Making Global Settings (System Setting); List Of Parameters - Boss ES-5 Owner's Manual

Making Global Settings (System Setting)

Settings that are shared by the entire ES-5 are called "system settings. "
1
Press the [EDIT] button.
2 Use the [ K ] [ J ] buttons to select the system setting
category (Play Option–Others), and then press the [ENTER]
button.
Play Option
[ENTER]
Switch Mode
PUSH

List of Parameters

Parameter Value/Explanation
Category: Play Option
Specifies the timing at which the bank or patch is changed when
you operate the switch.
Switch Mode PUSH
RELEASE
Specifies how patches are switched.
* Regardless of the Bank Chg Mode setting, the group is
switched immediately.
Bank Chg Mode
WAIT
IMMEDIATE
Specifies the operation of the EXT CTL CTL 1/2, 3/4 jacks.
LAT (Latch)
PLS
C1–4
INV
TP2 (Tap 2)
TP3 (Tap 3)
TP4 (Tap 4)
Specify the lower and upper limit of the banks that can be
Bank Extent Min, selected. Only the specified range of banks are available for
Max selection.
(Min) 1–5, (Max) 1–5
Specifies the mute time when switching patches.
Patch Chg Time
0–10
Specifies how patches are switched.
MODE1
Patch Slct Mod
MODE2
If this is ON, the BANK (MEMORY/MANUAL) indicator blinks in
Beat Indicator time with the Master BPM (p. 9) setting.
OFF, ON
12
The change happens when you press the
switch.
The change happens when you release the
switch.
Although the indication in the display is
updated to reflect the change in the bank
when a [BANK] switch is pressed, the patch will
not change until a number switch has been
pressed.
The patch switches instantly when a [BANK]
switch or any of the number switch is pressed.
Latch operation
Send a pulse when changing patches
PLS
Patch change Patch change
INV
Patch change Patch change
Turns on/off twice at the Master BPM setting
when the patch changes
Turns on/off three times at the Master BPM
setting when the patch changes
Turns on/off four times at the Master BPM
setting when the patch changes
Each time the [BANK] switch is pressed, cycle
through 1 0 2 0 3 0 4 0 5 0 1 0 ...
Press the [BANK] switch and then press a
number switch [1]–[5] to switch to banks 1–5.
Use the [ K ] [ J ] buttons to select a parameter, and then
3
press the [ENTER] button.
Switch Mode
PUSH _
4
Use the [–] [+] buttons to specify the value.
5
Press the [DISPLAY/EXIT] button several times to return to
the play screen.
Parameter Value/Explanation
Category: Preference
Specifies whether the input buffer uses the setting of each patch
or the system setting.
Input Buffer
PAT
OFF, ON
Specify whether the functions of the [BANK] switch, [MUTE]
BANK, MUTE,
switch, number switches [1]–[5], and CTL IN jack use the settings
NUMBER 1–5,
of each patch or the system setting.
CTL IN 1–2,
PAT
EXP IN
SYS
Category: MIDI Setting
Selects the operation of the MIDI OUT/THRU connector.
OUT
MIDI Out Mode
THRU
Specifies the MIDI channel on which MIDI messages are received.
Rx Ch
1–16
Specifies the device ID used to transmit and receive exclusive
messages.
Dev ID
1–32
This setting determines the basis used for synchronizing the
timing for tempo and other time-based parameters.
* When synchronizing performances to the MIDI Clock signal
from an external MIDI device, timing problems in the
performance may occur due to errors in the MIDI Clock.
Sync
INT
AUTO
Specifies whether MIDI clock messages are transmitted.
Clock Out
ON, OFF
Category: PC Map
You can use the "program change table" to freely specify the
Bank 0/PC# 1/ correspondence between program change messages received by
Memory the ES-5 and the patches that are selected.
|
Bank 1/PC#128/
111–855
Memory
Category: Others
Adjust the contrast (brightness) of the display.
LCD Contrast
1–10
Specify the polarity of the CTL IN EXP jack.
ST
Pol Exp
IN
Specify the polarity of the CTL IN CTL 1/2 jack.
ST
Pol C1, C2
IN
The settings of each patch are used.
Turns the input buffer on/off.
The settings of each patch are used.
The settings of system settings are used.
Operates as a MIDI OUT connector.
Operates as a MIDI THRU connector.
MIDI data received at MIDI IN is mixed with the
MIDI data of the ES-5, and output together.
Synchronize with the ES-5's internal clock.
Synchronize with MIDI clock received via MIDI.
However, automatically synchronize with the
ES-5's internal clock if MIDI clock messages
cannot be received.
Specify the group/bank/number of the patch
that is selected when "bank select MSB +
program number" are received.
* Bank select LSB is ignored.
If a Roland or BOSS expression pedal is
connected
If pressing or releasing the connected
expression pedal produces the opposite result
from what is expected
If a BOSS footswitch is connected
If pressing or releasing the connected
footswitch produces the opposite result from
what is expected