Related Manuals for Pfaff 1183-712/02
Summary of Contents for Pfaff 1183-712/02
-
Page 1: Instruction Manual
1183 -712/02 Instruction Manual This instruction manual applies to machines from the following serial numbers onwards: 6 001 000 296-12-18 610/002 Betriebsanleitung engl. 09.04... - Page 2 As an alternative to the internet download the adjustment manual can also be ordered in book form under part no. 296-12-18 611/002. The reprinting, copying or translation of PFAFF Instruction Manuals, whether in whole or in part, is only permitted with our previous authorization and with written reference to the source.
-
Page 3: Table Of Contents
Danger .......................... 1 - 4 Proper use ........................2 - 1 Specifications ......................3 - 1 PFAFF 1183-712/02 ....................... 3 - 1 Models and subclasses ....................3 - 1 Disposal of machine ....................4 - 1 Transport, packaging and storage ................5 - 1 Transportation to customer's premises ................ - Page 4 Index Contents ................. Chapter - Page Preparation ........................9 - 1 Inserting the needle ...................... 9 - 1 Winding the bobbin thread, adjusting the thread tension ..........9 - 2 Removing/Inserting the bobbin case ................9 - 3 Inserting the bobbin case / Adjusting the bobbin thread tension ........9 - 3 Threading the needle thread / Adjusting the needle thread tension ......
-
Page 5: Safety
Safety Safety Directives This machine is constructed in accordance with the European regulations contained in the conformity and manufacturer’s declarations. In addition to this Instruction Manual, also observe all generally accepted, statutory and other regulations and legal requirements and all valid environmental protection regulations! The regionally valid regulations of the social insurance society for occupational accidents or other supervisory organizations are to be strictly adhered to! General notes on safety... -
Page 6: Safety Symbols
It is the obligation of the user to ensure that none of the safety mechanisms are removed or deactivated. It is the obligation of the user to ensure that only authorized persons operate and work on the machine. Further information can be obtained from your PFAFF agent. 1 - 2... -
Page 7: Operating And Specialist Personnel
Safety Operating and specialist personnel Operating personnel .05.01 Operating personnel are persons responsible for the equipping, operating and cleaning of the machine as well as for taking care of problems arising in the sewing area. The operating personnel is required to observe the following points and must: always observe the Notes on Safety in the Instruction Manual! never use any working methods which could adversely affect the safety of the machine! not wear loose-fitting clothing or jewelery such as chains or rings! -
Page 8: Danger
Safety Danger A working area of 1 meter is to be kept free both in front of and behind the machine while it is in operation so that it is always easily accessible. Never reach into the sewing area while sewing! Danger of injury by the needle! Never leave objects on the table while adjusting the machine settings! Objects can become trapped or be slung away! Danger of injury! 93-002... -
Page 9: Proper Use
Proper use Proper use The PFAFF 1183-712/02 is a single-needle, lockstitch, flatbed sewing machine for industrial tacking and basting work. Any and all uses of this machine which have not been approved of by the manufacturer are considered to be inappropriate! The manufacturer cannot be... -
Page 10: Specifications
Specifications Specifications PFAFF 1183-712/02 Stitch type: ....................301 (lockstitch) Needle system: ....................... 134 - 35 Needle size in 1/100 mm: ..................80 - 100 Presser foot clearance: .................... 16 mm Clearance width: ....................260 mm Clearance height: ....................125 mm Bedplate dimensions: ................... -
Page 11: Disposal Of Machine
Disposal of machine Disposal of machine The proper disposal of the machine is the responsibility of the customer. The materials used in the machines are steel, aluminium, brass and various plastics. The electrical equipment consists of plastics and copper. The machine is to be disposed of in accordance with the locally valid environmental protection regulations. -
Page 12: Transport, Packaging And Storage
Transport, packaging and storage Transport, packaging and storage Transportation to customer's premises The machines are delivered completely packed. Transport within the customer’s premises The manufacturer bears no liability for transport within the customer’s premises or to the in- dividual locations of use. Make sure that the machines are always transported upright. Disposal of the packaging The packaging of these machines consists of paper, cardboard and VCE fiber. -
Page 13: Explanation Of The Symbols
Explanation of the symbols Explanation of the symbols In the following section of this Instruction Manual, certain tasks or important pieces of information are accentuated by symbols. The symbols used have the following meanings: Note, information Cleaning, care Lubrication, greasing Servicing, repairing, adjustment, maintenance (only to be carried out by specialist personnel) 6 - 1... -
Page 14: Controls
Controls Controls On/off switch Switch the machine on or off by turning on/off switch 1. Fig. 7 - 01 Pedal Neutral position Sewing Cut thread (on machines with –900/24) Fig. 7 - 02 7 - 1... -
Page 15: Control Panel
The control panels switches on all LCD- segments and the horn automatically for a short time during the power-on phase, after which the lettering PFAFF appears on the display, until the higher-ranking control unit sends commands to the control panel. - Page 16 Controls Start backtack This function key is not used on this machine. End backtack This function key is not used on this machine. Needle position If this key is pressed the "needle raised after sewing stop" function is switched on or off. When the function is switched on, the needle positions at t.d.c.
