table of contents Introduction 4 Using the Operators Manual Product Identification 5 Pressure Washer 5 Engine Safety 6 Understanding the Machine Safety Decal 7 Safety Rules 7 Hazard Symbols and Meanings Gas Washer Components 14 Component Chart Assembly 15 Unpack the Pressure Washer 15 Attach Handle Pre-Operation Checklist 16 Follow the Checklist Below 16 Connect Hose and Water Supply to Pump Starting Your Washer 17 How to Start your Pressure Washer Shutting Down Your Washer 21 ...
Page 3
table of contents Power Cord Connection 23 Connection Safety Starting Your Electric Washer 25 How to Start your Pressure Washer Shutting Down Your Electric Washer 28 How to Shut Down your Pressure Washer Spray Tips 29 How to Use Spray Tips 29 Change Spray Tips 29 Usage Tips Using Black Soap Nozzle 30 Apply Detergent Trouble Shooting 31 Gas Engine Trouble Shooting Chart 32 Electric Motor Trouble Shooting Chart 33 ...
introduction attention: read through the complete manual prior to the initial use of your pressure washer. Using the Operator’s manual The operating manual is an important part of your pressure washer and should be read thoroughly before initial use, and referred to often to make sure adequate safety and service concerns are being addressed. Reading the owner’s manual thoroughly will help avoid any personal injury or damage to your machine. The information in this manual will offer you the most effective tools for cleaning as well as the safest. By knowing how best to operate this machine you will be better positioned to show others who may also operate the unit. This manual contains information for the complete range of pressure washers, and is placed in order starting from the safety requirements to the operating functions of your machine. You can refer back to the manual at any time to help troubleshoot any specific operating functions, so store it with the machine at all times. Notice Actual pressure released at the point of discharge may very by machine due to varying factors including: Volume of water being fed to the ma- chine by the water source, the inclusion of a Chemical injector in the line, or variations in Engine performance...
product identification Record Identification Numbers Pressure Washer If you need to contact an Authorized Dealer or Customer Service line (1- 866-770-1711) for information on servicing, always provide the product model and identification numbers. You will need to locate the model and serial number for the machine and record the information in the places provided below. Date of Purchase: Dealer Name: Dealer Phone: Product Identification Numbers Model Number: Serial Number: Engine Horse Power:...
safety IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WarnInG – When using this product basic precautions should always be followed, including the following: 1. Read all the instructions before using the product. 2. To reduce the risk of injury, close supervision is necessary when a product is used near children. 3. Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the controls. 4. Stay alert – watch what you are doing. 5. Do not operate the product when fatigued or under the influence of alcohol or drugs. 6. Keep operating area clear of all persons 7. Do not overreach or stand on unstable support. Keep good footing and balance at all times. 8. Follow the maintenance instructions specified in the manual.
Page 7
safety Understanding the Machine Safety Labels The machine safety label shown below is placed on your machine to draw attention to potential safety hazards. WARNING! ATION WARNING! PRECAUTIONS! 85.609.158 Do not leave unit running longer than 1 minute without using or pump will overheat. Ne pas laisser 8”. fonctionner inutilement l’unité pendant plus d’une minute. Do not let unit freeze. La pompe risquerait de surchau er.
safety Save these Instructions Safety Rules this is the safety alert symbol. It is used to alert you to potential personal injury hazards. obey all safety messages that follow this symbol to avoid possible injury or death. The safety alert symbol ( ) is used with a signal word (DANGER, CAUTION, WARNING), a pictorial and/or a safety message to alert you to hazards. DANGER indicates a hazard which, if not avoided, will result in death ...
Page 9
safety WARNING Risk of electrocution. Contact with power source can cause electric shock or burn. • NEVER spray near power source. WARNING Fuel and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. When Adding or Draining Fuel • Turn pressure washer OFF and let it cool at least 2 minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank. • Fill or drain fuel tank outdoors. • DO NOT overfill tank. Allow space for fuel expansion. • If fuel spills, wait until it evaporates before starting engine. • Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources. • DO NOT light a cigarette or smoke. When Starting Equipment • Ensure spark plug, muffler, fuel cap, and air cleaner are in place. • DO NOT crank engine with spark plug removed. When Operating Equipment • DO NOT tip engine or equipment at angle which causes fuel to spill. • DO NOT spray flammable liquids. When Transporting or Repairing Equipment • Transport/repair with fuel tank EMPTY or with fuel shutoff valve OFF. • Disconnect spark plug wire. When Storing Fuel or Equipment with Fuel in Tank • Store away from furnaces, stoves, water heaters, clothes dryers, or other appliances that have pilot light or other ignition source because...
