Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bdcom 1705b
Summary of Contents for Bdcom 1705b
- Page 1 1705 Router Web Configuration Manual...
-
Page 2: Table Of Contents
Content Content Chapter 1 The use of CMS..............................1 1.1 The network setting ............................... 1 1.2 Configuration guide ............................... 4 1.2.1 Startup and logging in ..........................4 1.3 First page ................................5 1.3.1 Typical setting............................6 1.3.2 Wizard setting............................6 1.3.3 Advanced setting............................ -
Page 3: Chapter 1 The Use Of Cms
1705Router Web Configuration Manual Chapter 1 The use of CMS Before configuring the router, please ensure that your computer is installed necessary softwares(for example: Windows 95/98/ME/NT2000/XP), and configure the netwok in reason. If you don’t know how to configure network, please read the setting explanation of next section ”Configure network”. - Page 4 1705Router Web Configuration Manual Click”property”keystoke and set IP address of the computer. In the dialog box of “Internet protocol(TCP/IP) property”, pitch on”use the following IP address”. Infilling 192.168.2.xxx in”IP address”(the range of xxx is 2~254). Infilling 255.255.255.0 in”subnet mask”. Infilling 192.168.2.1 in”default gateway”(that is the default IP address of 1705 router).
- Page 5 1705Router Web Configuration Manual Click”confirmation” and complete configuration. Step 3: Test the connection capability for computer and router. Beginning－>running－>key in”cmd”－>confirmation In command prompt use “ping” command to test the connection capability, perform”ping 192.168.2.1”: If shows: That shows the connection is successful. If shows: - 3 -...
-
Page 6: Configuration Guide
1705Router Web Configuration Manual That shows the connection is unsuccessful. You can check the following points: The indicator light which is joined computer port is bright or not. If the light isn’t bright, that shows the connection is abnormality on physical. You can change a line. -
Page 7: First Page
1705Router Web Configuration Manual 1.3 First page Click “next” to begin configuring. First the system will check router to ensure that whether it has been configured already or not. If there is configuration in router, system will show a list to show the configuration. Click “exit”... -
Page 8: Typical Setting
1705Router Web Configuration Manual 1.3.1 Typical setting You should config two parts of content in typical setting: WAN Port Setting: that is configuring interface for connecting Internet. There are three connection methods to choose: Typical setting 1: Using static IP on WAN port IP address: fill in the IP address obtained from ISP. - Page 9 1705Router Web Configuration Manual It is similar with WAN port setting of chapter 1.3.1, but it can configure one or two ports. You can refer to chapter 1.3.1 to configure the parameter. If you use two ports to connect Internet, you should configure the parameter of ISP and bandwidth.
-
Page 10: Advanced Setting
1705Router Web Configuration Manual NAT Port Mapping: It can open the some port(such as TP0) in order to make outside network accessing the router. LAN Host IP: fill in the IP address of host. WAN Port: select a port which is connected Internet( It is physical port). Services: select these services in order to make outside-network host accessing. - Page 11 1705Router Web Configuration Manual It shows WAN port name and type(such as PPPoE, Static IP, dynamic IP) of router. Click the button of port name to enter material configuration page layout. There are three configuration types for WAN port: Ethernet(static IP) If you use the IP address which is provided by ISP, you should choose this method to configure router IP address, subnet mask: fill in the IP address and subnet mask that are provided...
-
Page 12: Lan Port Configuration
1705Router Web Configuration Manual If you use ADSL dialing to browse Internet, you should choose this method. Username, password: fill in the username and password that is provided by ISP. Click “apply” to make configuration effective, click “back” to keep old configuration. 1.4.2 LAN Port Configuration Users can configure LAN port to connect LAN. -
Page 13: Nat Configuration
1705Router Web Configuration Manual Secondary IP address, subnet mask: fill in the IP address and subnet mask. Note: If the system shows the following information: It is warning: you are configuring the router through this port, and you couldn’t alter this IP address. If you click “apply”... - Page 14 1705Router Web Configuration Manual of computer. If you download something by BT, the value is more. There are 200 PC in one net-bar, about 600 is enough.) Max-entries(per host): It is used to set max-entries for each IP. Address Mapping Setting: The configuration make all users in LAN share one public IP address.
