A. Important Vehicle Owner Advisories:
•
At the time of this writing, the Sequent P&D system has not been certified by the California Air
Resources Board (CARB). If the vehicle is moved to California, it may not be registered
without returning the vehicle to as-close-as-possible to original condition. Please inform the
customer that emissions standards vary state to state and to check with the emissions
enforcement agency or DMV prior to moving the vehicle into another state. IMPCO is
pursuing a (CARB) certification. Contact IMPCO for certification status and updates.
•
The EPA certification on the 2009 GM 3.5/3.9L Impala covers vehicles with the E85 fuel
option. It is important that the vehicle be run on gasoline with a maximum of 10%
alcohol content with the Plug & Drive system. Operation on E85 fuel may cause rough
engine running and possible check engine light illumination during or shortly after the
changeover to CNG operation. Please advise your customers before installing the
system.
B. SEQUENT P&D 2009 3.5/3.9L Impala Installation Kit Contents:
Remove all kit package contents and verify all parts are included and undamaged. Do not attempt to
repair any damaged parts. Contact IMPCO Technologies for replacement of damaged or missing
parts.
Part Number
SQ‐50846‐02‐0010
Kit, Sequent P&D, Impala 3.5/3.9L CNG Certified
E010M9006
REGULATOR, ZENITH 1/4NPT
VI050013
CLAMP, NO.95 FOR 5X10MM HOSE
DE802060
SENSOR ASSY, MAP
FE077246
FITTING, M6 FUEL END NOZZLE
09SQ99020002G
INJECTOR,BRC LPG MAX FLOW,ORNG
H1‐51561‐003‐0900 HOSE, BRC CUT, 12MM X 900MM
VI050028
CLAMP, NO.170 FOR 12X19MM HOSE
21RG99020001
FITTING, 6MM HOSE VACUUM "Y"
06LB00001988
SWITCH, FUEL SELECTOR
DE524010
HARNESS, P&D 6 CYL, W/PTS CNG
09SQ00990002
FITTING, VAPOR FUEL Y, 10X12MM
H1‐51561‐001‐0330 HOSE, BRC CUT, 5MM X 330MM
16PM00010020
LOCKOFF, HIGH PRESSURE 1/4NPT
DE802055
SENSOR, 4 BAR PRESSURE / TEMP
21RG03010006
FITTING, 6MM BARBED
18CE00010070
MANOMETER, 0‐250 BAR, 0‐90 OHM
06LB50010068
HARNESS, PRESSURE SENSOR
H1‐51561‐002‐0900 HOSE, BRC CUT, 8MM X 900MM
25TA01010005
FITTING, NYLON "T" 16X16X8MM
H1‐51561‐001‐0700 HOSE, BRC CUT, 5MM X 700MM
09SQ99030078M
RAIL, BRC FUEL INJECTOR
09SQ99030559M
RAIL, BRC INJECTOR W/PTS PORT
B4‐51389‐001
BRACKET, RAIL 1 '08 IMPALA CNG
B4‐51390‐001
BRACKET, RAIL 2 '08 IMPALA CNG
N1‐30876‐M06
NUT, HEX FL SR M6X1.0
©2009 IMPCO Technologies, Inc.
INTRODUCTION
Description
-3-
Quantity
NA
1
20
1
6
6
1
8
1
1
1
1
6
1
1
1
1
1
1
2
1
1
1
1
1
4
2009 3.5/3.9L Impala CNG