Page 10
safety WARNING Running engine gives off carbon monoxide, an odorless, colorless, poison gas. Breathing carbon monoxide can cause headache, fatigue, dizziness, vomiting, confusion, seizures, nausea, fainting or death. Some chemicals or detergents may be harmful if inhaled or ingested, causing severe nausea, fainting, or poisoning. • Operate pressure washer ONLY outdoors. • Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes, or other openings. • DO NOT start or run engine indoors or in an enclosed area, even if windows and doors are open. • Use a respirator or mask whenever there is a chance that vapors may be inhaled. • Read all instructions with mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors. WARNING Starter cord kickback (rapid retraction) can result in bodily injury. Kickback will pull hand and arm toward engine faster than you can let go. Broken bones, fractures, bruises, or sprains could result. • NEVER pull starter cord without first relieving spray gun pressure. • When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback. • After each starting attempt, where engine fails to run, always point spray gun in safe direction and squeeze spray gun trigger to release high pressure. • Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when spray gun kicks back.
Page 11
safety WARNING Use of pressure washer can create puddles and slippery surfaces. Kickback from spray gun can cause you to fall. • Operate pressure washer from a stable surface. • The cleaning area should have adequate slopes and drainage to reduce the possibility of a fall due to slippery surfaces. • Be extremely careful if you must use the pressure washer from a ladder, scaffolding, or any other similar location. • Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when spray gun kicks back. WARNING Contact with muffler area can result in serious burns. Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire. • DO NOT touch hot parts and AVOID hot exhaust gases. • Allow equipment to cool before touching. • Keep at least 5 feet (1.5 m) of clearance on all sides of pressure washer including overhead. WARNING Risk of eye injury. Spray can splash back or propel objects. • Always wear safety goggles when using this equipment or in vicinity of where equipment is in use. • Before starting the pressure washer, be sure you are wearing adequate safety goggles. • NEVER substitute safety glasses for safety goggles.
Page 12
safety WARNING The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation. Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury. • DO NOT allow CHILDREN to operate pressure washer. • NEVER repair high pressure hose. Replace it. • NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal. • NEVER connect high pressure hose to nozzle extension. • Keep high pressure hose connected to pump and spray gun while system is pressurized. • ALWAYS point spray gun in safe direction and squeeze spray gun trigger, to release high pressure, every time you stop engine. • NEVER aim spray gun at people, animals, or plants. • DO NOT secure spray gun in open position. • DO NOT leave spray gun unattended while machine is running. • NEVER use a spray gun which does not have a trigger lock or trigger guard in place and in working order. • Always be certain spray gun, nozzles and accessories are correctly attached. WARNING Starter and other rotating parts can entangle hands, hair, clothing, or accessories. • NEVER operate pressure washer without protective housing or covers. • DO NOT wear loose clothing, jewelry or anything that may be caught in the starter or other rotating parts. • Tie up long hair and remove jewelry.
Page 13
safety WARNING Unintentional sparking can result in fire or electric shock. When Adjusting or Making Repairs to Your Pressure Washer • Disconnect the spark plug wire from the spark plug and place the wire where it cannot contact spark plug. When Testing for Engine Spark • Use approved spark plug tester. • DO NOT check for spark with spark plug removed. NOTICE High pressure spray may damage fragile items including glass. • DO NOT point spray gun at glass when using red 0° spray tip. • NEVER aim spray gun at plants. NOTICE Improper treatment of pressure washer can damage it and shorten its life. • If you have questions about intended use, ask dealer or contact nearest authorized dealer. • NEVER operate units with broken or missing parts, or without protective housing or covers. • DO NOT by-pass any safety device on this machine. • DO NOT tamper with governed speed. • DO NOT operate pressure washer above rated pressure. • DO NOT modify pressure washer in any way. • Before starting pressure washer in cold weather, check all parts of the equipment to be sure ice has not formed there. • NEVER move machine by pulling on hoses. Use handle provided on unit.
gas washer components read this operator’s manual and safety rules before operating your pressure washer. 15. 4. 1. Spray Tips Detergent, 0°, 15°, and 40°: for various high pressure cleaning applications. 2. High Pressure Hose Connect one end to water pump and the other end to spray gun. 3. Pressure Control Knob Varies pressure of high pressure spray. 4. Water Inlet Connection for garden hose. 5. High Pressure Outlet Connection for high pressure hose. 6. Pump Develops high pressure. 7. Oil Level Indicator Level should be at halfway 8.
