Pioneer DV-380-S Service Manual page 63

5
No. Symptoms
QQ
4 A tray cannot be opened.
3 7 63 1515 0
(An opening screen is
displayed on the monitor)
5 Playback impossible
(no focusing)
6 Playback impossible
(Spindle does not turn)
TE
L 13942296513
7 Playback impossible
(Playback stops)
8 Picture disturbance during
playback
(block noise, freeze, other)
9 No sound
(Picture is normal)
www
.
5
http://www.xiaoyu163.com
6
Does the voltage of CP2302-pin 3 and pin 1 on the DVD MT Assy
change normally ?
Pin 5 (SW2(TRIN)): Tray is fully closed: "L"
Pin 3 (SW1(TROUT)): Tray is fully opened: "L"
Is a LOAD-DRV signal reaching ?
Are the signals output from IC101-pin 36 and pin 37 (CN103-pin 1 and
pin 2) on the DVDM Assy ?
Pin 4: Approx. 45V during opening tray approx. 0V during closing tray.
Pin 5: Approx. 0V during opening tray approx. 4.5V during closing tray.
Are wires of CP2302 and CP2303 on the DVDM Assy disconnected or
damaged ?
Does the voltage of CD2301-pin 5 change by pressing the Inside
switch.
Are the signals output from IC2301-pin 9 (F+) and pin 8 (F–) on the
DVDM Assy ?
Does 650-nm LD emit light ?
Does a pickup lens move up / down ?
Does an actuator spring bend ?
Are plastic parts damaged ? Or is a shaft detached ?
Is the turntable detached or tilted ?
Is flexible cable of CP2301 on the DVD MT Assy disconnected or
damaged ?
Is signal output from IC4002-pin 42 (FOSO) on the DVDM Assy ?
(Device control of about 1.4 V is output usually. It is fluctuated by about
± 250 mV with focus up / down.)
Are the signals output from IC2301-pin 10 (MOT SPDL–), and pin 11
(MOT SPDL+) on the DVD MT Assy ?
Is pin 33,34 (STBY) fixed LOW?
Is there any part detached from the spindle motor ?
Or Is there any foreign object lodged in it ?
Are wires of CP2303 on the DVD MT Assy disconnected or damaged ? Flexible cable / connector
Is signal output from IC4002-pin 37 (DMSO) on the DVDM Assy ?
Does 650-nm LD deteriorate ?
If the voltage at each both ends of R2303 and R2305 on the DVD MT
Assy is 0.4 V or more, the 650-nm LD is definitely deteriorated.
Does 780-nm LD deteriorate ?
If the voltage at each both ends of R2302 and R2304 on the DVD MT
Assy is 0.4 V or more, the 780-nm LD is definitely deteriorated.
Are there scratches or dirt on the disc ?
Are there scratches or dirt on the disc ?
Is there a problem with the format of the disc ?
Check the waveform (ABCK, ALRCK, ACLK, ASDATA).
Is signal output from IC8004-pin 7 and pin 8 on the DVD MT Assy ?
x ao u163
y
i
6
http://www.xiaoyu163.com
7
Diagnosis Contents
2 9
8
Q Q
3 6 7 1 3 1 5
co
.
DV-380-S
7
8
Possible Defective Points
9 4 2 8
Tray SW
DVD MT PCB Assy
DVD IC (IC4002)
DVD MT PCB Assy
FTS Driver IC (IC2301)
Connector / cable
Inside switch
DVD MT PCB Assy
FTS Driver IC (IC2301)
Pickup
Mechanism section (motor)
Flexible cable / connector
DVD MT PCB Assy
DVD IC (IC4002)
DVD MT PCB Assy
FTS Driver IC (IC2301)
Mechanism section
(Spindle motor)
DVD MT PCB Assy
0 5 8 2 9 9 4 2 8
DVD IC (IC4002)
650-nm LD deteriorated.
(When playback of a DVD is
impossible)
780-nm LD deteriorated.
(When playback of a CD is
impossible)
Disc
Disc
DVD MT PCB Assy
DVD IC (IC4002)
DVD MT PCB Assy
Audio Dac IC (IC8004)
m
9 9
A
B
C
9 9
D
E
F
61
8