Programmed Play - Sanyo DC X900 Instruction Manual

CD PLAY
Use compact discs bearing the symbol shown below. In addition to
conventional 12 cm CDs, this system can be used to play 8 cm CDs
without an adapter.
W3i!i!
DIGITAL AUDIO
1.
2.
3.
4.
5.
6.
Press the CD function switch.
m
"Cd" appears on the display.
Press the OPEN/CLOSE switch.
The disc tray slides out.
m
Place the disc with the label facing up on the disc tray.
For 12 cm CD
For 8 cm CD
Press the OPEN/CLOSE switch again to close the disc tray.
ml
The total number of tracks on the disc appears.
Press the PIAY/PAUSE switch.
The PLAY indicator lights, and play starts from the first track.
m
The current track number appears.
Press the STOP switch to end disc play.
When the last track has been played, the player automatically stops.
m
1 1
When the OPEN/CLOSE switch is pressed during play, play will stop
and the disc tray will slide out.
Notes on handling compact discs
-
Do not expose the disc to direct sunlight, high humidity or high
temperatures for extended periods of time.
- Discs should be returned to their cases after use.
- Do not apply paper or write anything on the disc surface.
- Handle the disc by its edge. Do not touch the playing surface (glossy
side).
- Fingerprints and dust should be carefully wiped off the playing
surface of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
- Never use chemicals such as record cleaning sprays, antistatic sprays
or fluids, benzine or thinner to clean compact discs.
Temporarily stopping play
Press the PLAY/PAUSE switch. The PIAY indicator blinks. To resume
play, press the switch again.
Direct track selection
By using the remote control, play can be started immediately from the
desired track.
While a disc is playing, it is possible to switch immediately to a particular
track,
Proceed with the operation after the CD 10KEY switch has been pressed.
Examples:
To start from track 3 on the disc, press the 3 switch.
To start from track 10, press +1 O, then 0,
To start from track 25, press +1 O twice, then 5.
Skip piay
To skip to track 6 while track 3 is playing, press the M / W SKIP/
SEARCH switch repeatedly until "6" appears on the display.
To skip back to track 3 while track 6 is playing, press the M / * SKIP/
SEARCH switch repeatedly until "3" appears.
Search (forward/reverse)
If the w / ~ or ~ / ~ SKIP/SEARCH switch is pressed during
play, the player will search at high speed in the forward or reverse
direction while the switch is being pressed. When the switch is released,
normal play will continue.
- During search operation, the display indicates the elapsed playing
time of the track which is searching. The left-hand digit indicates the
last place of minutes and the right-hand digit indicates ten's place of
seconds.
Examples:
15 minutes 30 seconds
m
1 minute 32 seconds
D
Random piay
Press the RANDOM switch on the remote control to begin random play.
The playerwill automatically select and play tracks on the disc at random.
The PIAY and RANDOM indicators light.
If the RANDOM switch is pressed during random play, the player w;"
select the next random track.
Repeat piay
Before or during play, press the REPEAT switch. The player will play all
the tracks, all the programmed tracks or all the random play tracks
repeatedly. The REPEAT indicator lights.
To cancel repeat play, press the REPEAT switch again. The REPEAT
indicator goes out.
PROGRAMMED PLAY
Up to t 6 selections on a disc can be programmed for play in any order.
- To begin the programming procedure, select the CD function first.
- The same track can be programmed more than once.
Example:
To programme tracks 5,2,6 and 10 (using the remote control)
1.
2.
3.
4.
5.
6.
Proceed with the operation after the CD 10KEY switch has been
pressed.
Press the MEMORY switch. The PROGRAM indicator lights and "1"
blinks on the display.
Select track 5 by pressing the 5 switch. "5" blinks.
Press the MEMORY switch. "5" remains lit.
Select track 2 by pressing the 2 switch. "2" blinks.
Press the MEMORY switch. The PROGRAM indicator and "2" remain
lit.
- The remaining tracks are programmed in the same way.
Press the /II switch to start play.
When all programmed selections have played, the player stops
automatically.
- The programme contents are retained in memory,
The tracks can also be selected using the ~ or ~ switch.
When programming using the controls on the main unit, use the SKIP/
SEARCH
switches to assign the tracks.
Any attempt to programme more than 16 selections will result in
discontinuation of the programming.
The programme is cleared in the following cases:
- When the STOP switch is pressed in the stop mode
- When the EDIT switch is pressed in the stop mode
- When the OPEN/CLOSE switch is pressed
- When other source is selected
- When the power is switched off
-7-