assembly Your pressure washer requires some assembly and is ready for use after it has been properly serviced with the recommended oil and fuel. If you have any problems with the assembly of your pressure washer, please call the pressure washer help line. If calling for assistance, please have the model and serial number from the data tag available. Unpack the Pressure Washer 1. Remove the parts bag, accessories, and inserts included with pressure washer. 2. Open box completely by cutting each corner from top to bottom. 3. Ensure you have all included items prior to assembly. Attach Handle 1. Place handle (A) onto handle supports (B) connected to main unit. Make sure holes (C) in handle align with holes on handle supports. NOTE: It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the handle supports. 2. Insert carriage bolts through holes from outside of unit and attach a plastic knob from inside of unit. Tighten by hand. 3. Insert multi-colored quick connect spray tips and other supplied accessories in spaces provided on handle.
pre-operation checklist Follow the Checklist Below Prior to Using the Machine Each Time 1. Check to ensure the engine oil is at the proper level. Use SAE 10W30 Oil 2. Check the 2 handle knobs to ensure they are tight and will not vibrate loose. 3. Add fuel to the gas tank. 4. Connect and tighten the garden hose to the GHA (garden hose inlet) connection. ** Water must be turned on prior to starting the washer, pull the spray trigger to ensure water is moving the through the lines and out the nozzle without any leaks before starting the unit.** 5. Review the safety guidelines in the manual prior to starting the unit.
starting your washer How to Start Your Pressure Washer To start your pressure washer for the first time, follow these instructions step-by-step. This starting information also applies if you have let the pressure washer sit idle for at least a day. 1. Place pressure washer near an outside water source capable of supplying water at a flow rate greater than 3.8 gallons per minute and no less than 20 PSI at pressure washer end of garden hose. DO NOT siphon supply water. 2. Make sure unit is in a level position. 3. Connect garden hose to water inlet on pressure washer pump. NOTICE DO NOT run the pump without the water supply connected and turned on. • Damage to equipment resulting from failure to follow this instruction will void warranty. 4. Attach wand extension to spray gun. Tighten by hand. 5. Choose desired spray tip, pull back nozzle extension collar, insert spray tip and release collar. Tug on spray tip to make sure it is securely in place. See Spray Tips.
Page 18
starting your washer 6. Uncoil high pressure hose and attach quick connect end of hose to base of spray gun. Pull down on collar of quick connect, slide onto spray gun and let go of collar. Tug on hose to be sure of tight connection. WARNING The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation. • NEVER connect high pressure hose to nozzle extension. • Keep high pressure hose connected to pump and spray gun while system is pressurized. • Always be certain spray gun, nozzles and accessories are correctly attached. 7. Similarly, attach other end of high pressure hose to high pressure outlet (A) on pump. Pull down on collar of quick connect, slide onto pump and let go of collar. Pull on hose to be sure of tight connection. axial pump triplex pump Pump Uses 30W Non-Detergent Mineral Oil 8. Turn Water Supply on, point gun in a safe direction and squeeze the trigger to purge the pump of air and debris. Do this for at least 30 seconds. 9. Take a look at all connections to make sure there are no leaks or loose connections. IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F/38°C).
Page 19
starting your washer 10. Connect the garden hose to the water inlet. Tighten by hand. 11. To start the machine, locate the engine switch on the side of the engine, and switch it to the ON position. (see component chart to locate switch) Check to ensure fuel valve is in the ON position and if starting cold apply the choke. 12. Pull recoil cord slowly until resistance is felt and then pull rapidly to avoid kickback. Make sure to position yourself in a balanced position. DO NOT place hand on engine muffler for balance, this will result in severe burn. WARNING Running engine gives off carbon monoxide, an odorless, colorless, poison gas. Breathing carbon monoxide can cause headache, fatigue, dizziness, vomiting, confusion, seizures, nausea, fainting or death. • Operate pressure washer ONLY outdoors. • Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes, or other openings. • DO NOT start or run engine indoors or in an enclosed area, even if windows and doors are open. IMPORTANT: Before starting the pressure washer, be sure you are wearing adequate safety goggles. WARNING Risk of eye injury. Spray can splash back or propel objects. • Always wear safety goggles when using this equipment or in vicinity of where equipment is in use. • Before starting the pressure washer, be sure you are wearing adequate safety goggles. • NEVER substitute safety glasses for safety goggles.
