Summary of Contents for Qualcut 3300ST
- Page 1 POWER PRODUCTS LL C. GARDEN MASTER SERIES 3300ST BRUSHCUTTER 33CC OPERA TING INSTRUCTIONS...
-
Page 2: Table Of Contents
3300ST POWER PRODUCTS LL C. CONTENTS Description of Symbols..................1 Machine Specifications ..................1 Unpacking......................1 Carton Contents....................1 Parts Diagram....................2 Applications......................3 Features........................3 Recommended Cutting Attachments..............4 Safety Instructions....................4 Effects of Vibration....................6 Repetitive Strain Injury (RSI)................6 Safe Operating Practises................7 Thrown Debris......................7 Blade Thrust (Kickback)..................7 Personal Protective Equipment.................4 Operating Tips.......................8... -
Page 3: Description Of Symbols
UNPACKING personal injury. Due to modern mass production techniques, it is unlikely that your Qualcut Brushcutter is faulty or that a part is Thrown objects can cause severe injury. missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. -
Page 4: Parts Diagram
3300ST POWER PRODUCTS LL C. 3300ST BRUSHCUTTER PARTS DIAGRAM 1. Left Handle 13. Shield 2. Right Handle 14. Nut 3. Throttle Lever 15. Sparkplug Cover 4. Lock OFF Lever 16. Engine 5. Engine Switch 17. Choke Lever 6. Safety Guard 18. -
Page 5: Applications
3300ST POWER PRODUCTS LL C. APPLICATIONS drive shaft and protects users from flying debris. The guard includes a cutting blade that automatically trims the line to the Use this product for the following domestic / household correct length. applications: Bump Feed Head •... -
Page 6: Recommended Cutting Attachments
POWER PRODUCTS LL C. RECOMMENDED CUTTING ATTACHMENTS A variety of blades are available from your Qualcut Brushcutter servicing dealer. Always use a debris shield designed for use with a blade when attaching a blade to your machine. The blade type debris shield does not have a cutoff knife. - Page 7 3300ST POWER PRODUCTS LL C. into account the working conditions and the work to be performed. b) Use safety equipment. Always wear eye protection. Safety Use of the power tool for operations different from intended equipment such as non-skid safety shoes, hard hat, or hearing could result in a hazardous situation.
-
Page 8: Effects Of Vibration
3300ST POWER PRODUCTS LL C. n) Keep cutting tools sharp and clean. Properly maintained where operating the unit or other hand-held power equipment cutting tools with sharp cutting edges are less likely to bind and is not required. are easier to control. -
Page 9: Safe Operating Practises
• Replace or resharpen dull blades. Dull blades are more likely to bind in the cut and cause blade thrust. The cutting line head or blade on the Qualcut 3300ST trimmer rotates anti-clockwise as viewed from the operator’s position, • Watch out for hidden obstacles, such as rocks, stumps, so tilting the cutting line head to the right will throw debris away roots, etc., that could cause the blade to kick back if struck. -
Page 10: Operating Tips
• Blades on Qualcut brushcutters rotate counterclockwise, as • Avoid contact with wires, wire fences, metal rods, etc. Over- viewed from the operator’s position. Therefore, the left side lapping a wire will cause the nylon line to wrap around the of the blade is moving toward you. -
Page 11: Assembly
3300ST POWER PRODUCTS LL C. • Accelerate the engine to maximum speed before starting the cut, and saw through with uniform pressure. • If shrubs or saplings bind the blade, stop the engine, and while supporting the weight of the brushcutter, push the shrub or sapling away to free the blade. -
Page 12: Fuel And Lubrication
3300ST POWER PRODUCTS LL C. Fitting the Nylon Cutting Head FUEL & LUBRICATION 1. To fit the nylon cutting head, remove the shield after releasing WARNING: Petrol is extremely flammable and the nut. Still holding the flange, place the nylon cutting head explosive. -
Page 13: Starting Checklist
3300ST POWER PRODUCTS LL C. WARNING: Move at least 9m away from the 3. Allow the fuel to drain completely. refuelling site before starting the engine. Do not 4. Screw the tank cap on. smoke while filling the tank. Do not add fuel to the tank close to an open fire or sparks. -
Page 14: Starting The Brushcutter
3300ST POWER PRODUCTS LL C. STARTING THE BRUSH CUTTER Starting the product depends on whether the engine is cold or warm. WARNING: The recoil starter can be damaged by abuse. - Never pull the starter cord to its full length. - Page 15 3300ST POWER PRODUCTS LL C. 8. If you have any difficulties, press the engine switch to OFF position, the machine will stop running. To stop the cutting head working, release the throttle lever. 9. If the machine is hot, the throttle level can be adjusted to the ON position directly when re-starting the machine and no choke will be needed.
-
Page 16: Operating The Brushcutter
WARNING: When replacing parts other than engine be removed, mark its location so that you can avoid or emissions parts, use only Qualcut replacement it with the blade. Wires can catch on the blade head parts. Use of any other parts may create a hazard and be thrown in the air. -
Page 17: The Sparkplug
3300ST POWER PRODUCTS LL C. THE SPARKPLUG THE AIR FILTER The Qualcut 3300ST uses the following sparkplugs: NGK LD L8RTF Torch BM6A Champion CJ8 Replacing the Sparkplug Cleaning the Air Filter NOTE: Before removing the spark plug, thoroughly clean the spark plug and cylinder head area. -
Page 18: The Nylon Head
3300ST POWER PRODUCTS LL C. THE NYLON HEAD Fig 2. Fig 1. WARNING! Read and understand these operating instructions, as well as the information supplied with your machine, and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders. -
Page 19: Storing Your Brushcutter
3300ST POWER PRODUCTS LL C. STORING YOUR BRUSHCUTTER Storing the product differs depending on the amount of time it will be in storage. Follow these steps to store the product short term: 1. Clean all foreign material from the product. -
Page 20: Troubleshooting
3300ST POWER PRODUCTS LL C. TROUBLESHOOTING... -
Page 21: Warranty
1. DURATION: The manufacturer warrants that it will repair or 7. RESPONSIBILITIES OF PURCHASER UNDER THIS replace, at no charge for parts or labour, the QUALCUT Brushcutter, WARRANTY: if proven defective in material or workmanship, during the following time period(s) after date of original retail purchase: A. - Page 22 3300ST POWER PRODUCTS LL C.
- Page 23 3300ST POWER PRODUCTS LL C.
- Page 24 Congratulations on your new QUALCUT Product. We are proud to have you as our customer and will strive to provide you with the best service and reliability in the industry. This product is backed by our extensive warranty and world-wide service network.