Download
Share
Print this page
HP MSM410 Quick Start Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Wireless Access Point
  5. MSM410
  6. Quick start manual

HP MSM410 Quick Start Manual

Hide thumbs Also See for MSM410:

Advertisement

Quick Links

See also: Reference Manual
The MSM410 is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED 802.11a/b/g/n
product. The Wi-Fi CERTIFIED Logo is a certification mark of the 
Wi-Fi Alliance.
This Quickstart shows you how to get started using the MSM410 Access Point (US J9426A/B, WW J9427A/B).
After reading this Quickstart, you can visit www.hp.com/go/procurve/manuals and download documents of particular interest such as the MSM3xx / MSM4xx
Access Points Management and Configuration Guide and the MSM7xx Controllers Management and Configuration Guide.

Hardware overview

Package contents
MSM410, documentation, mounting bracket, two mounting screws (4 mm x 25 mm (5/32 x
1 inch)) with wall anchors, and two T-bar clips with four nuts (only provided with rev B:
US J9426B and WW J9427B).
Ports
•
Ethernet port: Auto-sensing 10/100/1000 BaseT Ethernet port with RJ-45 connector.
The port supports Power over Ethernet (PoE) 802.3af.
MSM410 Access Point Quickstart
Status lights (left to right)
Power, Ethernet, Radio
Lock tab
In
Ethernet port (Port 1)
•
Console port: Standard console (serial) port with an RJ-45 connector. For details, see
Console Ports in the MSM3xx / MSM4xx Access Points Management and Configuration
Guide.
Never connect the Console port to an Ethernet switch or PoE power source.
Warning:
This may damage the MSM410. Connect it only to other serial ports via an
RJ-45 to DB-9 adapter.
Cable channel
Mounting bracket
tab slots
Console port

Advertisement

loading

Related Manuals for HP MSM410

Summary of Contents for HP MSM410

  • Page 1: Hardware Overview

    This Quickstart shows you how to get started using the MSM410 Access Point (US J9426A/B, WW J9427A/B). After reading this Quickstart, you can visit www.hp.com/go/procurve/manuals and download documents of particular interest such as the MSM3xx / MSM4xx Access Points Management and Configuration Guide and the MSM7xx Controllers Management and Configuration Guide.

  • Page 2: About Controlled Mode And Autonomous Mode

    Power light blinks every two seconds. The MSM410 is starting up. The Reset button is accessible via a hole on the bottom of the MSM410 as identified below. Power light blinks once per second. The MSM410 is looking for an IP address, or Insert a paper clip under the cable and into the reset button hole at the precise angle shown.

  • Page 3: Installation

    The MSM410 can be mounted on a wall, a wall-mounted electrical box, or a suspended the intended country. It is the responsibility of the end user to ensure that installation and ceiling.

  • Page 4: Installing In A Plenum

    If using a PoE injector, use Ethernet cables to connect your computer to the data in through the hole. port of the PoE injector and the MSM410 to the data and power out port of the PoE Position the MSM410 against the bracket so that the bracket tabs fit into the tab slots on injector.

  • Page 5: Test The Wireless Network

    To avoid a delay after switching modes, clear the ARP (address • Assign a static IP address to the MSM410. The address must be on the same subnet as Note: resolution protocol) cache on your computer. In Windows for example, the network to which the MSM410 will connect.

  • Page 6: Performing Additional Configuration

    HP ProCurve Networking G. Performing additional configuration Configure your computer LAN port and connect it to the same network as the MSM410. Re- launch the MSM410 management tool at https://<IP address> where <IP address> is the MSM410 IP address from Step E above.