Page 20
starting your washer WARNING Starter cord kickback (rapid retraction) can result in bodily injury. Kickback will pull hand and arm toward engine faster than you can let go. Broken bones, fractures, bruises, or sprains could result. • NEVER pull starter cord without first relieving spray gun pressure. • When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback. • After each starting attempt, where engine fails to run, always point spray gun in safe direction and squeeze spray gun trigger to release high pressure. • Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when spray gun kicks back. WARNING The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation. Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury. • DO NOT allow CHILDREN to operate pressure washer. • NEVER repair high pressure hose. Replace it. • NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal. • NEVER connect high pressure hose to nozzle extension. • Keep high pressure hose connected to pump and spray gun while system is pressurized. • ALWAYS point spray gun in safe direction and squeeze spray gun trigger, to release high pressure, every time you stop engine. • NEVER aim spray gun at people, animals, or plants. • DO NOT secure spray gun in open position. • DO NOT leave spray gun unattended while machine is running. • NEVER use a spray gun which does not have a trigger lock or trigger guard in place and in working order.
shutting down your washer WARNING Contact with muffler area can result in serious burns. Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire. • DO NOT touch hot parts and AVOID hot exhaust gases. • Allow equipment to cool before touching. • Keep at least 5 feet (1.5 m) of clearance on all sides of pressure washer including overhead. How to Shut Down Your Pressure Washer 1. Release spray gun trigger and let engine idle down. 2. Turn the engine switch to the OFF position. 3. ALWAYS point spray gun in a safe direction, squeeze spray gun trigger to release retained high water pressure. IMPORTANT: Spray gun traps high water pressure, even when engine is stopped and water is disconnected. Couplings will not release if under pressure. WARNING The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation. Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury. • Keep high pressure hose connected to pump and spray gun while system is pressurized. • ALWAYS point spray gun in safe direction and squeeze spray gun trigger, to release high pressure, every time you stop engine.
Page 22
electric washer components read this operator’s manual and safety rules before operating your pressure washer. 1. ON/OFF Switch 2. Motor 3. Pump 4. GFCI 5. Power Cord 6. Detergent Hose 7. Adjustable Unloader Knob 8. Water Outlet 9. Water Inlet 10.
power cord connection Important Safety Instructions WARNING - When using this product basic precautions should always be followed, including the following: 1. Read all instructions before using product. 2. To reduce the risk of injury, close supervision is necessary when a product is used near children. 3. Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the controls. 4. Stay alert - watch what you are doing 5. Do not operate the product when fatigued or under the influence of alcohol or drugs. 6. Keep operating area clear of all person 7. Do overreach or stand on unstable support. Keep good footing and balance at all times 8. Follow the maintenance instructions specified in the manual. 9. For a grounded or double-insulated product rated 250 volts or less, single phase: “This Product Is Provided With A Ground Fault Circuit Interrupter Built Into The Power Cord Plug. If Replacement Of The Plug Or Cord Is Needed, Use Only Identical Replacement Parts.” WARNING Risk of Injection or Injury to persons Do not direct discharge stream at persons WARNING Risk of electrocution.
Page 24
power cord connection 1. Make certain the motor switch is in the “OFF” position. 2. Ensure electrical supply is identical to the specifications listed on the pressure washer data plate. 3. GROUNDING INSTRUCTIONS: This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. 4. DANGER: Improper connection of the equipment-grounding conductor can result in a risk of electrocution. Check with a qualified electrician or service personnel if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use any type of adaptor with this product. 5. GROUND FAULT CIRCUIT INTERRUPTER PROTECTION: This pressure washer may be provided with a Ground Fault Circuit Interrupter (GFCI) built into the plug or the power supply cord, test the GFCI each time it is plugged into an outlet according to instructions on the GFCI. DO NOT use the pressure washer if the test fails! The GFCI provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI protection. 6. WE DO NOT RECOMMEND THE USE OF EXTENSION CORDS. If use of an extension cord is unavoidable, it must be plugged into a GFCI found in circuit boxes or protected receptacles. Use only 3-wire extension cords that have 3-prong grounding-type plugs and 3-pole cord connectors that accept the plug from the product. Use only extension cords that are intended for outdoor use. These extension cords are identified by a marking “Acceptable for use with outdoor appliances; store indoors while not in use.” Use only extension cords having an electrical rating not less than the rating of the product. Do not use damaged extension cords. Examine extension cord before ...
