Advertisement
Verifying the Settings
In addition to verifying the settings after configuring the Go!Bridge IP
Communicator, you can also verify the settings at any time as follows:
1
At the Control Panel's Home screen, tap Security.
2
Tap Menu.
3
Tap Toolbox.
4
In the Enter Your Code to Access the Toolbox screen, enter the
master user code.
5
Tap → to scroll to the Toolbox (3 of 3) screen. Then tap Go!Bridge
IP Communicator Status.
A summary screen displays the following information:
•
Network Configuration. The network type configuration.
•
IP Address. The IP Address for the Go!Bridge IP Communicator.
This is a 32‐bit numeric address that identifies the device on the
network.
•
Subnet Mask. The subnet mask for the network. All devices that
are joined to a network belong to a subnetwork.
•
Gateway. The IP Address for the access point to the external
network. Typically, this is the IP Address of the local network
router or node that control traffic for your ISP.
•
MAC Address. This is the Media Access Control (MAC) Address.
It is a physical address that is encoded to the Go!Bridge IP
Communicator during the manufacturing process.
Testing
The Go!Bridge IP Communicator tests the network connection to the
third‐party monitoring service. A report shows if Go!Bridge IP
Communicator has successfully connected (or failed to connect) to the
external server.
Registration
To register the Go!Bridge IP Communicator with the monitoring service,
refer to your specific provider's registration instructions.
SPECIFICATIONS
Wireless Signal Range
500 ft (152.4 m), open air, with Wireless Control Panel
Transceiver
Silicon Labs SI1001‐E‐GM2
Transceiver Frequency
25 channel frequency‐hopping spread spectrum, 403
kHz channel spacing (910.2‐920.275 MHz)
Modulation Type
GFSK modulation, 128 kpbs
RF Power
+19dBm Maximum
Ethernet
10/100 BaseT
Dimensions (L x W x H)
6.24 x 4.5 x 1 in (159 x 114 x 25 cm)
Weight
9.6 oz
Housing Material
Cycoloy™ Resin C2800 (Rated to UL 94 V‐0:
Flammability Standard)
Color
White
Operating Temperature ‐32° F to 120° F, (0° C to +49° C)
Relative Humidity
5‐95% Non‐Condensing
Operating Voltage
5VDC
Certification
ETL, FCC, IC, IFETEL, and NOM
Important Note
Should the local network lose Internet access due to a power outage or
interruption, the Go!Bridge IP Communicator is not equipped with a
backup battery system. To best prepare for power failures and to ensure
the security system maintains Internet access with the monitoring
service for life‐safety communications during power failures, the local
network must have a dedicated Uninterrupted Power Supply (UPS) or
backup battery solution from a third‐party manufacturer in place.
Linear LLC does not supply, provide, recommend, or test the Go!Bridge
with any UPS or battery backup solution. It is also assumed that owner's
Internet Service Provider (ISP) maintains a backup battery (or power
generator) for their remote network equipment.
Go!Bridge IP Communicator | Installation Instructions
REGULATORY INFORMATION
Wireless Product Notice
Radio controls provide a reliable communications link and fill an
important need in portable wireless signaling; however, there are some
limitations which must be observed.
•
For United States Installations Only: The radios are required to
comply with FCC Rules and Regulations as Part 15 devices. As
such, they have limited transmitter power and therefore limited
range (approximately 400 ft.).
•
A receiver cannot respond to more than one (1) transmitted
signal at a time and may be blocked by radio signals that occur
on or near their operating frequencies, regardless of code
settings.
•
Changes or modifications to the device may void FCC
compliance.
•
Infrequently used radio links should be tested regularly to
protect against undetected interference or fault.
•
A general knowledge of radio and its vagaries should be gained
prior to acting as a wholesale distributor or dealer, and these
facts should be communicated to the end users.
FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1
This device may not cause harmful interference, and
2
This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for
Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one(1) or more of the
following measures.
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
•
Consult the dealer or an experienced radio/TV technician for
help
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
Copyright © 2014 Linear LLC
3
Advertisement
