Initial Setup - OK. OLE 396 B-D4 User Manual

Chapter 3

Initial setup

Initial setup involves selecting all the settings
required to be able to search for and store all the
analogue and digital channels you can receive.
Make sure that the television is switched on and
follow all the steps in turn specified hereafter.
Note: If the channel search retrieved only the
analogue channels it could be caused by poor
broadcasting and therefore is not covered
by manufacturer warranty. Manufacturers
cannot be held responsible for lack of or poor
broadcasting in some areas.
The first time you switch the set on, the Initial
setup wizard opens, which guides you through
the initial setup process. (Refer to Figure 1.)
1. Press ▲/▼ to select your language, then press
OK/► to enter the next step.
2. Press ▲/▼ to select your country, then press
OK/► to enter the next step.
Note: If you select France, you will have to
enter the Password setting menu here in
order to set a password. Use the
buttons to enter a four-digit number for
your password. (0000 is too simple to
be set as your password.) Re-enter the
same code to confirm the password.
After that, you will enter the next step
automatically. (In this step, you can only
press ◄ to return to the previous step.)
3. Press ▲/▼ to select your tuner mode
Antenna Cable.
or
Antenna.
- Select
• P ress OK/► to enter.
• P ress ▲/▼ to select Scan, then press OK/►
to start the automatic search for all DVB-T
digital and/or analogue
Cable.
- Select
• Press OK/► to enter.
• P ress ▲/▼ to select Scan, then press OK/►
to directly start your initial setup or enter
below step.
• S elect Full if available to search for and store
all DVB-C digital and analogue channels.
• Y ou may select another advanced
scan mode if available (for example,
Advanced), then configure
cable information as described below. Use
the numeric buttons to adjust the values
for frequency, symbol rate and network
ID; use ◄/► to select a modulation mode.
• P ress OK to start initial setup relating to
all DVB-C digital and analogue channels.
Note: To prevent the channel setup process from
being interrupted, wait for the message
indicating that the setup is complete.
4. Before starting the scanning, you can also select
Skip scan to skip the initial setup process.
numeric
channels.
the correct
EN 8
5. During the setup, you can follow the hints
available at the bottom of the screen to return
to the previous step by pressing ◄. Or press
Exit to exit or interrupt the search halfway.
6. Once the automatic search ends, the set
enters the next step automatically. Press ▲/▼
to select your location Shop or Home. Press
OK/► to confirm your selection and enter the
last step.
7. - In this step, you can press OK to exit the
initial setup. The channels are arranged in
a preset order. If you wish to skip channels,
modify the preset order or rename channels,
select Setup > Organiser and press OK/► to
enter.
- In this step, you can also press ◄ to return to
the previous step.
Performing an automatic channel search
This section describes how to search and store
channels automatically. Instructions are for both
analogue and digital channels.
1. Press Menu on the remote control and select
Setup > Language > Menu language. Press
◄/► to select your desired menu language.
2. Press Menu to return to Setup, press ▲/▼ to
select Country, then press ◄/► to select your
country. The TV installs and arranges channels
according to your country.
3. Press ▲/▼ to select Tuner mode, then
press ◄/► to select
Antenna.
- Select
• P ress ▲/▼ to select Channel install, and
press OK/► to enter.
• S elect Automatic search (Refer to
Figure 2.), then press OK/► to display
Automatic search.
• P ress OK to skip the country selection and
enter the next step. Or use ◄/► to reselect
your country, then press OK to enter.
• S elect Digital & Analogue, Digital or
Analogue, then press OK/► to start the
automatic search, which relates to all DVB-T
digital and/or analogue channels.
Cable.
- Select
• P ress ▲/▼ to select Channel install, and
press OK/► to enter.
• S elect Automatic search, then press OK/►
to display Automatic search.
• P ress OK to skip the country selection and
enter the next step. Or use ◄/► to reselect
your country, then press OK to enter.
• - S elect Digital & Analogue, then press
OK/► to enter. Select your scan mode
if available and configure proper cable
information in the same way as in Initial
setup. Select Scan and press OK/► to
start your automatic search relating to all
DVB-C digital and analogue channels.
Installing channels
Antenna Cable.
or