Accessing The Programming Mode - Viking E-30 Technical Practice

B. Wiring the E-30 Phone Board
Optional C-2000B Advanced Door
Entry Controller, DOD# 156
(not included)
VIKING
MODEL C-2000B
©
VIKING
ELECTRONICS
HUDSON, WI 54016
ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER
1 2 3 4 5 6 7 8 9 1 0 11 12 13 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
J7- J8- J9- J10- J11-
1 3 1 2 1 2 3 1 2 3 3
2 3 1 2
LED1 LED2
LED3 C LED4 C LED5 C LED6 C LED7 C
C C
* Note: When installing a line powered phone on a low voltage and/or low loop current phone system extension, a TBB-1B Talk Battery Booster may be
required, see DOD# 632.
** Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a maximum insulation of 0.082
inches. Cut off bare wire ends prior to terminating.
*** Note: To increase surge protection, loosen the PCB mounting screw labeled
from the mounting screw to Earth Ground (grounding rod, water pipe, etc.)
P r o g r a m m
P r o g r a m m
A. Accessing the Programming Mode
The E-30 phone can be programmed from any Touch Tone phone using a C.O. line, analog PABX/KSU station, or a
DLE-200B Line Simulator. For more information on the DLE-200B, see DOD# 605.
1. Using the Security Code
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls - see section H).
Step 2. From a Touch Tone phone call the line attached to the E-30.
Step 3. When the E-30 answers, enter the 6-digit security code (factory set to 845464 - see section C). A double beep
should then be heard indicating you have entered the programming mode.
2. Without the Security Code
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls - see section H).
Step 2. Move DIP switch 3 to OFF (incoming calls enter the programming mode without security code - see section H).
Step 3. From a Touch Tone phone call the line attached to the E-30.
Step 4. When the E-30 answers, a double beep will be heard and you will automatically enter the programming mode.
Step 5. When finished programming, move DIP switch 3 back to the ON position (see section H).
Warning: Failure to do step 5 above will cause the E-30 to call Viking Technical Support instead of your programmed number.
Note: If a valid memory position is entered, a double beep will be heard, four beeps indicate an error.
B. Quick Programming Features
First speed dial number ...........................................................................................
Second speed dial number ......................................................................................
Third speed dial number ..........................................................................................
Fourth speed dial number ........................................................................................
Fifth speed dial number ...........................................................................................
Q
To add a at any point in the dialing string ...............................................................
To add a # at any point in the dialing string ...............................................................
To add a four second pause at any point in the dialing string ....................................
Miscellaneous options (factory set to 000210) .........................................................
Timing/Dialing options (factory set to 234721) .........................................................
Change security code (factory set to 845464) .........................................................
Exit programming and disconnect ...........................................................................
Reset all programming to factory default settings ....................................................
4
Optional C-200 or C-250 Basic
Single Entry Phone Interface,
DOD# 169 or 172 (not included)
VIKING
MODEL C-200
©
VIKING
ELECTRONICS
HUDSON, WI 54016
SINGLE ENTRY PHONE
CONTROLLER
PABX/KSU
1 2 3 1 2 3 4 5 6 7 8 9 10 11 12
ON
1 2 3
EARTH C.O. LINE OUT TO ENTRY N.O. COM N.C. AUX POWER
GND INPUT PHONES PHONE AUX CONTACTS OUTPUT
or
i n g
i n g
Rear View of
the E-30
* C.O. Line
or Analog
Station
** Gel-Filled
Butt Connectors
Red (Ring)
or
Green (Tip)
(as shown above) and fasten a wire with spade terminal (included)
5.0"
3.63"
ON ON
1 1 2 2
ON
1 2 3
Enter Digits - then - Enter Memory Location
0-20 digits then
0-20 digits
then
0-20 digits then
0-20 digits
then
0-20 digits then
QQ
Q
#
Q
7
6 digits (0-9) then
then
6 digits (0-9)
6 digits (0-9) then
#7
###
5.0"
Ring
3.63"
Terminal
(included)
*** Earth
Ground
(optional)
#00
#01
#02
#03
#04
#17
#18
#19