-
Page 15: Dhcp Server Configuration
1705Router Web Configuration Manual IP Subnet――one IP address and one subnet mask. Src port: it is only used in TCP or UDP protocol. Any——all ports. =,>,<,!=(unequal to )——limit the value of some port. Range——range of one section port. Typically you should select IP range in source IP to fill in PC IP of LAN, or select IP Subnet to fill in the net-segment of LAN. -
Page 16: Dns Configuration
1705Router Web Configuration Manual Lease expired: the useful-life of PC IP address. The default is one day. Click “apply” to make the configuration effective. If you want to check the distributive result, you should click “Client List”. It shows the IP address, MAC address and lease expired of client. Click “Refresh”... -
Page 17: Multiplex Line
1705Router Web Configuration Manual 1.5.1 Multiplex Line There are more WAN ports in router, and they can connect Internet at one time. You could design the flux control of port according to bandwidth of every line. You can use “ WAN Flux Setting” to achieve the control. Enable: Enable or Disable. -
Page 18: Port Mapping
1705Router Web Configuration Manual 1.5.2 Port Mapping Port mapping is one of NAT. It is used to mapping the IP address in LAN or TCP/UDP port of one IP address to public net, so that the users in public net could call some host computer or serve that are in LAN. -
Page 19: Special Address Mapping
1705Router Web Configuration Manual 1.5.3 Special Address Mapping It is one of NAT. if you configure in NAT setting menu, it could make users in inner net call public net; And configuration of port mapping could make users in public call some host computer or service in inner net. -
Page 20: Default Route
1705Router Web Configuration Manual The configuration method of filter lists is similar with access list configuration of NAT. Their difference is: access lists of NAT is used to control communication of Internet and PC in LAN, but filter lists of firewall is used to control the filter function of data packet. Note: The filter lists is a order sentence concourse, it match information of packet and parameter of access lists by superincumbent order. -
Page 21: Static Route
1705Router Web Configuration Manual Default Route: IP Addr——fill in the IP address of default route. TPx——select a port of default route. Metric: select the metric of reaching default route. The default value is 1. Usually it is used to be the default value. 1.5.6 Static Route It is used to configure the static route. -
Page 22: Ddns Settings
1705Router Web Configuration Manual Metric: the default value is 1. 1.5.7 DDNS Settings DDNS (dynamic DNS) only support “PeanutHull” at present. Click “Add” to add a piece of configuration for DDNS. Name: intitle for the setting. State: Enable or Disable. Username, Password: fill in the username and password that is registered in PeanutHull net. -
Page 23: Vpn Settings
1705Router Web Configuration Manual 1.5.8 VPN Settings The routers support VPN, and you can configure IPSec. It is used to establish a tunnel for either communication, and protect the communication of host computer between tunnel. You should ensure that configure IPSec VPN in which port. Then you could edit the list of tunnel, establish one or more tunnels. -
Page 24: Admin Tools
1705Router Web Configuration Manual ID: You can establish more tunnel, so you should point out ID of one tunnel. Local Group: it shows the IP address range of local tunnel. It must suit the IP address which is in local group so that could use IPSec. Remote Group: It is one IP, range, mask of another end tunnel. - Page 25 1705Router Web Configuration Manual Fill in the username, password and confirm password, then click “Apply” to add new username. Click “Config” to alter the password. Fill in new password and confirm, click “Apply” to alter. Note: system don’t provide delete function when there is only one user. - 23 -...
-
Page 26: Config Files
1705Router Web Configuration Manual 1.6.2 Config Files Save Current Configuration: it is used to save the current configuration for router. Current Configuration Backup: it is used to backup the configuration files. That is downloading the startup-config file to PC in order to use at meet. Load Configuration: it is corresponding to above item. -
Page 27: Time Settings
1705Router Web Configuration Manual IOS Software Backup: we issue new IOS edition in a period of time. Users could backup old edition. IOS software Upgrade: it is used to upgrade IOS edition. And users must named the file “router.bin”. The IOS file must be a rightful file. 1.6.4 Time Settings There are two parts in this page layout:... -
Page 28: Remote Control
1705Router Web Configuration Manual 1.6.5 Remote Control HTTP Server Port Setting: in some condition users may alter the default port to configure Web. You should make sure this port doesn’t conflict with other port. NAT Surveillance Software: Enable or Disable. SNMP Settings: it is used to enable SNMP function. -
Page 29: Port Define
1705Router Web Configuration Manual Source IP: it is used to appoint the especial port to ping the destination IP address. Here should be filled in the IP address of especial port. It can be choose or not. Packet Size: it is used to design the size of ping packet. 1.6.7 Port Define The router can be set more WAN port. -
Page 30: System Information
1705Router Web Configuration Manual 1.7.1 System Information It is used to show the system informatiom. 1.7.2 System State It shows the port state of system. 1.7.3 System Log Users could know the system state by observing Log information. The page layout shows the log information. Click “Clear” to clear the information, click “Refresh”... - Page 31 1705Router Web Configuration Manual System Log Output Setting Enable: it is used to enable or disable the output of system log. If you select “Disable”, the log output page layout will not show any information. Syslog Size: it is the size of log buffer. Level: The output of Log is divided into many steps.
Need help?
Do you have a question about the 1705b and is the answer not in the manual?
Questions and answers