Additional Information; Troubleshooting - Sony DVP-NC60K Service Manual

DVP-NC60K/NC62K
QQ
3 7 63 1515 0
◆ DOWNMIX (DVD VIDEO/DVD-RW only)
Switches the method for mixing down to 2
channels when you play a DVD which has
rear sound elements (channels) or is recorded
in Dolby Digital format. For details on the
rear signal components, see "Checking the
audio signal format" (page 45). This function
affects the output of the following jacks:
– LINE OUT L/R (AUDIO) jacks
– DIGITAL OUT (OPTICAL or COAXIAL)
jack when "DOLBY DIGITAL" is set to
"D-PCM" (page 71).
DOLBY
Normally, select this position.
SUR- Multi-channel audio signals are
ROUND output to 2 channels for enjoying
surround sounds.
NORMAL Multi-channel audio signals are
downmixed to 2 channels for use
with your stereo.
◆ DIGITAL OUT
Selects if audio signals are output via the
DIGITAL OUT (OPTICAL or COAXIAL)
jack.
ON Normally select this position.
When you select "ON," see
"Setting the digital output signal"
for further settings.
OFF The influence of the digital circuit
upon the analog circuit is
minimal.
TE
L 13942296513

Additional Information

Troubleshooting

If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
Power
The power is not turned on.
, Check that the mains lead is connected
securely.
Picture
There is no picture/picture noise appears.
, Re-connect the connecting cord securely.
, The connecting cords are damaged.
, Check the connection to your TV (page 15)
and switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
, The disc is dirty or flawed.
, If the picture output from your player goes
through your VCR to get to your TV or if
you are connected to a combination TV/
VIDEO player, the copy-protection signal
applied to some DVD programmes could
affect picture quality. If you still experience
problems even when you connect your
player directly to your TV, try connecting
your player to your TV's S VIDEO input
(page 15).
, The disc is recorded in a colour system that
is different from your TV.
, You have selected "PROGRESSIVE
AUTO" or "PROGRESSIVE VIDEO"
www using the PROGRESSIVE button on the
front panel (the PROGRESSIVE indicator
lights up) even though your TV cannot
accept the progressive signal. In this case,
select "NORMAL (INTERLACE)" so that
the PROGRESSIVE indicator turns off.
, If the colour system of your player does not
match with that of your TV, change the
colour system of the player. For details, see
page 16. (You cannot change the colour
system of the DVD disc itself.)
http://www.xiaoyu163.com
Setting the digital output signal
Switches the method of outputting audio
signals when you connect a component such
as an amplifier (receiver) or MD deck with a
digital input jack.
For connection details, see page 18.
Select "DOLBY DIGITAL," "MPEG,"
"DTS," and "48kHz/96kHz PCM" after
setting "DIGITAL OUT" to "ON."
If you connect a component that is
incompatible with the selected audio signal, a
loud noise (or no sound) may be heard from
the speakers, risking damage to your ears or
speakers.
◆ DOLBY DIGITAL (DVD VIDEO/DVD-RW
only)
Selects the type of Dolby Digital signal.
D-PCM Select this when the player is
connected to an audio
component without a built-in
Dolby Digital decoder. You can
select whether the signals
conform to Dolby Surround
(Pro Logic) or not by making
adjustments to the
"DOWNMIX" item in
"AUDIO SETUP" (page 71).
DOLBY Select this when the player is
DIGITAL connected to an audio
component with a built-in
Dolby Digital decoder.
◆ MPEG (DVD VIDEO/DVD-RW only)
Selects the type of MPEG audio signal.
PCM Select this when the player is
connected to an audio
component without a built-in
MPEG decoder. If you play
multi-channel MPEG audio
sound tracks, only the Front (L)
and Front (R) signals will be
output from your two front
speakers.
MPEG Select this when the player is
connected to an audio
component with a built-in
MPEG decoder.
,
, Even if your TV is compatible with
progressive format 525p/625p signals, the
image may be affected when you set the
player to progressive format. In this case,
select "NORMAL (INTERLACE)" using
the PROGRESSIVE button on the front
panel so that the PROGRESSIVE indicator
turns off and the player is set to normal
(interlace) format.
The picture does not fill the screen, even
though the aspect ratio is set in "TV TYPE"
under "SCREEN SETUP."
, The aspect ratio of the disc is fixed on your
DVD.
Sound
There is no sound.
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, The player is connected to the wrong input
