Table of Contents
Advertisement
Quick Links
GSM AD05
Please read these instructions before you start the installation
Features
•
LCD display
• Programmable 9 x 32 digit phone numbers for each trigger.
• 10 second duration recordable message for each trigger.
• Built in memory for telephone numbers and programmed setting.
•
Dual Triggers.
• SOS SMS message can be sent as alternative to voice message.
•
Programmable as Silent Alarm (dial only) or Audible (siren + dialer).
•
Cancel Message and Alarm at remote telephone using * Key or cancel
message only using # Key.
•
Programmable daily, weekly or monthly test message.
• Network Provider Field Strength Indication
Contents
• 1 x GSM Auto Dialer.
• 1 x Fixing kit and Installation & Programming guide.
Tools required:
• Small cross head screw driver
• Large cross head screw driver
• Number 6 masonry drill bit
• Hammer drill
• Small hammer
• Pencil, ruler and spirit level
The Auto Dialer.
Important: before you install the Auto Dialer please take these into consideration.
1. Before you start to drill holes check for hidden wires and pipe work.
2. Keep the Auto Dialer out of reach of small children.
Slave GSM Auto Dialer- Instruction Manual
1
Advertisement
Table of Contents
Related Manuals for Response Electronics GSM AD05
Summary of Contents for Response Electronics GSM AD05
- Page 1 GSM AD05 Slave GSM Auto Dialer- Instruction Manual Please read these instructions before you start the installation Features • LCD display • Programmable 9 x 32 digit phone numbers for each trigger. • 10 second duration recordable message for each trigger.
- Page 2 Installation How to install the Auto Dialer 1. Mark and drill two holes on a horizontal line 160mm apart. 2. Insert the masonry plugs; screw the two fixing screws in the plugs leaving 2mm protruding. 3. Run a cable from the Alarm Control Panel to the Auto Dialer. 4.
- Page 3 Programming Guide How to program the Auto Dialer (if no key is pressed for 30 seconds, the dialer will automatically exit the programming mode.) IMPORTANT: THE SYSTEM MUST BE IN THE OFF MODE FOR ALL PROGRAMMING. SINCE THE DIALER WILL AUTOMATICALLY TURN ITSELF ON WHEN POWER IS FIRST CONNECTED OR RECONNECTED, YOU NEED TO TURN THE DIALER OFF (ENTER CODE, DEFAULT 1234 AND THEN PRESS EXIT KEY) BEFORE YOU CAN START PROGRAMMING AS BELOW.
- Page 4 Programming Guide How to designate between Voice and SMS messages being sent : Quick guide: Press 1234 > PROGRAM > 0 > ENTER > 1 > ENTER > 0 > ENTER (Voice message) Press 1234 > PROGRAM > 0 > ENTER > 1 > ENTER > 1 > ENTER (SMS message) How to program for a voice message : Quick guide: 1.
- Page 5 Programming Guide How to delete phone numbers : Quick guide: Press 1 2 3 4 > PROGRAM > 3 > ENTER > 1 > ENTER > ESC (Please note: 1 = 1st telephone number, 2 = 2nd number and so on) 1.
- Page 6 Programming Guide How to set Trigger Delay/Arm Delay times: (Default both set at 0 seconds, instant) Set trigger delay time between 30 and 60 seconds: This is the delay time between a trigger being activated and the time the dialer starts to dial out. Default setting is 0 seconds. Quick guide: Press 1 2 3 4 >...
- Page 7 Programming Guide How to stop the dialer dialing the telephone numbers in sequence : Quick guide: When the phone is answered, press <#> or <*> on the telephone keypad to stop the dialing sequence. When the Auto Dialer starts dialing, it will dial the first telephone number and repeat the pre-recorded voice message five times.
Need help?
Do you have a question about the GSM AD05 and is the answer not in the manual?
Questions and answers