How Your Oster® Blender Works; Care And Cleaning - Oster BLSTTG-PB0 Instruction Manual

1
. Place ingredients into jar according to your recipe. For best results always add liquids first
when blending.
2. Place lid with filler cap on jar.
3. Plug the power cord into appropriate electrical outlet.
Push Buttons Models (models BLSTTG‑PB0 & BLSTTG‑PW0 only)
a. Select between high ( ) and low ( ) speeds by pushing the respective button of your choice.
b. Push the desired speed button following the chart below:
c. Press the off button ( ) to stop the blender.
d. To use pulse, select between high ( ) and low ( ). Push the pulse button ( ) and hold down for
desired length of time. Release the pulse ( ) button and allow blade to stop. Repeat cycle as desired.
1 2
STIR PURÉe
LOW SPeeDS ( )
electronic Models (models BLSTTG‑eB0 & BLSTTG‑eR0 only)
a. Touch the "POWeR" button to turn the product on. The LeD Indicator will flash red (and continue
to flash) indicating it is ready to operate. You are now ready to blend. Avoid contact with
blades and moveable parts.
b. Scroll up or down to select desired speed and press the "start /stop" button to blend ingredients
to desired consistency.
c. To stop blending, press the "start /stop" or "POWeR" button. The motor will come to a stop.
(Pressing the "POWeR" button stops the motor and turns off the blender.)
d. You can move between speeds at any time while blending by pressing scroll up or down
to select desired speed and press the "start /stop " button to blend ingredients to desired
consistency. The new speed will start without interruption.
e. Pressing the "PULSe" Button will give a momentary pulse at the speed indicated by the green
light. Pulsing feature is available at any of the speed options. The motor will then stop.
f. To Pulse, select desired speed setting then press the "PULSe" button to activate the blender in
short intervals at the desired speed selected. The blender will run at selected speed as long as
you press the button. The motor will stop when you stop pressing the button.
Blender jar parts are corrosion resistant, sanitary and easily cleaned. Before first use and after every use,
separate jar parts and clean thoroughly in warm, soapy water, then rinse and dry well. Use a damp, soft
sponge with mild detergent to clean the outside of the Blender base. All parts except for the Blender base
are dishwasher safe. Threaded Bottom Cap are top rack dishwasher safe ONLY. Place Sealing Ring in
bottom basket of dishwasher. You can also wash the parts in warm, soapy water. Rinse well and dry.
Periodically check all parts before re‑assembly. If the processing blades are stuck or difficult to turn,
DO NOT USE bLENDER. Check by carefully turning the blades in a counterclockwise direction
(opposite edges are sharp). Blades should turn freely.
If the jar is chipped or cracked, DO NOT USe BLeNDeR. Further use could result in the jar breaking
during use. Use only OSTeR
Service Center.
USE OF DAmAgED OR NON‑RECOmmENDED PARTS COULD RESULT IN SEvERE
PERSONAL INJURY AND/OR DAmAgE TO THE bLENDER. See Page 4 for proper jar assembly
and user instructions.
NEVER IMMERSE THE MOTOR BASE IN WATER. The housing can be cleaned with a damp
cloth (unplug first). The motor is permanently lubricated and does not require any additional lubrication.
ANY SERVICING SHOULD BE PERFORMED BY AN AUTHORIZED SERVICE FACILITY.
HOw YOUR OSTER®
BLENDER wORKS
3 4
CHOP WHIP

CARE AND CLEANING

Blender recommended replacement parts available at an Authorized
®
5 6
PULSe GRATe
E n g li s h - 6
7 8
BLeND GRIND LIQUIFY
HIGH SPeeDS ( )
9 10
ICe
CRUSH