Page 1
This is an unvented portable heater. It uses air (oxygen) from the area in which it is used. Adequate combustion and ventilation air must be provided. Refer to page 3. UL733, CSA B140.8, CSA B140.9.3 01/15 70204 2015 JM HEATSTAR by ENERCO, 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 866-447-2194...
THE HEATER. • PLUG ELECTRICAL CORD INTO A PROPERLY GROUN- DED THREE-PRONG RECEPTACLE. HS50K & HS75KT WARNING: Not suitable for use on wood floors or other combustible materials. When used the heater should rest on a suitable insulating material at least 1 inch thick and extending 3 feet or more beyond the heater in all directions.
Never use in areas normally for habitation and /or where • headache children may be present. • dizziness 10. Operate only on a stable, level surface. (HS50K & HS75KT – • burning eyes and nose See wood floor warning). • nausea 11.
IMPROPER PRESSURE ADJUSTMENT HEATER START UP Problem: Heater does not have a strong consistent flame. HS50K: Plug the heater into a grounded 1 15V, 60 Hz, 1 Ø Heater smokes and spits raw fuel. outlet. Nose cone does not get cherry red.
Page 5
looseness caused by vibration or rough handling. Damaged When the heater is working normally: parts should be repaired or replaced before using heater The flame is contained within the heater. again. Check heater operation to be sure it is operating The flame is essentially yellow.
DIAGNOSTIC SAFETY SHUTDOWN AND TROUBLE SHOOTING These instructions are applicable for HS50K, HS75KT, HS125KT, HS175KT, HS210KT SYMPTOM TROUBLE SHOOTING High limit switch Open Circuit Make sure heater is cooled off, toggle switch to “OFF” position, wait 5 minutes and retry.
WIRING DIAGRAM 18AWG GRN HI-LIMIT ON/OFF SWITCH SWITCH 18AWG BLK 18AWG YELL 18AWG WHT 18AWG YELL CORD SET THERMOSTAT 18AWG BLUE 75KT,125KT,175KT,210KT ONLY 18AWG PURPLE FLAME CONTROL SCHEMATIC 18AWG PURPLE (connections may not be in same position on circuit board) 17AWG BLK ELECTR0DE 18AWG ORG...
DIRECT FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED SERVICE AGENCY. PARTS ORDERING INFORMATION: PURCHASING: Accessories may be purchased at any HEATSTAR by ENERCO local dealer or direct from the factory FOR INFORMATION REGARDING SERVICE Please call Toll-Free 866-447-2194 www.heatstarbyenerco.com...
Page 9
Cet appareil de chauffage portatif n'est pas ventilé. Il utilise l'oxygène de l'air ambiant. Une circulation d'air adéquate doit être assurée pour la combustion et la ventilation. Voir page 3. UL733, CSA B140.8, CSA B140.9.3 01/15 70204 2015 JM HEATSTAR by ENERCO, 4560 W. 160TH ST., CLEVELAND, OHIO 44135 USA • 866-447-2194...
Page 10
• BRANCHEZ LE CORDON ÉLECTRIQUE DANS UNE PRISE À TROIS BROCHES ADÉQUATEMENT MISE À LA TERRE. AVERTISSEMENT RELATIF AUX MODÈLES HS50K ET HS75KT : Non conçu pour être utilisé sur des planchers de bois ou d'autres matériaux combustibles. Lors de son fonctionnement, l'appareil de chauffage doit reposer sur un matériau isolant adéquat d'au moins 2,5 cm (1 po)
Page 11
De même, les systèmes de sécurité ne doivent pas être contournés 10. Utilisez uniquement sur des surfaces stables et de niveau. ni modifiés pour faire fonctionner l'appareil. (HS50K et HS75KT – Voir l'avertissement au sujet des Lorsque l'appareil de chauffage doit fonctionner en présence planchers de bois.) d'autres personnes, l'utilisateur est responsable d'informer ces 11.
Page 12
Retirez l'appareil de chauffage de la boîte. DÉMARRAGE DE L'APPAREIL Enlevez tout le matériel de protection installé sur l'appareil HS50K : Branchez le câble d'alimentation dans une prise pour le transport. mise à la terre de 1 15 V, 60 Hz, 1 Ø.
