Related Manuals for Pacific Wolverine PF7
Summary of Contents for Pacific Wolverine PF7
- Page 1 PACIFIC Wolverine PF7 Edger Sander From Serial Number 04453 (110 Volt) OWNERS MANUAL & OPERATING INSTRUCTIONS MAY 2010 REF. 69 PART # 000510...
- Page 2 NORTH AMERICAN SAFETY INSTRUCTIONS WARNING: This floor sanding machine must be grounded. This floor-sanding machine shall be grounded while in use to protect the operator from electric shock. The machine is provided with a three-conductor cord and a moulded three-contact grounding type attachment plug to fit the proper grounding type receptacle.
-
Page 3: Table Of Contents
SPARE PARTS Use Pacific Floor Care genuine spare parts only for service and repair. Use of non-approved parts will void the product warranty. See the back cover of this manual for the terms and conditions of the Pacific Floor Care Limited Warranty. -
Page 4: Specification
SPECIFICATION SAFETY The Pacific Wolverine PF7 Edger Sander will sand For safety it is recommended that a residual current circuit breaker (ground fault interrupter) hard and soft wood floors, cork and composition is used with this machine. floors and any solid wood surface that requires rapid sanding and leveling to a fine finish. -
Page 5: Set Up
Take care when lifting and Where possible remove all furniture from the carrying the machine. area or room. The Pacific Wolverine PF7 Edger Sander features an efficient dust pickup, however, To prepare the floor sander for use place the some dust will escape. -
Page 6: Edger Sander
Never leave the floor sander unattended with a dust bag in place containing dust. CAUTION - the Pacific Wolverine PF7 10. On completion disconnect the power cable from Edger Sander is a powerful machine. the supply. Remove and dispose of the paper Always ensure you have a firm grip dust bag, or empty the cloth bag as detailed in 7. -
Page 7: Hand Sanding
Start the sander with the drum off the Complete the first cut with the Pacific Rhino PFS 8 floor then walk forward at an even pace and ease the Drum Sander then sand up to the baseboards and drum on to the floor. - Page 8 FLOOR SANDING TECHNIQUE Level uneven floors. sanded boards unsanded boards level very uneven floors by sanding diagonally in both directions Plank and Strip Floors - sand in the Sand main floor area. direction the boards are laid, with the wood grain. unsanded boards Parquet and Wood Block Floor sand in the direction of the main...
-
Page 9: Abrasive Paper Guide
FLOOR SANDER ABRASIVE GUIDE Abrasive Grade Floor Type and Condition For removing surface coatings from old floors such as varnish, stains and wax Grit P24 Open Coat polishes. For the rapid sanding and removal of scratches and marks. Sanding (Very Coarse non-glogging) level the joints of sub-flooring like particle board and masonite. -
Page 10: General
In the unlikely event that a bearing electrical tool or appliance statutory safety tests has to be replaced use a Pacific Floor Care must be carried out by a competent person and genuine spare part only as the grease contained recorded (see Testing for Electrical Safety page 7 in the bearings is special. -
Page 11: Sanding Pad Removal & Replacement
To replace the motor Brushes Ref.12. Sanding Pad Remove the four Screws Ref.1 from the It is very important to maintain the Pacific Wolverine Cover Motor and lift the cover off. PF7 Edger Sander sanding pad in perfect condition for score free sanding and to maximize the life of the Remove the four Spring Brush Ref.17 and... -
Page 12: Sanding Pad Trimming
floor sander abrasive (120 grit) face up to a solid Reasons for Trimming the Sanding Pad flat board that is large enough to stand on and As part of routine maintenance. operate the edger. Place the board on a flat even floor and the edger on top of the board with the The sanding pad has been damaged. -
Page 13: Adjusting The Castors
Adjusting the Castors Electrical Testing. The castors are set to achieve the correct contact area across the sanding pad as illustrated in the CAUTION - testing for electrical safety diagrams above. should only be undertaken by a competent person and all results To check the castor setting place a clean sheet of recorded. -
Page 14: Trouble Shooting
TROUBLE SHOOTING FAULT CAUSE ACTION The machine does not run. The power cable is not Connect the power cable to the connected to the power supply. power supply. The motor brushes are worn. Replace the motor brushes. The voltage is too low. Check the main power complies with the machine's serial plate data. -
Page 15: Wolverine Parts Drawing
WOLVERINE PF7 PARTS DIAGRAM PACIFIC Wolverine PF7 Edger Sander From Serial Number 00466 (110 Volt) OWNERS MANUAL & OPERATING INSTRUCTIONS MAY 2010 REF. 69 PART # 000510... -
Page 16: Wolverine Parts List
WOLVERINE PF7 PARTS LIST Ref. PSTK Pack Description Ref. PSTK Pack Description Qty. Qty. R010010 4 Screw R010610 3 Screw R011610 1 Switch 110/120 Volt (Bias Off) R010620 1 Guard Disc R010050 1 Cover Motor R010630 1 Retainer R010070 1 Housing Motor... -
Page 17: Wolverine Circuit Diagram
WOLVERINE PF7 CIRCUIT DIAGRAM GREEN BLACK WHITE... -
Page 18: Service & Repair
Should any part fail in the period of two years from the date of the original purchase as a result of a defect, Pacific Floor Care will (at it’s option) either repair or replace the part without charge provided that the machine has been operated in accordance with the Owners Manual and Operating Instructions.