Advertisement
Quick Links
2GIG-BRDG1-900
GO!BRIDGE IP COMMUNICATOR
INSTALLATION INSTRUCTIONS
The Go!Bridge IP Communicator™ (2GIG‐BRDG1‐900) provides Internet
connectivity between the monitoring service's Central Station and the
Go!Control® Panel, when the panel is used as a household burglar alarm
system.
It supports automatic firmware updates, provides interactive security
services, and increases supervision using signal‐forwarding to the Central
Station. For wireless communication with the Control Panel, the 900MHz
Transceiver Module (2GIG‐XCVR) must be installed in the panel. For
Internet access, the Go!Bridge must be connected to the local network
router using an Ethernet cable (not provided).
Contents
Verify that the package includes the following:
•
1—Go!Bridge IP Communicator
•
1—5VDC USB Mini‐B Power Supply
•
1—Stand
•
1—Plastic Power Supply Bracket (includes Self‐Adhesive Backing
and Zip Tie)
•
1—Wall Socket Screw for Power Supply Bracket
•
2—Phillips Head Screws and Wall Anchors (to mount unit on wall)
•
4—Self‐Adhesive Vinyl Bumpers for use on unit or stand
Requirements
Before you install, program, and test the Go!Bridge IP Communicator,
ensure the control panel being paired with the Go!Bridge IP
Communicator meets these requirements:
•
Firmware Version 1.12 (or higher)
•
2GIG‐XCVR 900 MHz Transceiver
For compliance with UL 1023: Household Burglar‐
IMPORTANT:
Alarm System Units, the Go!Bridge must be installed in the
same room as the Internet modem or router.
NOTE: To protect data sent via the local wireless network, it is
recommended that you install the Go!Bridge IP Communicator on
a local network where either WPA (Wi‐Fi Protected Access) or
WPA2 (Wi‐Fi Protected Access II) encryption is already enabled.
After installing, programming, and testing the Go!Bridge IP
Communicator, you will need to register a new customer with the third‐
party monitoring service. See Registration on page 3.
Figure 1 Go!Bridge Front View—LED Indicators and Learn Button
A Network LED
B 900 MHz LED
C Learn Button
Powering ON the Go!Bridge IP Communicator
Use these steps to power ON the Go!Bridge IP Communicator:
1
Attach the power supply to the bracket (provided) as follows:
1a Insert the power supply into the enclosure on the plastic bracket.
See C in the figure below.
1b Secure the power supply to the retaining bracket by threading a
zip tie through the bracket's slots. See D in the figure below.
1c Remove the strip from the self‐adhesive backing on the power
supply bracket.
1d Affix the adhesive on the bracket to the wall outlet. Then secure
the bracket to the outlet with the wall socket screw (provided).
NOTE: Always use the provided power supply bracket in the United
States (and other countries where it is required). Canada does not
require the power supply retaining bracket.
Figure 2 Power Supply and Bracket
A 110V Wall Outlet
B
Plastic Power Supply Bracket with Adhesive Backing
C
AC Power Supply
D Zip Tie
2
Connect the Go!Bridge to the power source.
NOTE: Do not connect an Ethernet cable to the Go!Bridge IP
Communicator at this time. You will connect the cable when
completing the steps in Programming the Go!Bridge IP
Communicator into the Control Panel.
3
(Optional) Place the stand (provided) on a counter, desktop, or other
flat surface. Set the Go!Bridge IP Communicator in the stand.
NOTE: To protect surfaces from damage, affix the self‐adhesive vinyl
bumpers to the unit or stand.
4
Verify that the two (2) LEDs on the Go!Bridge IP Communicator
illuminate in RED. See Figure 1 Go!Bridge Front View—LED Indicators
and Learn Button on page 1.