Page 13
etre enlevee pour l’installation d’un indiccateur de pressions. causée par l'aube d'entrée obstruera éventuellement les conduits Ce n’est pas une deuxieme vis d’ajustage. du gicleur et entraînera une diminution du débit d'air et de combustible. La pression augmentera graduellement, ce qui À...
Page 14
DIAGNOSTIC ET DÉPANNAGE APRÈS UN ARRÊT D'URGENCE Ces instructions s'appliquent aux modèles HS50K, HS75KT, HS125KT, HS175KT, HS210KT SYMPTÔME DÉPANNAGE Circuit ouvert du contacteur de commande maximale Assurez-vous que l'appareil est refroidi, placez l'interrupteur à « OFF », attendez 5 minutes et redémarrez l'appareil.
Page 15
SCHÉMA DE CÂBLAGE INTERRUPTEUR VRT AWG 18 INTERRUPTEUR MARCHE-ARRÊT COMMANDE MAX. NOIR AWG 18 JAUNE AWG 18 BLC AWG 18 JAUNE AWG 18 CORDON D’ALIMENTATION THERMOSTAT BLEU AWG 18 VIOLET AWG 18 SCHÉMA DE LA COMMANDE DE FLAMME VIOLET AWG 18 (la position des connexions peut différer sur le circuit imprimé) NOIR AWG 17...
Page 16
***PAGE LEFT INTENTIONALLY BLANK*** Kerosene Forced Air Heater Operating Instructions and Owner’s Manual...
Page 18
Debe suministrarse el aire necesario para la ventilación y la combustión. Consulte la página 3. UL733, CSA B140.8, CSA B140.9.3 03/14 Rev14E 70204 HEATSTAR by ENERCO, 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 866-447-2194...
Page 19
• ENCHUFE EL CABLE ELÉCTRICO EN UN TOMACORRIENTE DE TRES PATAS CORRECTAMENTE CONECTADO A TIERRA. HS50K Y HS75KT ADVERTENCIA: No adecuado para el uso en pisos de madera u otros materiales combustibles. Cuando usa el calentador debe colocarlo sobre un material...
Page 20
10. Úselo únicamente sobre una superficie nivelada y estable. Asegúrese de seguir las recomendaciones sobre las condiciones (Modelos HS50K y HS75KT: consulte la advertencia sobre de ventilación que se incluyen en esta sección de precauciones de pisos de madera).
Page 21
Deslice el espaciador en el eje próximo a la rueda. d. Deslice el eje parcialmente ensamblado a través del marco HS50K: desenchufe el calentador de la fuente de alimentación. de soporte de la rueda. HS75KT, HS125KT, HS175KT y HS210KT: lleve el interruptor e.
Page 22
CRONOGRAMA DIARIO El fabricante recomienda llenar el tanque con combustible por completo en caso de que el calentador vaya a estar almacenado GENERAL. Realice una inspección visual general del calentador por un período prolongado, a fin de minimizar la condensación para detectar partes sueltas o dañadas.
Page 23
APAGADO DE SEGURIDAD DE DIAGNÓSTICO Y RESOLUCIÓN DE PROBLEMAS Estas instrucciones se aplican a los modelos HS50K, HS75KT, HS125KT, HS175KT, HS210KT. SÍNTOMA DESCRIPCIÓN RESOLUCIÓN Circuito abierto, interruptor limitador máximo Asegúrese de que el calentador se enfríe por completo, lleve el interruptor a la posición “OFF”...
Page 24
DIAGRAMA DE CABLEADO 18 AWG VERDE LLAVE DE ENCENDIDO INTERRUPTOR LIMITADOR MÁXIMO 18 AWG NEGRO 18 AWG AMARILLO 18 AWG BLANCO 18 AWG AMARILLO JUEGO DE CABLES 18 AWG AZUL TERMOSTATO 75KT, 125KT, 175KT, 210KT ÚNICAMENTE 18 AWG PÚRPURA DIAGRAMA DE CONTROL DE LA LLAMA 18 AWG PÚRPURA (las conexiones pueden no estar...
Page 25
***PAGE LEFT INTENTIONALLY BLANK*** Kerosene Forced Air Heater Operating Instructions and Owner’s Manual...
Need help?
Do you have a question about the HS50K and is the answer not in the manual?
Questions and answers