LD ON mode in the test mode oscillates with the laser forcibly. 2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗ : See page 50. DV-393-S...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DV-393-S...
For WVXTL type INSTRUCTION BOOK (E) INSTRUCTION BOOK (E/I) INSTRUCTION BOOK (G/F) INSTRUCTION BOOK (S/H) INSTRUCTION BOOK (R) 7-10,17 "Operating Instructions" For WYXZT5, WYXZT/UR5 types POLY BAG INSTA5 TRANSMITTER CORD,RCA PIN BATTERY,MANGAN PACKAGE PACKAGE GIFT SHEET PACKAGE PACKAGE PACKAGE,PAD DV-393-S...
Page 7
Instruction Book See Contrast table (2) Instruction Book See Contrast table (2) Instruction Book See Contrast table (2) (2) CONTRAST TABLE DV-393-S/WVXT5, /WYXZT/UR5, DV-393-K/WYXZT5, /WYXZT/UR5 and DV-393-S/WYXZT5 are constructed the same except for the following : DV-393-S/ DV-393-S/ DV-393-S/ DV-393-K/ DV-393-K/ Mark No.
Page 9
See Contrast table (2) 101N Spring,Flap-DVD 743WKA0052 Screw,Tap Tite(B)Pan (3x6) 810913060U Screw,Tap Tite(P) (2.6x8) 811022680U (2) CONTRAST TABLE DV-393-S/WVXT5, /WYXZT/UR5, DV-393-K/WYXZT5, /WYXZT/UR5 and DV-393-S/WYXZT5 are constructed the same except for the following : DV-393-S/ DV-393-S/ DV-393-S/ DV-393-K/ DV-393-K/ Mark No.
CD2301 NOTE: Applying positions AA, AB and AC for the CLASS PART NO. MARK PART NAME grease are displayed for this section. GREASE GEM1018 G-555G Check if the correct grease is applied for each GYA1001 G-313Y position. GEM1036 FL-78A DV-393-S...
: VIDEO JACK BLOCK M2602 BCZ3B05 SLD+ SLD+ SLED MOTOR SLD- SLD- : POWER PORT BLOCK LIMIT SW LIMIT SW SW(GND) SW(GND) ESE22MH22 LOADING MOTOR PCB ASSY (A2F101A610) CD2302 CP2302 CLOSE SW-2(CLOSE) GND(D) SSS-28-5 GND(SW) OPEN SW-1(OPEN) M2603 BCZ3B05 LOADING MOTOR DV-393-S...
Page 17
: S VIDEO SIGNAL ROUTE (C ch) (R/CR) : VIDEO SIGNAL ROUTE (R/CR ch) (G/Y) : VIDEO SIGNAL ROUTE (G/Y ch) (B/CB) : VIDEO SIGNAL ROUTE (B/CB ch) : AUDIO DATA SIGNAL ROUTE (DA) : AUDIO SIGNAL ROUTE (Digital) CP601 DV-393-S...
3.5 DVD MT PCB ASSY(2/6) DVD MT PCB ASSY (A2I802A130) MEMORY BLOCK DV-393-S...
Page 19
S29AL016D70TFI020 NOTE :THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE : THE DC VOLTAGE EACH PART WAS OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-393-S...
ATTENTION : LES PIECES REPAREES PAR UN ETANT CAUTION : SINCE THESE PARTS MARKED BY DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY. DANS LA NOMENCLATURE DES PIECES. DV-393-S...
Page 21
: RF SIGNAL ROUTE (RF) NOTE : THE DC VOLTAGE EACH PART WAS NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. DURING PLAYBACK. DV-393-S...
AUDIO JACK BLOCK (DA) (DA) (DA) (DA) NOTE : THE DC VOLTAGE EACH PART WAS NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-393-S...
Page 23
(DA) : AUDIO SIGNAL ROUTE (Digital) : AUDIO SIGNAL ROUTE (L ch) CAUTION : DIGITAL TRANSISTOR CAUTION : DIGITAL TRANSISTOR DV-393-S...
: AUDIO SIGNAL ROUTE (L ch) NOTE : THE DC VOLTAGE EACH PART WAS NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-393-S...
Page 25
(SC) (SY) (GY) (B/CB) (R/CR) (R/CR) CAUTION: DIGITAL TRANSISTOR CAUTION: DIGITAL TRANSISTOR DV-393-S...
