Advertisement
Go!Bridge IP Communicator | Installation Instructions
NOTE: If the 900MHz LED illuminates in GREEN (the lower LED),
verify that the network cable is not connected to the Go!Bridge
IP Communicator. If the cable is disconnected and it is still
illuminated GREEN, use the end of an open paperclip to press
and release the recessed Reset button. The button is located
inside the small hole on the port side of the Go!Bridge IP
Communicator, directly above the Ethernet port. This restores
the factory settings. See Figure 3 Go!Bridge IP Communicator
Rear View—Ports and Recessed Reset Button.
Figure 3 Go!Bridge IP Communicator Rear View
Recessed Reset Button
A Recessed Reset Button
B Ethernet Port
C
Power Supply Port
5
After the Go!Bridge IP Communicator is powered ON, continue with
Programming the Go!Bridge IP Communicator into the Control
Panel.
Programming the Go!Bridge IP Communicator
into the Control Panel
Use these steps to place the control panel and Go!Bridge IP
Communicator in learning mode. This gives the control panel the ability
to learn the network settings transmitted by the Go!Bridge IP
Communicator.
NOTE: To scroll between op ons on the control panel, tap the ←
and → arrows. To move to the previous or next prompt tap the
↑ and ↓ arrows.
1
Connect an Ethernet cable (not included) to the router and
Go!Bridge IP Communicator. Do not plug the cable into the uplink
port.
For compliance with UL 1023: Household Burglar‐
IMPORTANT:
Alarm System Units, the Go!Bridge must be installed in the
same room as the Internet modem or router.
2
Ensure the control panel is powered ON. Then tap the Home
button.
3
Tap the system logo in the lower‐right corner of the control panel
Home screen.
4
At the Enter Your Code screen, enter the four (4)‐digit master
installer code to go to the Installer Toolbox (1 of 2) screen.
5
At the Installer Toolbox (1 of 2) screen, tap System Configuration.
6
At the Q1: Select RF Sensor # (01 to 48) screen, tap Go To.
7
At the Enter Question Number (2 Digits) screen, enter 92.
8
At Q92 Select Network Device (0 to 1), tap → to scroll to (1)
Go!Bridge IP Communicator. Then tap ↓.
2
Copyright © 2014 Linear LLC
9
10 On the Go!Bridge IP Communicator, press and release the Learn
—
Ports and
11 At the Pair with Xcvr Device screen, tap OK. Then tap ↓ to
Configuring the Go!Bridge IP Communicator Settings
1
2
3
4
NOTE: A trouble alert consists of an audible beep and the Control
5
6
7
8
LED Indicators
The table details the LED indicators on the Go!Bridge IP Communicator.
Network LED
Solid GREEN
Flashing GREEN Network cable is plugged in and IP address is actively being
Solid RED
900 MHz LED
Solid GREEN
Flashing GREEN Linked to the Control Panel. Communication issues exist.
Solid RED
Flashing RED
At Q: Network Device ID (Read Only), tap Learn. This gives the
panel the ability to discover the read‐only network device ID
transmitted by the Go!Bridge IP Communicator.
At the Pair with Xcvr Device screen, the "initiating learning
process" message appears.
button (this is the small, black plastic button on the LED side of the
Go!Bridge IP Communicator below the 900MHz LED). This transmits
the device ID to the Control Panel.
When the "learn operation succeeded" message appears and the
panel displays the Type (Go!Bridge IP Communicator) and ID#, the
Go!Bridge IP Communicator and panel are linked. The 900MHz LED
on the Go!Bridge IP Communicator also flashes GREEN.
continue with Configuring the Go!Bridge IP Communicator Settings
below.
At the Q: Select Port # (1 to 8) screen, enter the port number for
the third‐party monitoring services' server. Then tap ↓.
At Q: Used (0 to 1), tap → to select one (1) of these options:
•
(0) Disabled (Recommended). This is the default setting. Most
users will keep this port disabled. Then tap Next and skip to
step 3.
OR
•
(1) Enabled. Then tap ↓. At the Q: Enter Port Value (0‐65535)
screen, tap ↓ to accept the default port value. Next, at the Q:
Enter Port Forward IP Address screen, tap ↓ to accept the
address configured by the provider. You can configure up to
eight (8) ports. If you are finished configuring ports, tap Next.
At the Summary of Network Device screen, tap ↓. Verify the list of
port numbers and forward IP addresses appears as programmed.
Then tap Skip.
At Q93 Enter Broadband Network Failure Time (1 to 255), enter
the desired number of minutes that must pass before a network
failure triggers the Control Panel to issue a trouble alert. The
default value is 30 minutes. Then tap ↓.
Panel's Home screen displays a trouble message.
At Q94 Select Broadband Network Failure Report (0 or 1), tap → to
select whether or not to report the broadband network failure to
the monitoring service:
•
(1) Enabled. This is the default setting. Network failures are
reported to monitoring service.
OR
•
(0) Disabled. Network failures are not reported.
Tap End.
At the Summary of System Configuration screen, verify the
settings. Then tap Save Changes.
Tap Exit to the close the System Configuration screen.
Globe Icon
Indicates the presence of an external network connection.
assigned.
Network cable unplugged.
Icon Labeled "900MHz"
Linked and communicating with the Control Panel.
Not linked to the Control Panel, turns solid after a device
reset.
Not linked to the Control Panel.
Advertisement