Page 25
maintenance intructions CAUTION: Only certified electrician can service the motor. Contact the authorized dealer for service or additional information. User Maintenance Instructions: General Inspection: Inspect the motor at regular intervals, approxi- mately every 500 hours of operation or every 3 months, whichever occurs first. Keep the motor clean and the ventilation openings clear. Check that the motor is clean. Check that the interior and exterior of the motor is free of dirt, oil, grease, water, etc. Oily vapor, paper pulp, textile lint, etc. Can accumulate and block motor ventilation. If the motor is not properly venti- lated, overheating can occurs and cause early motor failure. Lubrication & Bearings: Bearing grease will lose its lubrication ability over time. The lubricating ability of grease (over time) depends primar- ily on the type of grease, the size of the bearing, the speed at which the bearing operates, and the severity of the operation conditions. Good re- sults can be obtained if the following recommendations are used in your maintenance program. Type of Grease: A high grade ball or roller bearing grease should be used. Recommended grease for standard service conditions is Polyrex EM (Mobil). Equivalent and compatible grease include: Texaco Polystar, Rykon Premium #2, Pennzoil Pen 2 Lube and Chevron SRI-2. - Maximum operating temperature for standard motors=110°C. - Shut-down temperature in case of a malfunction = 115°C. Lubrication Intervals: Recommended lubrication intervals are every 2200hours. For more information contact the authorized service center.
Page 26
starting your electric washer WARNING To reduce the risk of electrocution, keep all connec- tions dry and off the ground. Do not touch plug with wet hands How to Start Your Pressure Washer To start your pressure washer for the first time, follow these instructions step-by-step. This starting information also applies if you have let the pressure washer sit idle for at least a day. 1. Place pressure washer near an outside water source capable of supplying water at a flow rate greater than 3.8 gallons per minute and no less than 20 PSI at pressure washer end of garden hose. DO NOT siphon supply water. 2. Make sure unit is in a level position. 3. Connect garden hose to water inlet on pressure washer pump. NOTICE DO NOT run the pump without the water supply connected and turned on. • Damage to equipment resulting from failure to follow this instruction will void warranty. 4. Attach wand extension to spray gun. Tighten by hand. 5. Choose desired spray tip, pull back nozzle extension collar, insert spray tip and release collar. Tug on spray tip to make sure it is securely in place. See Spray Tips. 6. Uncoil high pressure hose and attach quick connect end of hose to base of spray gun. Pull down on collar of quick connect, slide onto spray gun and let go of collar. Tug on hose to be sure of tight connection.
Page 27
starting your electric washer WARNING The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation. • NEVER connect high pressure hose to nozzle extension. • Keep high pressure hose connected to pump and spray gun while system is pressurized. • Always be certain spray gun, nozzles and accessories are correctly attached. 7. Similarly, attach other end of high pressure hose to high pressure outlet (A) on pump. Pull down on collar of quick connect, slide onto pump and let go of collar. Pull on hose to be sure of tight connection. axial pump triplex pump 8. Turn Water Supply on, point gun in a safe direction and squeeze the trigger to purge the pump of air and debris. Do this for at least 30 seconds. 9. Take a look at all connections to make sure there are no leaks or loose connections. IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F/38°C). 10. Connect the garden hose to the water inlet. Tighten by hand. 11. To start the machine, locate the ON/OFF switch on the side of the motor, and switch it to the ON position. (see component chart to locate switch) ...
Page 28
starting your electric washer IMPORTANT: Before starting the pressure washer, be sure you are wearing adequate safety goggles. WARNING The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation. Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury. • DO NOT allow CHILDREN to operate pressure washer. • NEVER repair high pressure hose. Replace it. • NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal. • NEVER connect high pressure hose to nozzle extension. • Keep high pressure hose connected to pump and spray gun while system is pressurized. • ALWAYS point spray gun in safe direction and squeeze spray gun trigger, to release high pressure, every time you stop engine. • NEVER aim spray gun at people, animals, or plants. • DO NOT secure spray gun in open position. • DO NOT leave spray gun unattended while machine is running. • NEVER use a spray gun which does not have a trigger lock or trigger guard in place and in working order. • ALWAYS be certain spray gun, nozzles and accessories are correctly attached. WARNING Risk of eye injury. Spray can splash back or propel objects. • Always wear safety goggles when using this equipment or in vicinity of where equipment is in use. • Before starting the pressure washer, be sure you are wearing adequate safety goggles. • NEVER substitute safety glasses for safety goggles.