jack on the amplifier (receiver) (page 18).
, The amplifier (receiver) input is not
correctly set.
, The player is in pause mode or in Slow-
motion Play mode.
, The player is in fast forward or fast reverse
mode.
, If the audio signal does not come through
the DIGITAL OUT (OPTICAL or
COAXIAL) jack, check the audio settings
(page 71).
, While playing a Super VCD on which the
audio track 2 is not recorded, no sound will
come out when you select "2:STEREO,"
"2:1/L," or "2:2/R."
, When playing multichannel MPEG audio
soundtracks, only the Front (L) and Front
(R) signals will be output from two front
speakers.
Sound distortion occurs.
, Set "AUDIO ATT" in "AUDIO SETUP" to
"ON" (page 70).
The sound volume is low.
x ao
y
, The sound volume is low on some DVDs.
The sound volume may improve if you set
"AUDIO DRC" in "AUDIO SETUP" to
. i
"TV MODE" (page 70).
, Set "AUDIO ATT" in "AUDIO SETUP" to
"OFF" (page 70).
,
http://www.xiaoyu163.com
8
◆ DTS
Selects whether or not to output DTS signals.
OFF Select this when the player is
connected to an audio
component without a built-in
DTS decoder.
ON Select this when the player is
connected to an audio
component with a built-in DTS
decoder.
◆ 48kHz/96kHz PCM (DVD VIDEO only)
Selects the sampling frequency of the audio
signal.
48kHz/16bit The audio signals of DVD
VIDEOs are always converted
to 48kHz/16bit.
96kHz/24bit All types of signals including
96kHz/24bit are output in their
original format. However, if the
signal is encrypted for
copyright protection purposes,
the signal is only output as
48kHz/16bit.
Note
The analogue audio signals from the LINE OUT L/
R (AUDIO) jacks are not affected by this setting
and keep their original sampling frequency level.
Q Q
3 6 7 1 3
71 72
Operation
The remote does not function.
, The batteries in the remote are weak.
, There are obstacles between the remote and
the player.
, The distance between the remote and the
player is too far.
, The remote is not pointed at the remote
sensor on the player.
The disc does not play.
, The disc is turned over.
Insert the disc with the playback side facing
down.
, The disc is skewed.
, The player cannot play certain discs
(page 6).
, The region code on the DVD does not match
the player.
, Moisture has condensed inside the player
(page 3).
, The player cannot play a recorded disc that
is not correctly finalized (page 7).
The MP3 audio track cannot be played
(page 54).
, The DATA CD is not recorded in an MP3
format that conforms to ISO 9660 Level 1/
Level 2 or Joliet.
, The DATA DVD is not recorded in MP3
format that conforms to UDF (Universal
Disk Format).
, The MP3 audio track does not have the
extension ".MP3."
, The data is not formatted in MP3 even
though it has the extension ".MP3."
, The data is not MPEG-1 Audio Layer III
data.
, The player cannot play audio tracks in
mp3PRO format.
, "MODE (MP3, JPEG)" is set to "IMAGE
(JPEG)" (page 57).
, The DATA CD/DATA DVD contains a
DivX video file.
u163
.
73 74
1-18
2 9 9 4 2 8
1 5 0 5 8 2 9 9 4
The JPEG image file cannot be played
(page 54).
, The DATA CD is not recorded in a JPEG
format that conforms to ISO 9660 Level 1/
Level 2, or Joliet.
, The DATA DVD is not recorded in JPEG
format that conforms to UDF (Universal
Disk Format).
, The file has an extension other than
".JPEG" or ".JPG."
, The image is larger than 3072 (width)
2048 (height) in normal mode, or more than
3,300,000 pixels in progressive JPEG.
(Some progressive JPEG files cannot be
displayed even if the file size is within this
specified capacity.)
, The image does not fit the screen (the image
is reduced).
, "MODE (MP3, JPEG)" is set to "AUDIO
(MP3)" (page 57).
, The DATA CD/DATA DVD contains a
DivX video file.
The MP3 audio tracks and JPEG image
files start playing simultaneously.
, "MODE (MP3, JPEG)" is set to "AUTO"
(page 57).
The DivX video file cannot be played.
, The file is not created in DivX format.
, The file has an extension other than ".AVI"
or ".DIVX."
, The DATA CD (DivX video)/DATA DVD
(DivX video) is not created in a DivX
format that conforms to ISO 9660 Level 1/
Level 2 or Joliet/UDF.
, The DivX video file is larger than 720
(width) × 576 (height).
The album/track/file names are not
displayed correctly.
, The player can only display numbers and
alphabet. Other characters are displayed as
m
" * ".
The disc does not start playing from the
co beginning.
, Programme Play, Shuffle Play, Repeat Play,
or A-B Repeat Play is selected (page 28).
, Resume play has taken effect (page 25).
9 9
2 8 9 9
×