Download  Print this page

Declaration Of Conformity - NEC PlasmaSync 42XM2 Model Information

Nec electronics america plasmasync plasma monitor user manual
Hide thumbs
   

Advertisement

*1 Only when using a graphic accelerator board that is capable of displaying 852 480.
*2 Display only 640 lines with the screen center of the vertical orientation located at the center.
*3 The picture is displayed in the original resolution. The picture will be compressed for other signals.
*4 Aspect ratio is 5:4. This signal is converted to a 720 dots 768 lines signal.
*5 Normally the RGB select mode suite for the input signals is set automatically. If the picture is not displayed properly, set the RGB mode
prepared for the input signals listed in the table above.
*6 To connect the monitor to Macintosh computer, use the monitor adapter (D-Sub 15-pin) to your computer's video port.
*7 Other screen modes (ZOOM and STADIUM) are available as well.
*8 When viewing a moving picture at a vertical frequency greater than 65Hz, the picture may sometimes be unstable (jumpy). If this occurs,
please set the refresh rate of the external equipment to 60Hz.
To view 480I@60Hz (480 interlaced lines, 60Hz refresh rate) or 576I@50Hz (567 interlaced lines, 50Hz refresh rate) when sync polarity
is "Sync on Green", set "RGB SELECT" to "MOTION".
NOTE:
• While the input signals comply with the resolution listed in the table above, you may have to adjust the position and size of the picture or
the fine picture because of errors in synchronization of your computer.
• This monitor has a resolution of 1024 dots 768 lines. It is recommended that the input signal should be XGA, wide XGA, or equivalent.
• With digital input some signals are not accepted.
• The sync may be disturbed when a nonstandard signal other than the aforementioned is input.
• If you are connecting a composite sync signal, use the HD terminal.
What is HDCP/HDCP technology?
HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content Protection (HDCP) is a system for
preventing illegal copying of video data sent over a Digital Visual Interface (DVI).
If you are unable to view material via the DVI input, this does not necessarily mean the PDP is not functioning properly. With the implementation
of HDCP, there may be cases in which certain content is protected with HDCP and might not be displayed due to the decision/intention of the
HDCP community (Digital Content Protection, LLC).
• "IBM PC/AT" and "XGA" are registered trademarks of International Business Machines, Inc. of the United States.
• "Apple Macintosh" is a registered trademark of Apple Computer, Inc. of the United States.

DECLARATION OF CONFORMITY

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
U.S. Responsible Party:
Address:
Tel. No.:
Type of Product:
Equipment Classification:
Models:
conforms to the technical standards as specified in the FCC Rules.
NEC SOLUTIONS (AMERICA), INC.
1250 N. Arlington Heights Road, Suite 500
Itasca, Illinois 60143-1248
800-836-0655
Plasma Display
Class B Peripheral
PX-42XM2A/S
We hereby declare that the equipment specified above
NEC Solutions (America), Inc.
1250 N. Arlington Heights Road, Suite 500
Itasca, Illinois 60143-1248
Copyright © by NEC Plasma Display Corporation
NEC and the NEC logo are registered trademarks of
8
NEC Corporation
Printed on recycled paper
Printed in Japan
7S801011

Advertisement

loading

  Related Manuals for NEC PlasmaSync 42XM2

This manual is also suitable for:

Plasmasync px-42xm2a/s42xm2sPlasmasync px-42xm2a