Chauvet COLORstrip User Manual
Hide thumbs
Also See for COLORstrip:
- Quick reference manual (57 pages) ,
- User manual (19 pages) ,
- Features & specifications (1 page)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Chauvet COLORstrip
Summary of Contents for Chauvet COLORstrip
- Page 1 User Manual...
-
Page 2: Table Of Contents
IRC-6 Infrared Remote Control ..................... 13 IRC-6 Operation............................ 13 Master/Slave Mode ........................14 Master/Slave Runway Effect ......................14 5. Maintenance .........................15 Product Maintenance ........................15 6. Technical Specifications ....................16 Returns ..........................17 Contact Us ........................18 Page 2 of 18 COLORstrip™ User Manual Rev. 6... -
Page 3: Before You Begin
Chauvet assumes no responsibility or liability for any errors or omissions that may appear in this manual. Chauvet reserves the right to update the existing document or to create a new document to correct any errors or omissions. -
Page 4: Product At A Glance
Keep this User Manual for future use. If you sell the product to someone else, be sure that they also receive this document. Page 4 of 18 COLORstrip™ User Manual Rev. 6... -
Page 5: Introduction
2. I NTRODUCTION Product Overview Fuse Holder Power In Power Out Display Microphone EXT Controller Master/Slave Out Port Safety Loop Menu Buttons Sensitivity Knob In/Out COLORstrip™ User Manual Rev. 6 Page 5 of 18... -
Page 6: Product Dimensions
Product Dimensions 38 in 965 mm 6 in 155 mm 2.5 in 64 mm Page 6 of 18 COLORstrip™ User Manual Rev. 6... -
Page 7: Setup
Product Additional Products You can power link up to 15 COLORstrip™ products on 120 VAC or up to 28 COLORstrip™ products on 230 VAC. The power linking diagram corresponds to the North American version of the product ONLY! If using the product in other markets, you must consult with the local Chauvet distributor as power linking connectors and requirements may differ in your country or region. -
Page 8: Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The COLORstrip™ may be mounted in any position; however, make sure adequate ventilation is provided around the product. · Rigging Before deciding on a location for the product, always make sure there is easy access to the product for maintenance and programming purposes. -
Page 9: Operation
P000–P100 Color fade (speed) A023 All Color Chases 1–13 (speed) SdAd 001– 509 DMX Address AAAd Reset The COLORstrip™ works with a DMX controller. Information about DMX is in the DMX Linking CHAUVET® Primer, which available from Chauvet website http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf. -
Page 10: Dmx Channel Assignments And Values
000 ó 127 Slow to fast Strobe (when Ch. 1 is 010–119) 250 ó 255 Sound-Active Green (when Ch. 1 is 000 ó 255 0–100% 210–219) Blue (when Ch. 1 is 000 ó 255 0–100% 210–119) Page 10 of 18 COLORstrip™ User Manual Rev. 6... -
Page 11: Configuration (Standalone)
DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller. To run the COLORstrip™ on a static color, follow the instructions below: Static Color Press <MODE> repeatedly until SYS or ACt shows on the display. -
Page 12: Custom Color
· Set F001–F099 for auto strobe, from slow to fast. 13. Press <ENTER>. Repeat steps 3 – 12 as necessary. To black out the COLORstrip™, do the following: Blackout Press <MODE> repeatedly until SYS or ACt shows on the display. -
Page 13: Irc-6 Infrared Remote Control
The COLORstrip™ is compatible with the IRC-6 infrared remote control from Chauvet. IRC-6 Infrared Make sure to point the IRC-6 directly at the receiver on the front of the product. Remote Control IRC-6 Operation Static Color Mode Static Color mode will enable the product to output a preset color. -
Page 14: Master/Slave Mode
The Master/Slave mode allows a single COLORstrip™ product (the “master”) to control the Master/Slave actions of one or more COLORstrip™ products (the “slaves”) without the need of a DMX Mode controller. The master product will be set to operate in either Automatic or Sound-Active mode, while the slave products will be set to operate in Slave mode. -
Page 15: Maintenance
Softly drag any dirt or grime to the outside of the transparent surface. Gently polish the transparent surfaces until they are free of haze and lint. Always dry the transparent surfaces carefully after cleaning them. COLORstrip™ User Manual Rev. 6 Page 15 of 18... -
Page 16: Technical Specifications
Illuminance @ 2 m 1,104 lux Thermal Maximum External Temp. Cooling System 104 °F (40 °C) Convection I/O Connectors Channel Range 3-pin XLR Product Name Item Code UPC Number Ordering COLORstrip™ 10051063 781462214111 Page 16 of 18 COLORstrip™ User Manual Rev. 6... -
Page 17: Returns
If you are located in Mexico, contact Chauvet Mexico. · If you are located in Benelux, contact Chauvet Europe BVBA. · If you are located in any other country, DO NOT contact Chauvet. Instead, contact your local distributor. See www.chauvetlighting.com for distributors outside the U.S., UK, Ireland, Mexico, or Benelux. -
Page 18: Contact Us
(954) 577-4455 Email: tech@chauvetlighting.com Fax: (954) 929-5560 Toll free: (800) 762-1084 World Wide Web www.chauvetlighting.com UNITED KINGDOM AND IRELAND - Chauvet Europe Ltd. General Information Technical Support Address: Unit 1C Email: uktech@chauvetlighting.com Brookhill Road Industrial Estate World Wide Web www.chauvetlighting.co.uk...