Copyright © 2014 Linear LLC
1
Advertisement
Related Manuals for 2gig Technologies 2GIG-BRDG1-900
Summary of Contents for 2gig Technologies 2GIG-BRDG1-900
-
Page 1: Installation Instructions
2GIG-BRDG1-900 GO!BRIDGE IP COMMUNICATOR INSTALLATION INSTRUCTIONS Powering ON the Go!Bridge IP Communicator Use these steps to power ON the Go!Bridge IP Communicator: The Go!Bridge IP Communicator™ (2GIG‐BRDG1‐900) provides Internet Attach the power supply to the bracket (provided) as follows: connectivity between the monitoring service’s Central Station and the Go!Control® Panel, when the panel is used as a household burglar alarm 1a Insert the power supply into the enclosure on the plastic bracket. system. See C in the figure below. It supports automatic firmware updates, provides interactive security 1b Secure the power supply to the retaining bracket by threading a services, and increases supervision using signal‐forwarding to the Central zip tie through the bracket’s slots. See D in the figure below. Station. For wireless communication with the Control Panel, the 900MHz 1c Remove the strip from the self‐adhesive backing on the power Transceiver Module (2GIG‐XCVR) must be installed in the panel. For supply bracket. Internet access, the Go!Bridge must be connected to the local network 1d Affix the adhesive on the bracket to the wall outlet. Then secure router using an Ethernet cable (not provided). the bracket to the outlet with the wall socket screw (provided). Contents NOTE: Always use the provided power supply bracket in the United States (and other countries where it is required). Canada does not ... -
Page 2: Led Indicators
Go!Bridge IP Communicator | Installation Instructions NOTE: If the 900MHz LED illuminates in GREEN (the lower LED), At Q: Network Device ID (Read Only), tap Learn. This gives the verify that the network cable is not connected to the Go!Bridge panel the ability to discover the read‐only network device ID IP Communicator. If the cable is disconnected and it is still transmitted by the Go!Bridge IP Communicator. illuminated GREEN, use the end of an open paperclip to press At the Pair with Xcvr Device screen, the “initiating learning and release the recessed Reset button. The button is located process” message appears. inside the small hole on the port side of the Go!Bridge IP 10 On the Go!Bridge IP Communicator, press and release the Learn Communicator, directly above the Ethernet port. This restores button (this is the small, black plastic button on the LED side of the the factory settings. See Figure 3 Go!Bridge IP Communicator Go!Bridge IP Communicator below the 900MHz LED). This transmits Rear View—Ports and Recessed Reset Button. the device ID to the Control Panel. — Figure 3 Go!Bridge IP Communicator Rear View Ports and When the “learn operation succeeded” message appears and the panel displays the Type (Go!Bridge IP Communicator) and ID#, the Recessed Reset Button Go!Bridge IP Communicator and panel are linked. The 900MHz LED ... -
Page 3: Regulatory Information
Go!Bridge IP Communicator | Installation Instructions Verifying the Settings REGULATORY INFORMATION In addition to verifying the settings after configuring the Go!Bridge IP Communicator, you can also verify the settings at any time as follows: At the Control Panel’s Home screen, tap Security. Tap Menu. Tap Toolbox. In the Enter Your Code to Access the Toolbox screen, enter the master user code. Tap → to scroll to the Toolbox (3 of 3) screen. Then tap Go!Bridge IP Communicator Status. A summary screen displays the following information: • Network Configuration. The network type configuration. Wireless Product Notice • IP Address. The IP Address for the Go!Bridge IP Communicator. This is a 32‐bit numeric address that identifies the device on the Radio controls provide a reliable communications link and fill an network. important need in portable wireless signaling; however, there are some • Subnet Mask. The subnet mask for the network. All devices that limitations which must be observed. are joined to a network belong to a subnetwork. • For United States Installations Only: The radios are required to • Gateway. The IP Address for the access point to the external comply with FCC Rules and Regulations as Part 15 devices. As ... -
Page 4: Limited Warranty
Go!Bridge IP Communicator | Installation Instructions Industry Canada (IC) Compliance LIMITED WARRANTY This device complies with Industry Canada license‐exempt RSS This Linear product is warranted against defects in material and standard(s). Operation is subject to the following two conditions: (1) workmanship for two (2) years. This warranty extends only to wholesale this device may not cause interference, and (2) this device must accept customers who buy direct from Linear LLC or through Linear LLC’s any interference, including interference that may cause undesired normal distribution channels. Linear LLC does not warrant this product operation of the device. to consumers. Consumers should inquire from their selling dealer as to Repairs to certified equipment should be made by an authorized the nature of the dealer’s warranty, if any. Canadian maintenance facility designated by the supplier. Any repairs or There are no obligations or liabilities on the part of Linear LLC for alterations made by the user to this equipment, or equipment consequential damages arising out of or in connection with use or malfunctions, may give the telecommunications company cause to performance of this product or other indirect damages with respect to request the user to disconnect the equipment. loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties for functionality, are valid only Users should ensure for their own protection that the electrical ground until the warranty expires. This Linear LLC Warranty is in lieu of all other connections of the power utility, telephone lines and internal metallic warranties expressed or implied. water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. WARNING: Users should not attempt to make such connections themselves, but should contact the appropriate electric ...