Summary Of Htr 2 Modes; Using The Zr 2 Remote Control; Trigger Setup; Assigning The Trigger Output - NAD T762 Owner's Manual

USING THE HTR 2 REMOTE CONTROL
2 6 2 6 2 6
2 6 2 6
Search Mode
If none of the codes from the table, when entered, turns on the component, and if you are quite sure you
have followed the above procedure completely and carefully, you may want to try the "search" method as
follows:
Enter Library Mode by simultaneously pressing-and-holding for 3 seconds both the desired Device Selector
key and the [A/V PRESET] key, until the Learn LED turns green. Now press-and-hold the HTR 2's [ ] (or [ ])
key; the remote will step through all the available codes at a rate of approximately 1 per second. When the
component turns off, immediately release the cursor key; press [ENTER] to accept that code-library and exit
the Library Mode. Try a few commands; should you prove to have stepped past the needed code-library, re-
enter the Library Mode and use the cursor key to step back to it.
NOTE: It is possible that search mode will find code-libraries that operate, at least partially, some other-
brand (non-NAD) components. You may certainly exploit such capabilities as you find them. However,
since we can only ensure the completeness or accuracy of NAD code-libraries, we cannot support the HTR
2's operation with other-brand components.
Checking Code-Library Number
You can check the current code-library on any Device Selector key as follows. Enter Library Mode by
simultaneously pressing-and-holding for 3 seconds both the desired component's Device Selector key and
the [A/V PRESET] key, until the Learn LED turns green. Press the [DISP] key; the HTR 2 indicates the current
code-library by flashing its [TAPE], [VCR], and [MACRO] keys. For example, to indicate code-library #501 the
HTR 2 will flash [TAPE] 5 times, pause, and then flash [MACRO] once. You might wish to make a note of your
components' code-library numbers.

SUMMARY OF HTR 2 MODES

SUMMARY OF HTR 2 MODES SUMMARY OF HTR 2 MODES SUMMARY OF HTR 2 MODES SUMMARY OF HTR 2 MODES
Mode
Learn/Copy/Punch Through
Delete Mode
Macro Record
Library Mode
Back Light Timeout
Factory Reset

USING THE ZR 2 REMOTE CONTROL

USING THE ZR 2 REMOTE CONTROL USING THE ZR 2 REMOTE CONTROL USING THE ZR 2 REMOTE CONTROL USING THE ZR 2 REMOTE CONTROL
The ZR 2 remote control is a discrete compact remote for controlling the T762 from various rooms other than
the main room. The ZR 2 remote allows full separate control of the source selection irrespective to the main
room. This means the zone input may be completely different, audio and video, from the main input and
thus corresponding volume levels as well. If one wishes to enjoy the same source, as the main room the ZR
2 remote has a [LOCAL] button to allow simultaneous listening, but with full separate volume levels.
The T762's front florescent display will show activity of the zone control so that main room occupants are
aware of the zone remote activity. Furthermore if there is no main room activity, only the zone indicator will
be active in the T762's fluorescent display.

TRIGGER SETUP

TRIGGER SETUP TRIGGER SETUP
TRIGGER SETUP TRIGGER SETUP
The T 762's rear-panel TRIGGER output can be assigned to any of its six AV inputs: DVD, SAT, VCR, VIDEO
4-6. Whenever the assigned input is selected, either manually or by recalling a Preset, the TRIGGER output
will produce +12 V DC, which can be used to activate a connected component or system. See your NAD
audio specialist for more information.

ASSIGNING THE TRIGGER OUTPUT

ASSIGNING THE TRIGGER OUTPUT ASSIGNING THE TRIGGER OUTPUT ASSIGNING THE TRIGGER OUTPUT ASSIGNING THE TRIGGER OUTPUT
From the OSD's main <Setup> menu, select the <Input Settings> item using the remote's [ / ] and
[ / ] keys; use the same keys to toggle the <Trigger 1 or 2, 1 +2, MAIN, or ZONE> line. One can select
the video input (DVD, SAT, VCR, or VIDEO 4-6) you wish to assign to the TRIGGER 1 output. Furthermore the
selected Trigger 1 or 2 can be assigned to the main room, zone, or both locations. See ADVANCED OPTIONS
to assign MAIN and/or ZONE control. Select <Save and Exit> to store the trigger assignment.
Keys To Press (for 3 seconds)
Device Key + Record Key
Device Key + Return Key
Macro Key + Function Key
Device Key + Preset Key
Display Key + Digit Key
(see "Factory Reset," above)