FL DC+ -28V ATTENTION :LES PIECES REPAREES PAR UN ETANT CAUTION :SINCE THESE PARTS MARKED BY DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY. DANS LA NOMENCLATURE DES PIECES. DV-393-S...
Page 27
D_GND FROM/TO MEMORY D_GND PCB130 DMF072 NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE :THE DC VOLTAGE EACH PART WAS OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-393-S...
OPERATION 2 PCB ASSY SW660 : STOP SW662 : +SKIP SW663 : PLAY SW664 : - SKIP SW665 : PAUSE OPERATION 3 PCB ASSY SW667 : POWER OPERATION 3 PCB ASSY (A2I802ADF0) OPERATION 2 PCB ASSY (A2I802A280) B C G DV-393-S...
Page 29
CP4002 NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. DURING PLAYBACK. DV-393-S...
: LES PIECES REPAREES PAR UN ETANT ATTENTION : POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE DES FUSIBLE DE MEME TYPE N’UTILISER QUE CELLS DECRITES 1.6A 125V{F501} DANS LA NOMENCLATURE DES PIECES DV-393-S...
Page 31
PCB240 DPF010 CAUTION: DIGITAL TRANSISTOR NOTE : THE DC VOLTAGE EACH PART WAS NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. DV-393-S...
FROM/TO POWER AT+3.3V P.CON+12V P-H/I-L_RGB-H ASP/FS AMP_A_OUT_R AMP_A_OUT_L G/Y_VIDEO B/U_VIDEO R/V_VIDEO CVBS/C_VIDEO A_GND Q8101 Q8102 21PIN CTL IN 12.1 21PIN CTL DRV R8105 KTC3875S_Y_RTK 11.4 KTA1504S_Y_RTK 390 1/4W 11.4 12.1 R8101 4.7K 1/4W CAUTION: DIGITAL TRANSISTOR CAUTION: DIGITAL TRANSISTOR DV-393-S...
Page 33
Q8104 +-1% KRC104SRTK PCB240 DPE010 NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE : THE DC VOLTAGE EACH PART WAS OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-393-S...
Resistor array 3-terminal regulator LOADING MOTOR LOADING MOTOR PCB ASSY PCB ASSY (INSERTED PARTS) (CHIP MOUNTED PARTS) SIDE A SIDE B CD2302 CP2302 M2603 M2603 SW PCB ASSY LOADING MOTOR CD2301 M2602 SLED MOTOR CD2301 M2601 SPINDLE MOTOR CP2303 DV-393-S...
• Soldering time: Within 3 seconds • Soldering combination: Sn-3.0Ag-0.5Cu • When Soldering/Removing of solder, use the draw in equipment over the Pick Up Unit to prevent the Flux smoke from it. Short circuit using a soldering iron. Pick Up PCB Fig. 1 DV-393-S...
• After going into test mode, if you play back the disc, "DISC-NON" is displayed. • The video signal and the audio signal are outputted during the test mode. • The SKIP key and the SCAN key are effective during the test mode. TEST MODE: OFF POWER GGF1381 Test mode remote control unit DV-393-S...
3 LD ON DVD : Press the [TEST] (A8-5E) and [1] (A8-01) keys in order, and turn on the laser diode (650n). : Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780n). DV-393-S...
• Place the unit on a workstation equipped to protect against static electricity, such as conductive mat. • Soldering iron with ground wire or ceramic type is used. • A worker needs to use a ground conductive wrist strap for body. DV-393-S...
: [NTSC] PAL system : [PAL] Automatic setting : [AUTO] Scart terminal output [SK – ∗ ∗] (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] DV-393-S...
• Region confirmation mode (ESC + A.MON [Test mode remote control unit] + "1"-"8" [Test mode remote control unit] keys) After you press the A.MON key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. DV-393-S...
Character in bold : Item name : Information display 1 Destination indication Display it according to model information set from the FL Driver IC. 2 Region No. 3 ROM number 4 REG CHK 5 SUM CHK 6 CHIP VERSION DV-393-S...
%%e -2 : NG 7.0e -4 : NG 3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors) Note: ∗ Error of AV1 is not supported in this player. Indication plan contents Character in bold : Item name : Information display DV-393-S...