Page 29
shutting down your electric washer How to Shut Down Your Pressure Washer 1. Release spray gun trigger. 2. Turn the motor switch to the OFF position. 3. ALWAYS point spray gun in a safe direction, squeeze spray gun trigger to release retained high water pressure. IMPORTANT: Spray gun traps high water pressure, even when motor is stopped and water is disconnected. Couplings will not release if under pressure. WARNING The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation. Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury. • Keep high pressure hose connected to pump and spray gun while system is pressurized. • ALWAYS point spray gun in safe direction and squeeze spray gun trigger, to release high pressure, every time you stop engine.
spray tips soaper YELLOW WHITE BLACK How to Use Spray Tips The quick–connect on the nozzle extension allows you to switch between four different quick connect spray tips. Spray tips can be changed while pressure washer is running once spray gun trigger safety lock is engaged. The spray tips vary the spray pattern as shown above. WARNING The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation. • NEVER exchange spray tips without the trigger safety lock engaged on the spray gun. • DO NOT twist spray tips while spraying. Follow these instructions to change spray tips: 1. Pull back collar on quick–connect and pull current spray tip off. Store spray tips in holder provided on the handle. Storing nozzles in the designated holder will help prevent debris clogging the tip. 2. Select desired spray tip: • For gentle rinse, select white 40° spray tip. • To scour surface, select yellow 15° or red 0° spray tip. • To apply detergent, select black spray tip. 3. Pull back on collar, insert new spray tip and release collar. Tug on spray tip to make sure it is securely in place. Usage Tips • For most effective cleaning, keep spray tip from 8 to 24 inches away ...
using black soap nozzle To apply detergent, follow these steps: 1. Review use of spray tips. 2. Prepare detergent solution as required by job. 3. Place small filter end of detergent siphoning tube into detergent container. NOTE: Make sure the filter is fully submerged in detergent while applying detergent. THIS WASHER WILL ONLY DRAW SOAP WITH THE BLACK SOAPER NOZZLE. WHITE, RED, AND YELLOW NOZZLE WILL NOT DRAW SOAP. 4. Make sure black spray tip is installed. 5. Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump. Turn on water. NOTICE You must attach all hoses before you start the engine.
troubleshooting Troubleshooting Chart If you are experiencing a problem that is not listed in this chart, or have checked all the possible cause listed and you are still experiencing the problem, see your authorized dealer. GASOLINE ENGINES Problem Cause Correction Unit has following 1. Low pressure spray tip installed. 1. Replace with high pressure spray tip. problems: failure to 2. Water inlet is blocked. 2. Clear inlet. produce pressure, erratic 3.
Page 33
troubleshooting Engine will not start; or 1. Low oil level 1. Fill crankcase to proper level starts and runs rough 2. Dirty air cleaner 2. Clean or replace air cleaner 3. Out of gasoline 3. Fill fuel tank 4. Stale gasoline 4.
storage Thermal Relief Valve is 1. Water temperature is too high 1. Use cool water only. open and discharging 2. Pump has operated more than 3 mins 2. Pull trigger at least 30 seconds every 3 mins water from side of pump without pulling trigger Leak in the fittings 1.
storage When fuel stabilizers are used according to their instructions, there is no need to drain the gasoline from the engine prior to storage. Run the engine for a short time to circulate stabilizer throughout the fuel system. Engine and fuel can then be stored up to 24 months. If gasoline is drained, the use of a fuel stabilizer in the storage container is still recommended to maintain freshness. Storing the Engine See the engine operator’s manual for instructions on how to properly prepare the engine for storage. NOTICE You must protect your unit from freezing temperatures. • Failure to do so will permanently damage your pump and render your unit inoperable. • Freeze damage is not covered under warranty. NOTE: Pump Saver is available as an optional accessory. It is not includ- ed with the pressure washer. Contact the nearest authorized dealer to purchase Pump Saver. To use Pump Saver, make sure the pressure washer is turned off and disconnected from supply water. Read and follow all instructions and warnings given on the Pump Saver container. Other Storage Tips 1. DO NOT store fuel from one season to another unless it has been treated as described in Protect Fuel System. 2. Replace fuel container if it starts to rust. Rust and/or dirt in fuel can cause problems if it’s used with this unit. 3. Cover unit with a suitable protective cover that does not retain moisture. WARNING Storage covers can be flammable. • DO NOT place a storage cover over a hot pressure washer. • Let equipment cool for a sufficient time before placing the cover on the equipment. 4. Store unit in a clean and dry area.
Page 36
If you need assistance with the assembly or operation of this Pressure Washer please call 1-866-770-1711...