Charging The Headset; Turning The Headset On/Off; Pairing The Headset - Mio BTH300 Quick Start Manual

1. Charging the headset

The headset comes with a built-in rechargeable battery, prior to using it, it is recommended to charge the battery fully for the first time. When the headset is low
power, the headset emits three "Dong" tones about every 30 seconds and the red LED flashes. Please recharge the battery of the headset.
How to charge the headset:
Plug USB charging cable into the USB port of computer and the micro connector into your headset
It will take about 3 hours to finish charging

Red light on: Charging

Red light off: Finished charging

2. Turning the headset on/off

Functions
Turning On
Turning Off
Note: In order to save power, the headset will turn off automatically if no devices are connected after 5 minues.

3. Pairing the headset

Functions
Entering pairing mode
Note: Pairing mode will last 2 minutes. If not devices can be connected after 2 minutes, it will return to standby mode automatically.
3-1. Pairing the headset—Notes
Prior to using the headset for the first time, you have to pair it with a Bluetooth-enabled device/phone. The pairing procedures may differ pending on the device
you're trying to pair . Please refer to your device user's manual for further information.
The general pairing procedures are as follows:

Keep your headset and phone within 1 meter when pairing;

Start the headset pairing mode procedure (Please refer to # 3—Pairing the Headset)

Activate your device Bluetooth function and set your device to search for Bluetooth devices within range, and select "BTH300" from the list of devices
shown;

Enter password or PIN No: "0000"( If the device supports Bluetooth V2.1, password is not required.);

If prompted by your device to connect, select "Yes"

After successfully connecting, blue LED light on the headset flashes two or three times every 4 seconds.
Notes:

If pairing failed, please turn off the headset and then re-pair according to steps 1-6 mentioned above.

If pairing is successful, the headset and the device will remember each other, they will no longer need to re-pair next time. The headset can hold up to 8 paired devices. When the
number of paired devices exceeds 8, the first one will be replaced.

Every time the headset is turned on, it will connect to last paired device automatically.
4. Pairing the headset via NFC
BTH033N support NFC function, it can quickly connect with Bluetooth smartphones via NFC.
The general pairing procedures are as follows:
1) Please activate the Bluetooth and NFC function of your smartphone (refer to your user manual for further information)
2) Pairing and connecting with your headset (see diagrams below 1-1)
Align the NFC chip of smart phone and headset within 1 centimeter. The headset will turn on and enter pairing mode automatically, there will be a request and
prompt tone on smart phone "Pair the Bluetooth device", according to prompt tone, click "Yes" to confirm. Now, the headset has already paired and connected
with your smartphone.
Note:

The smartphone screen must be unlocked in order to pair via NFC func-
tion

The NFC chip of cell phone and headset must be in 1 centimeter during
pairing

You cannot connect with your device it its in:
1. Turned off mode / standby mode

Your device must be in "pairing mode" to connect via NFC.
2
Press and hold MFB button for 3 to 5 seconds until blue LED flashes
Press and hold MFB button for 3 to 5 seconds until red LED flashes
Ensure the headset is off, and then press and hold the MFB button for 7 to 8 seconds
until red and blue LED flash alternately
Operation
Operation
Diagram 1-1
www.everik.com
LED indicator
Blue LED on one second
Red LED on one second
LED indicator
Red and blue LED flash alternately
BTH300.KM.072013.IM