King Canada K-2796 Instruction Manual
  1. Manuals
  2. Brands
  3. King Canada Manuals
  4. Tools
  5. K-2796
  6. Instruction manual
King Canada K-2796 Instruction Manual

King Canada K-2796 Instruction Manual

12" dovetail jig with 1/2" template
Hide thumbs
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

12" DOVETAIL JIG
WITH 1/2" TEMPLATE
MODEL: K-2796

INSTRUCTION MANUAL

COPYRIGHT © 2002 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.

Advertisement

Table of Contents
loading

Related Manuals for King Canada K-2796

Summary of Contents for King Canada K-2796

  • Page 1: Instruction Manual

    12” DOVETAIL JIG WITH 1/2” TEMPLATE MODEL: K-2796 INSTRUCTION MANUAL COPYRIGHT © 2002 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
  • Page 2 Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations and lack of maintenance. KING CANADA shall in no event be liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.

  • Page 3: General Safety Instructions

    GENERAL SAFETY INSTRUCTIONS 1. KNOW YOUR TOOL 9. ALWAYS WEAR SAFETY GLASSES. Read and understand the owners manual and labels affixed to Always wear safety glasses (ANSI Z87.1). Everyday the tool. Learn its application and limitations as well as its eyeglasses only have impact resistant lenses, they are NOT specific potential hazards.

  • Page 4: Unpacking And Assembly

    2. Hand Levers (2). 3. Instruction Manual. 1. The K-2796 is capable of processing material up to 1 1/4” thick and up to 12” wide. The Dovetail Jig is shipped practically assembled. Assembling the 2 Hand Levers to the Dovetail Jig is the only assembly required.
  • Page 5 GETTING TO KNOW YOUR DOVETAIL JIG, SETTING & ADJUSTING Locations for all necessary Dovetail Jig adjustments. Fig.2. Hand Lever Front and back pieces mount horizontally on top of the jig and Template Knob side pieces mount vertically in the front of the jig. The insides of the boards always face out! Clamping Pressure Knob Fence Knob...
  • Page 6 GETTING TO KNOW YOUR DOVETAIL JIG, SETTING & ADJUSTING SIDE STOP SET UP The side stops serve three purposes: 1) They position each workpiece square to each other, 2) They offset the two workpieces for proper alignment, and 3) They give lateral support to the workpieces during routing.

  • Page 7: Template Adjustment

    IMPORTANT NOTE: A 1/2” TEMPLATE IS INCLUDED WITH THIS DOVETAIL JIG, IF A REPLACEMENT 1/2” TEMPLATE OR A DIFFERENT CAPACITY TEMPLATE (7/16” OR 9/16”) IS DESIRED, CONTACT YOUR Front or Back Piece LOCAL KING CANADA DISTRIBUTOR. (Horizontal) AVAILABLE TEMPLATES; Side Piece (Vertical) 1/2”...

  • Page 8: Fence Adjustment

    GETTING TO KNOW YOUR DOVETAIL JIG, SETTING & ADJUSTING FENCE ADJUSTMENT The fence controls the depth of the dovetail pins by limiting the distance that the router travels. The router stops when the router base hits the fence. The fence must be adjusted parallel to the edge of the vertical piece just like the template.
  • Page 9 OPERATIONS OPERATIONS Turn the router on and gently ease the bit into the work, letting the guide bushing gently contact the template. Facing the dovetail jig, Your router base must accept a guide bushing with a 7/16” start at your left side and work to the right, following each outside diameter and an inside diameter large enough to accept a template finger in and out.

Table of Contents