Technical Data - Husqvarna 455e rancher ii Operator's Manual

Technical data

Engine
Cylinder displacement, cu.in/cm
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/hp @ rpm
Emissions Durability Period according to California
Air Resources Board, h.
Ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication system
Fuel tank capacity, US pint/cm
Oil pump capacity at 9,000 rpm, ml/min
Oil tank capacity, US pint/cm
Type of oil pump
Weight
Chain saw without bar or chain, empty tanks, lb/kg 13,0/5,9
Chain/bar
Standard bar length, inch/cm
Recommended bar lengths, inch/cm
Usable cutting length, inches/cm
Pitch, inch/mm
Thickness of drive links, inch/mm
Drive sprocket type/teeth
Chain speed at 133% of maximum engine power
speed, ft/s / m/s.
Recommended cutting equipment for USA
Following is a list of recommended cutting equipment for Husqvarna chain saw models 455 Rancher II, 455e Rancher
II, 455e Rancher II TrioBrake and 465 Rancher II. These chain saw models equipped with either of the listed guide bar
and saw chain combination(s), fulfills the requirements according to ANSI B175.1-2012 (Gasoline Powered Chain Saws
- Safety Requirements).
Chain saw models Husqvarna 455 Rancher II, 455e Rancher II, 455e Rancher II TrioBrake and 465 Rancher II met the
kickback performance requirements of ANSI B175.1-2012 when tested with the combinations of bars and saw chains
listed below. The saw chains Husqvarna H80 and H81 are also classified as low kickback saw chains since they met the
requirements for low kickback saw chains outlined in ANSI B175.1-2012. We recommend to use only the listed
combinations of bars and chains for chain saw models Husqvarna 455 Rancher II, 455e Rancher II, 455e Rancher II
TrioBrake and 465 Rancher II. Other chain saw models may not meet the kickback requirements when equipped with
the listed guide bar and saw chain combinations.
Recommended cutting equipment for Canada
Following is a list of recommended cutting equipment for the Husqvarna chain saw models 455 Rancher II, 455e Rancher
II, 455e Rancher II TrioBrake, 460 Rancher II and 465 Rancher II. The listed combination(s) of powerhead, guide bar and
saw chain meet all requirements outlined in Canadian Standards Assosiation Z62.1-11 (Chain Saws) and Z62.3-11
(Chain Saw Kickback).
Furthermore the saw chains Husqvarna H80 and H81 are evaluated and listed as a Type C Low Kickback Saw Chain
according to the provisions in Z62.3-11.
40 – English
TECHNICAL DATA
455 Rancher II 455e Rancher II
3
3,38/55,5
1.85/47
1,26/32
2700
2,6/3,5 @ 9000 2,6/3,5 @ 9000 2,6/3,5 @ 9000
300
NGK BPMR 7A NGK BPMR 7A NGK BPMR 7A
0.02/0,5
3
0.80/440
6-17
3
0,68/320
Adjustable
15/38
15-20"/38-51
14-19"/36-49
0.325/8,25
0.050/1,3
0.058/1,5
Spur/7
87.3/26,6
455e Rancher II
TrioBrake
3,38/55,5 3,38/55,5
1.85/47 1.85/47
1,26/32 1,26/32
2700 2700
300 300
0.02/0,5 0.02/0,5
0.80/440 0.80/440
6-17 6-17
0,68/320 0,68/320
Adjustable Adjustable
13,2/6,0 13,6/6,2
15/38 15/38
15-20"/38-51 15-20"/38-51
14-19"/36-49 14-19"/36-49
0.325/8,25 0.325/8,25
0.050/1,3 0.050/1,3
0.058/1,5 0.058/1,5
Spur/7 Spur/7
87.3/26,6 87.3/26,6
465 Rancher II
3.91/64,1
1.93/49
2.07/34
2700
3,2/4.4 @ 9600
300
NGK BPMR 7A
0.02/0,5
0.80/440
6-17
0,68/320
Adjustable
13,4/6,1
18/46
15-28"/38-71
14-27"/35-68
3/8" /9,52
0.058/1,5
Rim/7
93.5/28,5