Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Lifan lf200 III
Summary of Contents for Lifan lf200 III
- Page 2 PREFACE The manual describes the basic operation and maintenance for the motorcycle,which should be read carefully before driving. Correctly use, service and maintenance can keep on a safe driving so as to minimize troubles of the motorcycle and keep it at an optimal performance, which can extend the period of usage .
-
Page 3: Table Of Contents
CONTENTS SAFE DRIVING OF THE MOTORCYCLE ..........2 WASHING AND ASSEMBLING SAFE DRIVING RULES ................2 OF FUEL SWITCH FILERING NET ............10 PROTECTIVE DEVICE ................2 INSPECTING OF LEAKAGE OF GAS PASSAGE ........10 CHANGING APPEARANCE OF THE VEHICLE ........2 OPERATION AND INSPECTION AND LOADING OF THE GOODS ................. -
Page 4: Safe Driving Of The Motorcycle
PROTECTIVE DEVICE WARNING: To prevent casualty and device damages, driving the motorcycle while mus t take to guarantee your security driving, you should put on a helmet, dus t hoo d an d face shield and gloves etc.protective tools. note of the traffic security. Can not drive until the motorcycle check carefully the silencer of the motorcycle is the part of the higher temperature , to avoid con- SAFE DRIVING RULES... -
Page 5: Parts
ACCESSORIES : our producing accessories went through special designing and passed testing on the motorcycle. being it is impossible for us to test all other factories products ,and so if no selecting our components ,resettling and using that you will allow for yourself .please you comply with safe driving regulations and o bey t he f ollowings everalp oints: carefully check components, no hindering sight, lessening clearance ground and side leaning angle,limiting suspension and steering structure shifting ,limiting and controlling operation no resettling the cooling device of the generator... -
Page 6: Vin Of The Motorcycle
tions Fig.3 off: when th e k ey is off circuit is of f , Fig.8 engine can t s tart ,the k ey c an t ake o ut (1)left handlebar on: when t he k ey i s on , circuit is o n , Ignition switch (2)left handlebar switch engine can start , the key can not take out... -
Page 7: Switch Of The Fuel Tank And The Cover Of The Fuel Tank And The Fuel
position: headlight , rear l ight ,meteri ndicating Spare : during d riving ,if t he f uel l evel i s l ower i n t he f uel t ank , main f uel Cover of the fuel tank passage can t s upply f uel,r otate th e h andleb ar o f t he f uel s witch t o t his p lace ,u se light are on. -
Page 8: Tyres
injecting . table 1 OPTION OF THE LUBRICATION (FIG 15) s/driving front wheel:175kpa rear wheel:200kpa It is the main factor that the lubrication influences on 20W/40 d/driving front wheel:225kpa rear wheel:225kpa the performance of the engine and life ,at the same 25W/40 tyre specs front wheel:80/100-18-47p... -
Page 9: Starting Of The Engine
8.check the tension of the drive chain ,the lubricated status . if serious abrasion CHARGE SO THAT DAMAGED.IF ELECTRIC STARTING CAN NOT START , &damage , need change in time . PLEASE USE FOOT STARTING. BREAK-IN OF THE ENGINE 9.check the operation system of steering check the sensitivity and stability of the operation During driving 0-1000km ,which it is essential phase that motorcycle rotating .avoid... -
Page 10: Brake And Stopping Of The Motorcycle
BRAKE AND STOPPING OF THE MOTORCYCLE damp so slip ,when the vehicles pass by ,should slow down ahead of time and take When need stop ,should close the throttle ,grasp at the handle of the clutch letting go note of keeping the vertical body ,otherwise may be cause the side sliding of the tyre the clutch ,meanwhile evenly use the front and rear brake till completely stop driving. -
Page 11: Clearance Of Accumulated Carbon
check whether leaks oil. BUY THE SPARK PLUG OF THIS TYPE,SHOULD CONTACT WITH THE DEAL- REMARKS ERS OR THE MAINTENANCE STATION ,SELECT THE PROPER REPLACE- DURING THE REPLACEMENT OF THE LUBRICATION ,MUST MOVE TO THE MENT .WHEN TAKE OUT THE SPARK PLUG ,SHOULD PAY A TTENTION TO AVOID PECULIAR OBJECTS PASSING THE HOLE OF THE SPARK PLUG EN- BLANK GEAR.NO ADDING TO ANY THE CHEMICAL ADDITION IN THE TERING INTO THE CYLINDER ,WHICH SPEED UP THE ABRASION OF THE... -
Page 12: Washing And Assembling Of Fuel Switch Filering Net
THE GAUZE CORE DAMAGED. normal position ,rotate the handlebar of the throttle and check whether exists in WHEN WASHING THE GAUZE CORE , NO USING THE CLEANSER OF THE fiction and the sense of the resistance . PETROL OR LOW POINT OF BURNING . ADJUSTING OF THE IDLE SPEED OF THE CARBURET OR(FIG21) Fig. -
Page 13: Inspecting And Adjusting And Lubricating Of The Driving Chain
Not only does the adjusting of the drive chain directly grasp at the handlebar of the front brake braking the front wheel ,press the front have an effect on the life of the drive chain ,but affects shock absorber ,up and down observe the restoring several times whether is normal. the effectivity of the driving and security of the driving , NOTES: IF FIND THE FRONT SHOCK ABSORBER DAMAGED,PLEASE AT and so must strictly and regularly check and maintain ac-... -
Page 14: Inspecting And Adjusting Of Rear Brake
(THE FRONT BRAKE ADJUSTING) The switch of the rear brake lies in the right side of the frame body ,which produces the brake momentum while turn on the the free stroke of the handlebar of the front brake is 10-20mm,if the free stroke is circuit of the brake light ,otherwise ,should adjust the adjust- incorrect,should adjust as follows: able nut of the switch of the rear brake light .if the movement... -
Page 15: Protection Of Battery
course of the reaction ,through the reaction of the oxidation and deoxiditing ,the ELECTROLYTE ,JUNK BATTERY WHICH DEALT WITH AS THE cleaning efficiency of the catalyst will change with the temperature ,density and REGULATIONS.NO LITTERING. speed of the flowing air . WARNING: during maintaining ,pay attention to the follow items: Electrolyte contains sulfur ,which avoids contacting skins &clothes ,if splashing the... -
Page 16: Instruction Of The Bumper (Option Loading Products )
(1)screw driver handlebar 1.before washing ,first check the spark plug and all of the mouth of the injecting oil (2)stud (3)spark plug wrench restalling whether is correct 2.flush the spot and oil print with the hose (4)five inch slip join t pliers 3.after washing ,scrub all surfaces with the towel of trim&... -
Page 17: Using After Keeping
7.under the atmosphere of damp and salt ,should cover a ply of thin protecting tar on MAINTENANCE SCHEDULE the surface of the outer metal 8.take apart the battery ,electrify and keep the drying place and the normal temperature, ODOMETER READING or PERIOD (Note 2) later electrify every month one time. -
Page 18: Electric Diagram
ELECTRIC DIAGRAM... -
Page 19: Specifications
SPECIFICATIONS Length width height 2080mm 680 mm 1130mm max power 12.5kw/8500r/min Wheelbase 1330mm max torque 15N.m/7000r/min Clearance ground 160mm volume of the cylinder 196.9ml Dry weight 140kg starting method electric/foot Steeringbar turning angle driving method chain drive Max loading 150kg changing speed ratio Max speed 100km/h...
Need help?
Do you have a question about the lf200 III and is the answer not in the manual?
Questions and answers