VERY IMPORTANT Failure to read and follow these instructions before you proceed may result in engine damage and the voiding of your warranty.
Page 3
Failure to do so may cause damage to the Saito This instruction manual has been engine and/or the airframe. Install developed to ensure optimum per-...
Page 4
NTRODUCTION DO NOT USE HANDS, FINGERS they do not fall into the propeller. OR ANY OTHER PART OF THE BODY TO STOP THE 4. Glow plug clips and cords are PROPELLER. kept away from the propeller. DO NOT THROW ANY OBJECT INTO A PROPELLER TO STOP 5.
Igniting Glow Plugs Your It's important to be able to identi- glow plugs may be properly heat- fy the parts of your Saito engines. ed by several different sources. In this manual you'll find an The FA-90R3, FA-170R3, FA- exploded view of Saito...
Page 6
Attach the the gear (or other toggle-activated black (ground) lead to the motor switch) channel in the receiver. mount. The FA-90R3, the FA- Adjust the travel of the selected 170R3 and FA-200R3 have one channel so that the servo arm plug per cylinder.
Page 7
There are a variety of electric starters on the market. The Hangar 9 Power Pro HD 12V Starter(HAN162) works perfectly on all Saito multi-cylinder engin- Figure 2 3. Multi-Cylinder Glow Driver There are many fine glow driver units available on the market today.
Page 8
During this time, metal 2. Use the proper glow plugs. mating parts (piston and cylinder, Your engine includes the Saito ball bearings, etc.) wear in. Care SAIP400S glow plugs, which are must be taken that the engine is...
8. Close the choke valve (92), if any angine. applicable (FA-450). 4. Be certain the mufflers are : The FA-90R3, FA-170R3, installed properly by oiling the FA-200R3 and the FA-325R5D threads and inserting the crush require priming via a syringe.
TARTING THE NGINE : The priming process for the FA-90R3 and FA-90R3 and FA- 170R3 and FA-200R3 is described as follows:For priming, inject the approximate quantity of fuel (about 1-2cc) into the carburetor with a syringe, etc. as illustrated below in figure 4.
16. Initial break-in: der (two glow plugs per cylinder) of Saito engines. It's only neces- After the engine starts, open the sary to apply heat to the rear high speed needle valve slightly.
Soft ments. mounting of Saito engines is not required due to low vibration lev- 2. Close the throttle slowly and els found in the Saito multi-cylin- adjust the low speed setting by der engines.(See Figure 6 Above)
Page 13
ARTS DENTIFICATION smoke and "stutters" or "stumbles." ed for a rich fuel mixture. 1. Your Saito engine should be Correct this by rotating the idle needle valve clockwise 1/4 to 1/2 securely mounted to the aircraft using the motor mount and hard- turn at a time until the engine ware kit provided.
Engine Maintenance Section. Timing and cam gear alignment The multi-cylinder engines are should also be done by the Saito equipped with a breather nipple. Service Center. It's recommended that a length of After approximately one hour of...
(breather nipple). Rotate the crankshaft several times. Store NGINE the engine in the box or on the To add longer life to your Saito airplane with the nose down in engine, we recommend the fol- order to keep oil in the bearings.
ROUBLESHOOTING YMPTOM AUSE OPRECTIVE CTION Engine fails to Start Low voltage on starting Replace/recharge the battery starting battery Bad glow plug(s) Inspect/Replace bad glow plugs Insufficient priming Repeat priming proce- dure "Flooded" due to Disconnect battery, excessive priming remove glow plugs and rotate propeller several times to "clear"...
Saito engine. Remember, it is imperative to balance each propeller prior to installation onto your Saito engine. Failure to do so may cause unwanted vibration in your aircraft. You will note a letter (A,B,C, etc.) stamped on the top of the motor mount.
& R ARRANTY EPAIR OLICY Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”) will be free from defects in materials and workmanship for a period of 3 years from the date of purchase by the Purchaser. 3 Year Limited Warranty Horizon reserves the right to change or modify this warranty without notice and disclaims all other warranties, express or implied.
& R ARRANTY EPAIR OLICY Warranty Services Questions, Assistance, and Repairs Your local hobby store and/or place of purchase cannot provide warranty support or repair. Once assembly, setup or use of the Product has been started, you must contact Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance.
Consumer Warranty and Repair Policy Saito engines are guaranteed against workmanship and manufacturing defects for a period of 3 years from the original date of purchase. This warranty is limited to the original purchaser of the engine and is not transferable.
Page 28
Exclusively Distributed by Horizon Hobby, Inc., Champaign, IL 61822 Copyright Sep. 2010 Stock #SAIMAN3...