Measure the voltage between the two ends of R2320 or R2322 on the DVDM Assy. If the voltage is 0.4 V or higher, the 780-nm LD is degraded. To OPTICAL PICKU DVD MT PCB ASSY CP2301 Front side SIDE A DV-393-S...
DVD MT PCB Assy Check the video signal path between DVD IC (DVD MT Assy IC4002) displayed on the monitor Video circuit after DVD IC and video-out terminal (see the block diagram) (The FL display lights. The (IC4001) mechanism does not work.) DV-393-S...
Page 59
Is there a problem with the format of the disc ? (block noise, freeze, other) No sound Is signal output from IC4001-pin184 and pin 186 on the DVD MT Assy (Picture is normal) DVD MT PCB Assy DVD IC (IC4001) DV-393-S...
Page 60
Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be (DVD MT Assy : IC4001) generated, because the DVD processing is performed by a single chip. 64M SDRAM No power. (DVD MT Assy : IC4005) Block noise is generated during playback. DV-393-S...
Up PCB and DVD PCB connector. 1-4: DVD PCB (Refer to Fig. 1-4) Power PCB Remove the 3 screws 1. Remove the 4 screws 2. Remove the DVD PCB in the direction of arrow. DVD PCB Fig. 1-2 Fig. 1-4 DV-393-S...
Page 63
3 supports 1. between A and B. Fig. 2-3-D Remove the Plate Clamper, Magnet Clamper and Clamper. Check Hook Check Hook Plate Clamper Magnet Clamper Main Frame Loading Motor PCB Ass’y Clamper Check Hook Fig. 2-5-A Fig. 2-3-E DV-393-S...
Page 64
Remove the Switch PCB Ass'y. 8.0 ± 0.2mm Remove the screw 4. Remove the Gear Feed. Feed Motor Remove the 2 screws 5. Remove the Feed Motor. Remove the Gear Motor. Safety surface for pressing of the insert. Fig. 2-7-C DV-393-S...
Page 65
When installing the FFC, fold it correctly and install it as shown from Fig. 2-8. NOTE Do not make the folding lines except the specified positions for the FFC. [ 24 pin FFC ] Printing _Serface 85±1 mm Reinforcement Plat To Pick Up PCB Fig. 2-8 DV-393-S...
Page 67
TV Encoder Module Videop RF Amplifier Video DAC Servo IO Servo Motor Processor Video Drive Processor interlacer Spindle Control FLASH MPEG-1/2 Audio JPEG Memory Video Decoder Controller DRAM System Audio Parser Audio Output CPPM/CPRM SPDIF System GPIO 32-bit RISC IR/VFD DV-393-S...
Page 68
MT1389FE/E-L (DVD MT PCB ASSY : IC4001) • MPEG/MICON/DSP CPU • Pin Function DV-393-S...
Page 77
Note: 1. The Main column is the main function, Alt. means alternative function. 2. The external TV encoder mode only supports CCIR-656 mode. DV-393-S...
• Static electricity or other external influences may cause malfunctioning of this unit. In this case, unplug the power cord and then plug back in. This will usually reset the unit for proper operation. If this does not correct the problem, please consult your nearest Pioneer service center.
Page 79
Digital Theater Systems, Inc. MP3 (MPEG1 audio layer 3) is a compressed stereo audio file format. Files are recognized by their file extension “.mp3”. MPEG audio An audio format used on Video CD/ Super VCDs and some DVD discs. DV-393-S...
Returns to the previously dis-played menu screen. • Press to jump to the previous/next 7 HOME MENU chapter or track. 8 Display Compatible Description of the display. This mark indicates compatibility with DVD-RW discs recorded on a DVD recorder in Video Recording mode. DV-393-S...
Press to pause playback; press again to restart. 12 PLAY MODE Press to display the Play Mode menu. (You can also get to the Play Mode menu by pressing HOME MENU and selecting Play Mode). Press to jump to the beginning of the current DV-393-S...
Page 82
Use to select menu options, etc. playing. 24 ZOOM 18 MENU Press to change the zoom level. Press to display a DVD disc menu, or the Disc Navigator if a VR format DVD-RW, CD, Video CD , MP3, WMA or JPEG disc is loaded. DV-393-S...
• Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Position to be cleaned Cleaning tools Cleaning tools Remark Remark Pickup leneses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DV-393-S...
Need help?
Do you have a question about the DV-393-S and is the answer not in the manual?
Questions and answers