Advertisement
EC-HX100M_P
MAINTENANCE
Removing the Filters
①
Turn the filter knob approx.
ten times.
Knob
•
Tap the dirt on the pleat filter
into the dust cup.
④
⑤
Pleat filter
Filter cover
Mesh filter
Filter ejector
button (red)
Washing the Filters
Pleat filter
Wash the back side thoroughly.
•
If there are heavy odors or contamination,
soak the filter in a solution of 10ml clothing-safe
bleach and 1 liter of water for approx. 3 hours.
Then, wash well with water.
After washing with water
•
Shake off as much water as possible, and then gently wipe with towels to remove excess water.
Leave the filters to dry in a well-ventilated shady place.[ Failure to dry the filters properly will cause odors or faults. ]
Guide to drying time: 12 hours (This varies by the environment and seasons.)
•
Do not dry the filters with hot air, such as with a dryer. [ There is a risk of deformation or faults. ]
8
EC-HX100M_P.indd 5
WARNING
Always disconnect the power plug
before starting servicing or inspections.
(Continued)
(There is a risk of electric shocks or injury.)
③
①
Cover portion
Dust disposal hook
(yellow)
②
Dust cup
⑥
Mesh filter
(top)
Mesh filter
(bottom)
Mesh filters (top and bottom) /
Filter cover and dust cup
Wash with water or a diluted neutral detergent.
Warming lamp (orange) lighting state
During cleaning, the Warming lamp will turn ON as shown below to indicate the operation state.
*
Slow flicker
Steady light
Start of
Air is warming up
Turns OFF if operation is
operation
stopped within 30 minutes
of starting
Warming lamp (Orange)
Lamp state
Warming air with maximum power.
Slow flicker
Dust can be vacuumed even if the air temperature is low.
Air is starting to warm up.
The cleaner's effect against mites increases with hot air.
Steady light
The time required to reach a hot air level may vary according to
the room's temperature.
The operation will automatically stop approx. one minute
after the lamp starts to flicker quickly, and the Warming lamp
will turn OFF.
To continue operation even after automatic stop, press
" " again to resume operation.
Fast flicker
For safety purposes, operation will automatically stop approx.
30 minutes after starting. The Warming lamp will flicker quickly
approx. one minute before automatic stop.
When operating with the maximum power for heating the air,
if the power is lowered by pressing " ", the lamp
will remain OFF until the air heats up.
(The lamp will automatically change to a steady light
OFF
when the hot air level is reached.)
* If hot air is discharged as soon as
operation starts, the lamp will
If the motor temperature (air temperature) is at the maximum
change to a steady light.
level, the power will not change even if " " is
Flicker 3 times
(Ex. When starting operation
pressed. The lamp will flicker quickly three times.
soon after the previous operation.)
Hints for Cleaning Mattress
•
Lightly move the cleaner slowly back and forth as shown in the illustration.
(Do not press down on the cleaner.)
•
Clean one section back and forth two times to attain a cleaner state.
•
At the start of operation, if the cleaner is set on the mattress rather
than lifted up, the hot air will circulate and warm up the air faster.
•
If there is a space between the mattress and cleaner body, the hot air
will cause fine dust to scatter and possible stick onto the cleaner body.
Cleaner body maintenance
Page
11
Storing the Cleaner
Store the power plug outside of the storage
section with the plug facing upward
Do not pinch power cord
or fingers.
[ There is a risk of power
cord damage or injury. ]
Storage stand
Cord storage section
Fast flicker
Approx. 1 minute
Auto stop
before auto stop
(Turns OFF approximately
30 minutes after starting)
Operation state
Slowly move
back and forth
Cautions
•
Do not store the cleaner into
the storage stand while it is running.
•
Do not place the stand at an unstable place,
such as a high pile carpet.
[ The stand could fall over. ]
20～30cm
•
Do not carry the cleaner around while
it is stored in the storage stand. [ The cleaner
could fall out of the storage stand and drop,
causing injuries, damage the floor,
or breaking. ]
Cord band
•
Do not pull the storage stand.
[ It could damage the floor, etc. ]
5
15/09/25 16:40
Advertisement
