terminal
I
Detection signal input from limit in switch The optical pick-up is inner position when "H"
O
2/3 frequency-division output of the XTAI (pin <zv. )
O
Sled motor servo drive signal (+) output
O
Sled motor servo drive signal (–) output
—
Digital power supply terminal (+2.5V) (for CD-DSP block)
O
Tracking coil servo drive signal (+) output
O
Tracking coil servo drive signal (–) output
O Focus coil servo drive signal (+) output
O
Focus coil servo drive signal (–) output
— Digital ground terminal
O
Write frame clock signal output terminal Not used
O Word clock signal output terminal Not used
I
Asymmetry circuit on/off control signal input terminal "L": off, "H": on Not used
— Digital power supply terminal (+2.5V) (for CD-DSP block)
I
Main system clock input terminal (33.8688 MHz)
O Main system clock output terminal (33.8688 MHz)
—
Digital ground terminal
I
Input terminal for the test Normally: fixed at "L"
x ao
y
I
Input terminal for the test Normally: fixed at "L"
— i
Not used
—
Analog power supply terminal (+2.5V)
I
Operational amplifier constant current input
http://www.xiaoyu163.com
8
Description
Q Q
3 6 7 1 3
Not used
u163
.
2 9 9 4 2 8
1 5 0 5 8 2 9 9 4
m
co
9 9
2 8 9 9