NEC MultiSync LCD2180UX User Manual page 53

Appendix
Color Control
Tag6
Tag7 Sharpness
Expansion Mode
Video Detect
DVI Selection
Off Timer
Language
OSM Position
OSM Turn off
LCD2180UXManual1020.p65
–continued
Color Control Systems: Six color presets select the desired colour setting (sRGB,
NATIVE and PROGRAMMABLE color presets are standard and cannot be changed).
Color temperature increases or decreases, in each preset.
R,Y,G,C,B,M,S: Increases or decreases Red, Yellow, Green, Cyan, Blue, Magenta and
Saturation depending upon which is selected. The change in color will appear on screen
and the direction (increase or decrease) will be shown by the color bars.
NATIVE: Original color presented by the LCD panel that is unadjustable.
PROGRAMMABLE: The color temperature and tone that were set up with the
downloaded application software are reflected.
This is a digital capability for keeping a crisp image at all signal timings. It continuously
adjusts to maintain a distinct or soft image as you prefer, and is set independently
according to different timings.
The number of adjustment steps is different depending on whether the mode is OFF,
FULL or ASPECT (1600 x 1200 is OFF Mode). Press "+" or "-" to adjust.
Sets the zoom method.
FULL: The image is expanded to 1600 x 1200, regardless of the resolution.
ASPECT: The image is expanded without changing the aspect ratio.
OFF: The image is not expanded.
CUSTOM (Digital input and Resolution of 1600 x 1200 only):
Select one of nine expansion rates. In this mode, the resolution may be low and there
may be blank areas. This mode is for use with special video cards.
Press "SELECT" to move the select menu, and press "+" or "-" to select.
Selects the method of video detection when more than one computer is connected.
Press "+" or "-" to select.
FIRST DETECT: The video input has to be switched to "FIRST DETECT" mode. When
current video input signal is not present, then the monitor searches for a video signal from
the other video input port. If the video signal is present in the other port, then the monitor
switches the video source input port to the new found video source automatically. The
monitor will not look for other video signals while the current video source is present.
LAST DETECT: The video input has to be switched to the "LAST DETECT" mode. When
the monitor is displaying a signal from the current source and a new secondary source is
supplied to the monitor, then the monitor will automatically switch to the new video source.
When current video input signal is not present, then the monitor searches for a video
signal from the other video input port. If the video signal is present in the other port, then
the monitor switches the video source input port to the new found video source automatically.
NONE: The Monitor will not search the other video input port unless the monitor is turned on.
This function selects the DVI input mode (Input 1). When the DVI selection has been
changed, you must restart your computer. Press "+" or "-" to select.
AUTO: By using the DVI-D to DVI-D cable, the DVI SECTION is DIGITAL.
By using the D-SUB to DVI-A cable, the DVI SECTION is ANALOG.
DIGITAL: DVI digital input is available.
ANALOG: DVI analog input is available.
Monitor will automatically power-down when the end user has selected a pre-determined
amount of time.
OSM control menus are available in seven languages. Press "+" or "-" to select.
You can choose where you would like the OSM control image to appear on your screen.
Selecting OSM Location allows you to manually adjust the position of the OSM control
menu left, right, down or up. Press "SELECT" to move the adjustment menu, and press
"+" or "-" to adjust.
The OSM control menu will stay on as long as it is in use. In the OSM Turn Off submenu,
you can select how long the monitor waits after the last touch of a button to close the
OSM control menu. The preset choices are 10-120 seconds in 5 second increments.
Press "+" or "-" to select.
51
51 10/21/03, 9:11 AM