Related Manuals for Alpha Comfort 3.022141
Summary of Contents for Alpha Comfort 3.022141
- Page 1 Alpha Comfort 7 Day Wireless Programmable Room Thermostat Part No 3.022141 (Single Channel) Part No 3.022142 (Two Channel) Installation and Users Instructions...
- Page 2 The Single Channel Alpha Comfort RF controller is a wireless programmable room thermostat capable of controlling time and temperature during heating on and off periods for InTec C, X and GS boilers. The Two Channel Alpha Comfort RF controller has an additional channel for programming time period for hot water heating for InTec S model boilers.
- Page 3 Fixing the Programmer to the Wall Using a small screwdriver press down on the tab at the top of the controller (4) and separate the front control panel from the rear case. Hold the rear casing in its chosen position level against the wall and mark the fixing holes.
- Page 4 Installing the Boiler Receiver Unit (Fig 3) Ensure the electrical supply to the boiler is isolated. Lower the front control cover and remove the two rubber stoppers to expose the control panel fixing screws. Remove the screws, raise the controls cover and lower the control panel. Remove the three screws securing the clock cover at the rear of the control panel and remove the cover.
- Page 5 Receiver LED Indicator The receiver LED indicator informs the user of the current operating state of the boiler, the sequence of flashes and their definition are as follows: Single Channel One flash every six seconds – standby One flash every second – communication lost (check batteries) Two flashes every six seconds –...
-
Page 6: Button Functions
Button Functions Description ""Esc" return to previous menu Comfort and economy room temperature setting button Reset remote settings Access button to time, day and timer Access button to the programming/confirm parameters menu Selector button: off, stand-by, summer and winter modes Manual, automatic functioning button Temperature decrease button Temperature increase button... - Page 7 Display Symbol Descriptions Symbol Description Symbol Description Winter mode – DHW* and Central Heating Inside temp. display enabled Summer Mode DHW enabled* Remote phone activation Request for heating Battery condition low Escape to previous screen Holiday mode Indicates it is possible to adjust a parameter using Cylinder heating in progress (if present)* buttons 11 and 12 DHW Manually ON/OFF (flashing)*...
- Page 8 Note; some icons can assume different meanings according to the context. Programming a. Set Time Press the button to enter the time setting mode, then press OK and the hour will flash. Using the +/- buttons adjust the time to the correct hour then press OK, the minutes will now flash, using the +/- buttons adjust the minutes then press OK.
- Page 9 c.(1) Set Hot Water Programme Note; The hot water programmes only need to be set when a hot water storage cylinder is present. Press the button and TIME will appear, press + twice and HW PRG will flash, press OK twice and MONDAY will appear. Using the + button you can programme individual days or blocks of days then press OK.
-
Page 10: Mode Selection
d. Setting the Temperature Note; There are two temperature settings, comfort which is the heating on setting and economy which is the heating off setting. The comfort temperature is the room temperature required during the heating on period. The economy temperature is the minimum allowable room temperature, e.g. - Page 11 b. Continuous Override The override function is used to manually control the boiler, press the button and use the +/- buttons to set the desired room temperature. To turn off the manual override press the button. c. Temporary Override To access Temporary override press the +/- buttons to set the desired temperature and the symbol will flash in the top right hand corner of the display.
- Page 12 Diagnostics Comfort RF Boiler Communication The communication between the remote and the boiler mounted receiver is identified with the symbol. There are three possible conditions shown via this symbol: 1. Symbol not present - No compatible connection between devices. 2. Symbol flashing - Connection with communication error 3.
-
Page 13: Commissioning Procedure
Regult (management of regulation parameters) (This function is not activated) Holiday Mode During winter mode function it is possible to deactivate both the hot water and central heating for a defined number of days (1 to 99). When the set number of days has past normal function will resume. When the holiday mode is set a flashing will be displayed and the number of days it is enabled for. -
Page 14: Technical Characteristics
• NTC room temp. sensor:............................50 k at 25°C • Clock indication diversion..........................+/- 15 minutes/year * = the indication of the room temperature can be affected by the point of installation of the Alpha Comfort remote control (e.g. hot wall, cold wall, height from the ground, etc.) - Page 15 Factory Settings • Central Heating Comfort Temperature ………………………………………………………………………..… 20.0 ºC • Central Heating Economy Temperature ………………………………………………………………………….16.0 ºC • Room Temperature in Manual …………………………………………………………………………….…………20 ºC • Anti Freeze …………………………………………………………………………………………………..………..5.0 ºC • Holiday Program…………………………………………………………………………………….…….. HOLIDY = OFF • Building Inertia …………………………………………………………………………………………..……..BUILD = 10 •...
- Page 16 These instructions have been carefully prepared but we reserve the right to alter the specification at any time in the interest of product improvement. © Alpha Therm Limited 2011. Alpha Therm Limited. Nepicar House, London Road, Wrotham Heath, Sevenoaks, Kent TN15 7RS Tel: 0844 871 8764 Email: info@alpha-innovation.co.uk...
Need help?
Do you have a question about the Comfort 3.022141 and is the answer not in the manual?
Questions and answers