Advertisement
Important Information
FRA40203
MODEL NO.
FAN FORCED WALL HEATER
APPAREIL DE CHAUFFAGE MURAL À AIR PLUSÉ
VOLTS AC
60HZ
WATTS
208
MUST BE USED WITH AWH-BB BACK BOX
DO NOT OPERATE WITHOUT FRONT COVER IN PLACE.
DOIT ÉTRE UTILISÉ AVEC BOÎTIER ARRIÈRE AWH-BB
NE PAS UTILISER SI LE COUVERCLE AVANT N'EST PAS EN PLACE.
MARLEY ENGINEERED PRODUCTS
BENNETTSVILLE, SC 29512
Maintenance
TO RESET MANUAL RESET LIMIT
Your heater is equipped with a manual reset safety thermal limit
control that will automatically turn the heater off to prevent a fire if the
heater overheats. This control is located on the fan panel assembly
between the element and fan blade and marked "reset". The red reset
button can be seen through the front grille when the heater is
installed. To reset, allow the heater to cool, then push the red button
that is visible through the hole in the fan panel. The heater should
immediately return to normal operation.
CAUTION
OPERATION OF THE MANUAL RESET SAFETY THERMAL LIMIT
CONTROL IS AN INDICATION THAT THE HEATER HAS BEEN
SUBJECTED TO SOME ABNORMAL CONDITION. IT IS RECOM-
MENDED THAT THE HEATER BE CHECKED BY A REPUTABLE
ELECTRICIAN OR REPAIR SERVICE TO ENSURE THE HEATER
HAS NOT BEEN DAMAGED.
Once each year the heater should be cleaned to remove dust and
other foreign material which has collected during the heating season.
This is a simple operation when performed as follows:
1. Turn off the electric power at main line switch (or remove all
fuses) to disconnect electric power from the heater.
THIS IS IMPORTANT.
2. Remove thermostat knob.
3. Remove front cover by depressing plastic snap tabs with a flat
bladed screw driver as shown in Figure 5. Release both tabs on
one side then rotate the front cover off of the fan deck.
4. With a vacuum cleaner nozzle or dust cloth, remove dust and
other foreign material.
Fig. 5
5. After cleaning, turn disconnect switch to ON position and reinstall
the grille.
6. Turn on the main line switch (or replace fuses) to restore power
to the heater. The heater is now ready for another season of
operation.
Part No. 5200-2302-002
0695
DATE CODE:
PHASE
HI LO
4800
3
774G LISTED
ROOM HEATER
!
DO NOT USE WATER OR DAMP CLOTH FOR CLEANING AND
DO NOT DISTURB THE HEATING ELEMENT.
LIMITED WARRANTY
All products manufactured by Marley Engineered Products are
warranted against defects in workmanship and materials for one year
from date of installation, except heating elements which are warranted
against defects in workmanship and materials for five years from date
of installation. This warranty does not apply to damage from accident,
misuse, or alteration; nor where the connected voltage is more than 5%
above the nameplate voltage; nor to equipment improperly installed or
wired or maintained in violation of the product's installation instructions.
All claims for warranty work must be accompanied by proof of the date
of installation.
The customer shall be responsible for all costs incurred in the removal
or reinstallation of products, including labor costs, and shipping costs
incurred to return products to Marley Engineered Products Service
Center. Within the limitations of this warranty, inoperative units should
be returned to the nearest Marley authorized service center or the
Marley Engineered Products Center, and we will repair or replace, at
our option, at no charge to you with return freight paid by Marley. It is
agreed that such repair or replacement is the exclusive remedy avail-
able from Marley Engineered Products.
THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER
WARRANTIES EXPRESSED OR IMPLIED. AND ALL IMPLIED WAR-
RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-
LAR PURPOSE WHICH EXCEED THE AFORESAID EXPRESSED
WARRANTIES ARE HEREBY DISCLAIMED AND EXCLUDED FROM
THIS AGREEMENT. MARLEY ENGINEERED PRODUCTS SHALL
NOT BE LIABLE FOR CONSEQUENTIAL DAMAGES ARISING WITH
RESPECT TO THE PRODUCT, WHETHER BASED UPON NEGLI-
GENCE, TORT, STRICT LIABILITY, OR CONTRACT.
Some states do allow the exclusion or limitation of incidental or
consequential damages, so the above exclusion or limitation may not
apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
For the address of your nearest authorized service center, contact
Marley Engineered Products in Bennettsville, SC, at 1-800-642-4328.
Merchandise returned to the factory must be accompanied by a return
authorization and service identification tag, both available from Marley
Engineered Products. When requesting return authorization, include all
catalog numbers shown on the products.
HOW TO ORDER REPAIR PARTS
In order to obtain any needed repair or replacement
parts, warranty service or technical information, please
contact Marley Engineered Products Service Center toll-
free by calling 1-800-642-HEAT.
When ordering repair parts, always give the informa-
tion listed as follows:
1. The Part Number
2. The Model Number
3. The Part Description
4. Date of Manufacture
ECR 35194
03-02
CAUTION
!
SPX Corporation
470 Beauty Spot Rd. East
Bennettsville, SC 29512 USA
Advertisement
