Advertisement
30106077GB.fm Page 2 Monday, July 30, 2007 11:00 AM
CONSUMPTION DATA
Temperature
Load
Programme
(°C)
(kg)
Cotton (Anti-bacterial)
95
8.0
Cotton***
60
8.0
Cotton
40
8.0
Synthetics
60
3.5
Synthetics
40
3.5
Daily load
40
6.0
Quick wash (30 min)
30
6.0
Delicates
30
2.5
Handwash / Wool
40
2.0
Handwash / Wool
30
2.0
60
8.0
Steam Refresh
—
1.0
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The time indicated on the display can deviate from the values in the table, because it takes into account the operating conditions
applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
Add detergent as indicated on the front page and as
described in the chapter "Detergent and Additives" in
your Instructions for Use.
1. Push the "On/Off" button
. The blue light circle
signals that the washer is switched on.
2. Select the desired programme by pushing the
corresponding programme button; it is marked by a
blue light.
3. The temperature and spin speed indicated on the
display can be altered by pressing the "Temperature"
button or the "Variable spin" button.
SELECT ANY DESIRED OPTION
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
"Big Items" button
• Select this option for washing big laundry items such as
blankets made of synthetic fibres, bed covers filled
with feathers or artificial fibres, sleeping bags,
bathmats and similar.
"Steam stain removal" button
• Treats the laundry with hot steam during the wash
cycle in order to help removing stains.
• Selectable for laundry made of cotton and/or
synthetics within temperature range of 40 to 60°C.
"Steam sanitisation" button
• Eliminates bacteria and helps sanitizing the laundry.
• Appropriate for cotton and/or synthetic laundry items with
care label
within temperature range of 40 to 60°C.
• Prolongs the programme by approx. half an hour to an
hour, depending on the load size.
Black process 45.0° 100.0 LPI
Water
Energy
Approx. Programme Duration
(l)
(kWh)
(hours : minutes)*
82**
2.40
2:10
69
1.36
2:20
77
0.85
2:05
48**
0.95
1:35
44
0.55
1:20
79
0.70
1:00
72
0.35
0:30
60
0.45
0:50
45
0.65
0:40
45
0.35
0:36
75
0.95
4:00
0.5
0.20
0:10
"Prewash" button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
• Do not use liquid detergent for the main wash when
activating the Prewash option.
"Intensive rinse" button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very
soft water or for washing baby linen, and helps people
with allergies.
"Rinse hold" button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and
prevent colours from changing.
• This option is particularly recommended for the
programmes "Synthetics", "Daily load" and "Delicates".
• It is particularly useful if you want to postpone spinning
to a later time, or if you want to drain only.
• If you select "Rinse hold", do not leave the laundry to
soak for too long.
Note: The programme stops to "Rinse hold" at the time
the "Rinse hold" symbol on the display lights up. The blue
light under the "Start/Pause" button
flashes.
Terminate the "Rinse hold" option:
• Press the "Start/Pause" button
; the programme
will terminate automatically with the final spin cycle for
the present wash programme.
• If you do not wish to spin the clothes, push the
"Drain/Reset (3sec)" button and then the "Start/
Pause" button
to start the Drain programme.
"Variable spin" button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed "0" is selected, the final spinning is
cancelled but intermediate spin peaks remain during
rinse. The water is drained out only.
START DELAY
The "Start delay" allows to run the machine at the
consumer's convenience, for example at night when
electricity is cheaper. Do not use liquid detergent when
activating the "Start delay".
• Select programme, temperature, spin speed and options.
• Press the "Start delay" button to select the delay time
up to 23 hours.
• Press the "Start/Pause" button
.
The countdown of the delay time begins; the clock
symbol next to the delay time and the dot between
hours and minutes flash.
• The time delay indication disappears when the
programme starts and it is replaced by the remaining
programme time.
• Once having pressed the "Start/Pause" button
the number of hours preselected can be reduced by
pressing and holding the "Start delay" button. From 1
hour on, the delay time can also be reduced by minutes.
To cancel the "Start delay"
..before you press the "Start/Pause" button:
• Select another programme or press the "Drain/Reset
(3sec)" button.
..after having pressed the "Start/Pause" button:
• Press the "Drain/Reset (3sec)" button for at least 3
seconds - the start delay time disappears from the display.
PROGRAMME START
Open the tap and press the "Start/Pause" button
The blue light under the "Start/Pause" button
is on.
The programme sequence indicator shows the current
programme phase, running from left to right through
Wash, Rinse, Spin/Drain.
"DOOR OPEN" INDICATION
Before starting and after end of a programme, the symbol
lights to show that the door can be opened. As long as a
wash programme is running, the door remains locked and
must on no account be forced open. In case you have an
urgent need to open it during a running programme, refer
to "Cancel (Reset) a running programme before the end".
CHILD LOCK
You can lock the buttons of the control panel against
improper use (e.g. by children).
• Press the temperature and the spin speed button
simultaneously and hold them for at least 3 seconds.
The key symbol on the display lights up.
• To unlock the buttons again: proceed in the same way.
RED INDICATIONS ON THE DISPLAY
"Water tap closed"
The appliance has no or insufficient water supply. Open
the water tap; if the indication still lights up, refer to the
"Troubleshooting Guide" in the Instructions for Use.
"Clean pump"
Waste water is not pumped out. Check whether the drain
hose is kinked or the filter must be cleaned; in the latter case
refer to the Instructions for Use ("Removing the Filter").
"Service"
Lighting up of the "Service" indication can be caused by a
fault in an electrical component. Refer to the
"Troubleshooting Guide" in your Instructions for Use; if
the fault persists, contact our After Sales Service.
PROGRAMME END
,
•
The symbols of the programme sequence indicator
are dark, and the "Door open" symbol
1. Switch the machine off by pushing "On/Off"
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button
to pause the
programme. The light flashes.
2. Select the new programme, temperature, any options
and another spin speed if you want.
.
3. Press the "Start/Pause" button
again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
The "Drain/Reset (3sec)" button cancels a programme
before the end.
•
Press the "Drain/Reset (3sec)" button for at least 3
seconds. Any existing water is drained out before the
door can be opened. Caution! The washing might still
be hot.
Whirlpool is a registered trademark of Whirlpool USA
5019 301 06077
lights up.
.
Advertisement