-
Page 17: Mounting And Commissioning The Machine
Mounting and commissioning the machine Mounting and commissioning the machine The machine must only be mounted and commissioned by qualified personnel! All relevant safety regulations are to be observed! If the machine is delivered without a table, be sure that the frame and the table top which you intend to use can hold the weight of the machine and the motor. -
Page 18: Garnrollenständer Montieren
Mounting and commissioning the machine Garnrollenständer montieren .01.02 Garnrollenständer gemäß Fig. 8-02 mon- tieren. Anschließend den Ständer in die Bohrung der Tischplatte einsetzen und mit den beiliegenden Muttern befestigen. Fig. 8 - 02 8 - 2... -
Page 19: Connecting The Plug-In Connections And Earth Cables
Mounting and commissioning the machine Connecting the plug-in connections and earth cables Fig. 8 - 03 Connect all plugs as labelled to the control box 1. Screw the earth cable from the sewing head and the main switch to earth point A. Connect earth point A to earth point B with earth cable 2. -
Page 20: Start Inhibitor
Mounting and commissioning the machine Start inhibitor Mounting the start inhibitor .03.01 Set the machine into the table top. After loosening screws 2, set switch 1 so that it is activated when the sewing head is in an upright position. In this position tighten screws 2. -
Page 21: Basic Setting Of The Machine Drive Unit
Mounting and commissioning the machine Basic setting of the machine drive unit Switch on the machine. Press TE/Speed key twice to call up the input mode. By pressing the corresponding +/- key, call up parameter "798" and select service level "C", see Chapter 12.07.01 Selecting the user level. - Page 22 Mounting and commissioning the machine By operating the pedal, sew one stitch. Turn the balance wheel in the direction of sewing until the tip of the needle is level with the top edge of the needle plate. By pressing the corresponding +/- key, call up parameter "702". By pressing the corresponding +/- key, enter the value "80".
-
Page 23: Commissioning
Mounting and commissioning the machine Commissioning Examine the machine, in particular the electric cables for any damage. Clean the machine thoroughly, see also Chapter 10 Care and Maintenance. Have qualified personnel check whether the machine can be operated with the available voltage and whether it is connected properly. -
Page 24: Table Top Cutout
Mounting and commissioning the machine Table top cutout 8 - 8... -
Page 25: Mounting The Table Top
Mounting and commissioning the machine Mounting the table top 8 - 9... -
Page 26: Preparation
Preparation Preparation All regulations and instructions in this Instruction Manual are to be observed! Special attention is to be paid to the safety regulations! All preparation work is only to be carried out by appropriately trained personnel. Before all preparation work, the machine is to be separated from the electricity supply by removing the plug from the mains or switching off the On/Off switch! Inserting the needle Switch off the machine! -
Page 27: Winding The Bobbin Thread, Adjusting The Thread Tension
Preparation Winding the bobbin thread, adjusting the thread tension Fig. 9 - 02 Place an empty bobbin 1 onto bobbin shaft 2. Thread the bobbin in accordance with Fig. 9-02 and wind it anti-clockwise around bobbin 1 a few times. Switch on the bobbin winder while at the same time pressing bobbin winder spindle 2 and lever 3. -
Page 28: Removing/Inserting The Bobbin Case
Preparation Removing/Inserting the bobbin case Switch off the machine! Danger of injury due to unintentional starting of the machine! Removing the bobbin case: Tilt back the machine. Raise latch 1 and remove bobbin case 2. Inserting the bobbin case: Press bobbin case 2 until you feel it snap into the bobbin case base. -
Page 29: Threading The Needle Thread / Adjusting The Needle Thread Tension
Preparation Threading the needle thread / Adjusting the needle thread tension Fig. 9 - 05 Switch off the machine! Danger of injury due to unintentional starting of the machine! Thread the machine as shown in Fig. 9-05. Adjust the needle thread tension by turning disk 1. 9 - 4... -
Page 30: Care And Maintenance
Care and maintenance Care and maintenance Cleaning ............. daily, several times if in continuous operation Checking the oil level ................... monthly These maintenance intervals are calculated for the average running time of a single shift operation. If the machine is operated more than this, shorter intervals are recommended. -
Page 31: Topping Up The Oil Tank
Fig. 10 - 02 Only use oil with a mean viscosity of 10.0 mm /s at 40°C and a density of 0.847 g/cm at 15°C. We recommend PFAFF sewing machine oil, part no. 280-1-120 105. 10 - 2... -
Page 32: Wearing Parts
A detailed parts list for the complete machine is included with the accessories. In case of loss, the parts list can be downloaded from the internet address www.pfaff-industrial.com/de/service/download/index.php3. As an alternati- ve to the internet download the parts lists can also be ordered in book form under part no. - Page 33 Wearing parts 11-108 087-15 91-262 235-15 91-264 240-15 91-171 853-15 11-108 084-15 (2x) 91-108 222-15 99-137 151-45 91-171 049-05 91-171 042-05 11 - 2...
-
Page 34: Postfach
PFAFF Industrie Maschinen AG Postfach 3020 D-67653 Kaiserslautern Königstr. 154 D-67655 Kaiserslautern Telefon: (0631) 200-0 Telefax: (0631) 17202 E-Mail: info@pfaff-industrial.com...
Need help?
Do you have a question about the 1183-712/02 and is the answer not in the manual?
Questions and answers