Specifications - Makita 4331D Instruction Manual

ENGLISH
1 Button
2 Battery cartridge
3 Charging light
4 Battery charger
5 Loosen
6 Hex wrench
7 Bolt
8 Jig saw blade
9 Roller
10 The end of the blade shank
should reach the bottom of the
inner slit.

SPECIFICATIONS

Model
Length of stroke .......................................................................... 26 mm
Max. cutting capacities
Wood ........................................................................................ 65 mm
Mild steel .................................................................................. 10 mm
Aluminum ................................................................................. 20 mm
Strokes per minute ...................................................................... 500 – 2,800
Overall length .............................................................................. 280 mm
Net weight ................................................................................... 2.6 kg
Rated voltage .............................................................................. D.C. 12 V
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY
CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating
instructions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
3. CAUTION — To reduce risk of injury, charge
only MAKITA type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or
sold by the battery charger manufacturer may
result in a risk of fire, electric shock, or injury
to persons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when dis-
connecting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise sub-
jected to damage or stress.
Explanation of general view
11 Lever
12 Speed adjusting dial
13 Lock-off button
14 Switch trigger
15 Base
16 Cutting line
17 Bolt
18 Cross-shaped slot
19 Edge of motor housing
20 Graduations
21 Starting hole
22 Anti-splintering device
8. Do not operate charger with damaged cord or
plug — replace them immediately.
9. Do not operate charger if it has received a
sharp blow, been dropped, or otherwise dam-
aged in any way; take it to a qualified service-
man.
10. Do not disassemble charger or battery car-
tridge; take it to a qualified serviceman when
service or repair is required. Incorrect reas-
sembly may result in a risk of electric shock or
fire.
11. To reduce risk of electric shock, unplug
charger from outlet before attempting any
ENC001-2
maintenance or cleaning. Turning off controls
will not reduce this risk.
12. The battery charger is not intended for use by
young children or infirm persons without
supervision.
13. Young children should be supervised to
ensure that they do not play with the battery
charger.
ADDITIONAL SAFETY RULES FOR
CHARGER & BATTERY CARTRIDGE
1. Do not charge battery cartridge when tempera-
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
2. Do not attempt to use a step-up transformer,
an engine generator or DC power receptacle.
3. Do not allow anything to cover or clog the
charger vents.
4. Always cover the battery terminals with the
battery cover when the battery cartridge is not
used.
23 Plastic base plate
24 Guide rule
25 Threaded knob
26 Circular guide
27 Pin
28 Fit into notches.
29 Plastic cover
30 Nozzle
31 Limit mark
32 Screwdriver
33 Brush holder cap
4331D 4333D
26 mm
65 mm
10 mm
20 mm
500 – 2,600
280 mm
2.9 kg
D.C. 14.4 V
5