Step 2: Connecting The Video Cords/Hdmi Cord - Sony RDR-GX350 Service Manual

QQ
3 7 63 1515 0
A: Connecting a set top box receiver
With this hookup, you can record any programme position on the set top box receiver.
To watch cable programmes, you need to match the programme position on the recorder to the
aerial output programme position on the set top box receiver.
Wall
Aerial cable*
(not supplied)
to AERIAL IN
to AERIAL OUT
Aerial cable
(supplied)
: Signal flow
*1
If your set top box receiver does not have an aerial output jack, connect the aerial cable to the recorder's
AERIAL IN jack.
*2
Connect only if your set top box receiver has a SCART connector.
TE
L 13942296513
14

Step 2: Connecting the Video Cords/HDMI Cord

Select one of the following patterns, A through E, according to the input jack on your TV
monitor, projector, or audio component such as an AV amplifier (receiver). This will enable
you to view pictures.
B
TV, projector, or audio
component
to LINE 2 OUT
(VIDEO)
(yellow)
(blue) (red)
(green)
to COMPONENT
VIDEO OUT
Component video
cord (not supplied)
(green) (blue) (red)
www
D
TV, projector, or audio
component
.
: Signal flow
16
http://www.xiaoyu163.com
Place the set top box controller
near the remote sensor on the
set top box receiver.
Set top box
controller
Set top box (page 13)
receiver
ANT IN
TO TV
1
SCART cord* 2
(not supplied)
to G-LINK
DVD recorder
TV
to aerial input
TV
Audio/video
cord (not
supplied)
SCART cord (not supplied)
to T LINE 3 – TV
DVD recorder
to LINE 2 OUT to HDMI OUT
(S VIDEO)
S-video cord HDMI cord
(not supplied) (not supplied)
C
x ao
y
TV, projector, or audio TV, projector, or audio
component component
i
http://www.xiaoyu163.com
8
B: Connecting the aerial cable only (no set top box receiver)
Use this hookup if you watch cable programme position without a set top box receiver. Also
use this hookup if you are connecting only an aerial antenna.
With this hookup, you can record any programme position by selecting the programme position
on the recorder.
Wall
: Signal flow
Q Q
3 6 7 1 3
A SCART input jack
When setting "LINE 3 Out" to "S-Video" or
"RGB" in the "Video In/Out" setup
(page 115), use a SCART cord that conforms
to the selected signal.
B Video input jack
You will enjoy standard quality images.
A
C S VIDEO input jack
You will enjoy high quality images.
D Component video input jacks (Y, P
P /C )
R R
You will enjoy accurate colour reproduction
and high quality images.
If your TV accepts progressive 525p/625p
format signals, use this connection and set
"Progressive" to "Compatible" in the "Easy
Setup" setup (page 23). Then set
"Component Video Out" to "Progressive" in
the "Video In/Out" setup to send progressive
video signals. For details, see "Component
Video Out" on page 115.
E HDMI input jack
Use a certified HDMI cord (not supplied) to
enjoy high quality digital picture and sound
through the HDMI OUT jack.
When connecting a Sony TV that is
compatible with the HDMI control function,
see page 18.
To see the signals from the connected set top
box receiver when the set top box receiver is
connected to the recorder using a SCART
cord only, turn the recorder on.
When connecting to the HDMI jack
Follow the steps below. Improper handling
may damage the HDMI jack and the
connector.
1
Carefully align the HDMI jack on the
rear of the recorder and the HDMI
E
connector by checking their shapes.
Make sure the connector is not upside
down or tilted.
u163
.
Connector is upside down
1-3
2 9 9 4 2 8
to AERIAL IN
to AERIAL OUT
TV
to aerial input
Aerial cable (supplied)
1 5 0 5 8 2 9 9 4
2
Insert the HDMI connector straight into
the HDMI jack.
Do not bend or apply pressure to the
HDMI connector.
b
Notes
/C ,
B B
• Be sure to disconnect the HDMI cord when
moving the recorder.
• Do not apply too much pressure to the cabinet
wall, if you place the recorder on the cabinet with
the HDMI cord connected. It may damage the
HDMI jack or the HDMI cord.
• Do not twist the HDMI connector while
connecting to or disconnecting from the HDMI
jack to avoid damaging the HDMI jack and
connector.
When playing "wide screen" images
Some recorded images may not fit your TV
screen. To change the picture size, see
page 122.
If you are connecting to a VCR
Connect your VCR to the LINE 1/
DECODER jack on the recorder (page 26).
b
Notes
• Do not connect more than one type of video cord
between the recorder and your TV at the same
time.
• Do not make connections A and E at the same
time.
• When you connect the recorder to your TV via the
SCART jacks, the TV's input source is set to the
recorder automatically when you start playback.
If necessary, press the TV t button on the
remote to return the input to the TV.
• If you connect the recorder to a TV with
SMARTLINK, set "LINE 3 Out" to "Video" in
the "Video In/Out" setup.
m
• You cannot connect the HDMI OUT jack
(connection E) to DVI jacks that are not HDCP
compliant (e.g., DVI jacks on PC displays).
• Component video and RGB signals are not output
co
when using the HDMI connection.
* This DVD recorder incorporates High-Definition
Multimedia Interface (HDMI™) technology.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
Not straight trademarks of HDMI Licensing LLC.
9 9
DVD recorder
2 8 9 9
15
,continued
17