Advertisement

Quick Links

CompactRIO PROFIBUS DP
Installation Instruction
V1.6/03.03.2010
© COMSOFT
CompactRIO PROFIBUS DP-Installation Instruction- V1.6/03.03.2010

Advertisement

Table of Contents
loading

Summary of Contents for Oster BLSTMP-WOO

  • Page 1 CompactRIO PROFIBUS DP Installation Instruction V1.6/03.03.2010 © COMSOFT CompactRIO PROFIBUS DP-Installation Instruction- V1.6/03.03.2010...
  • Page 2 d:\windoc\icp\project\5362_crio-dp_master\anwenderdoku\installation\version_1.6\crio_pb_e.doc Revision History Version Date Description Resp. V1.6 03.03.2010 Minor Fixes V1.5 16.02.2010 National Instruments specific changes SF, JK V1.4 23.09.2009 Technical data table updated V1.3 07.05.2009 Technical data table updated V1.2 28.04.2009 Technical data table updated V1.1 20.08.2008 Technical data table updated V1.0 21.02.2008 Initial Version COMSOFT GmbH...
  • Page 3: Table Of Contents

    Installation Instruction Contents Contents Installation of the Module....................1 LEDs and Connectors ....................2 Position of LEDs and Connectors.................2 LED's ........................3 Power connector ....................4 9 pin SUB D connector..................4 Technical Data ......................5 Use in hazardous locations ..................5 CE- Conformity Declaration...................6 © COMSOFTCompactRIO PROFIBUS DP-Installation Instruction-V1.6/03.03.2010 Business Confidential/COMSOFT Proprietary...
  • Page 4 Contents Installation Instruction List of Figures Figure 1: cRIO PB module......................1 Figure 2: LEDs and connectors ....................2 Figure 3: Profibus-Terminator (cable type B is no longer used) ..........4 List of Tables Table 1: Meaning of the LEDs ....................3 Table 2: Power requirements....................4 Table 3: Pin Assignment 9 pin SUB D connector..............4 Table 4: Technical Data......................5 CompactRIO PROFIBUS DP-Installation Instruction-V1.6/03.03.2010©...
  • Page 5: Installation Of The Module

    Installation Instruction Installation of the Module 1 Installation of the Module The cRIO PB module is a PROFIBUS DP Master/Slave module for National Instruments CompactRIO, Single-Board RIO systems. The configuration entirely takes place by means of the delivered software. Thus, no jumpers or DIP-switch adjustments are necessary. To mount the module in the CompactRIO or Single-Board RIO proceed as follows: •...
  • Page 6: Leds And Connectors

    LEDs and Connectors Installation Instruction 2 LEDs and Connectors 2.1 Position of LEDs and Connectors RUN - PROFIBUS Activity LED PWR - Power indication LED BF - PROFIBUS Bus Fail LED SPI - Activity LED Power – Power supply connector (plug within scope of delivery) DP –...
  • Page 7: Led's

    Installation Instruction LEDs and Connectors 2.2 LED's Colour State Function Green No power supply connected Power supply connected Green SPI bus not active SPI bus active Green Operation as DP-Master Scanning not activated Scanning activated Operation as DP-Slave DP Slave not active DP Slave initialized Flash DP Slave (AutoSlaveMode)
  • Page 8: Power Connector

    LEDs and Connectors Installation Instruction 2.3 Power connector Parameter Value Nominal value 24 Volts DC Input range 11 – 30 Volts DC Power consumption 2.5 W in Active mode (Receiving and Transmitting) Table 2: Power requirements 2.4 9 pin SUB D connector Pin Number Signal Function...
  • Page 9: Technical Data

    Installation Instruction Technical Data 3 Technical Data Processor ARM 9 at 150 MHz Profibus Controller ASPC2 at 48 MHz Memory 32 Mbyte SRAM 4 Mbyte Flash Type Memory SPI Interface SPI Slave up to 4 Mbit/s Profibus Interface 1 Port (Sub-D 9 pins) Interface Physics RS485 (isolated) Profibus Data Rates...
  • Page 10: Ce- Conformity Declaration

    CE- Conformity Declaration Installation Instruction 4 CE- Conformity Declaration We herewith declare that the CompactRIO Module cRIO PB corresponds to the requirements stated in the EU standards 2004/108/EG. The device corresponds to the following standards: DIN EN 55024, issue 2003-10 DIN EN 55022, issue 2007-04 Manufacturer: COMSOFT GmbH...

This manual is also suitable for:

Blstmg-woo

Table of Contents